Is there a way to get these throttles to work with a potentiometer type motor controller. I think the call them pwm?
@heidenburg5445 Жыл бұрын
This is the kind of knowledge I like to hear :D Real knowledge!!
@misoo834 ай бұрын
Hi, i have thumb throttle that have start idle voltage 1.33v and when full run 3.42v, is this ok voltage, is this throttle ok and will this throttle work fine with such voltage values?. Thanks 🙂
@express3754 жыл бұрын
Thankyou so much for this, attempting to use this type of pedal to control a solenoid graver me and my wonderful subs are working on, this is a great help even better if I was clever like you blokes :) . What one has the smothest control. Got a few cheap one form ebay to experiment ,Cheers Shaun
@taitheguy855 жыл бұрын
Wish you knew/explained how to connect that 5 wire display/switch throttle. The blue&yellow wires have me stumped
@de_dorf2793 жыл бұрын
By any chance have u figured out what to do with the blue & yellow wires yet. They got me stumped
@jaguapasto19823 жыл бұрын
The blue, and yellow is for the ignition, or Power locks...
@yusifsuleiman5502 Жыл бұрын
Hi, please, I replaced pedal assistant sensor with a throttle on my ebike and it not working. How do I fix the issue. The controller doesn't have separate wire for throttle connection. Greetings from Nigeria
@Antrod2 жыл бұрын
So I have a question. If a throttle advertises that it's Voltage is 12-99v, does that mean it's compatible for anything between 12 and 99? So if my bike is 36v, it's not going to blow it?
@anio68652 жыл бұрын
I have a controller. It has 4 wires to 1 jst-sm. 2 pins for the brakes. And 2 for the throttle, which is a julet 3 pin which the connected julet 3pin cable is only 3 inches long. If I get a longer julet 3pin with open wires on the end. So I am wondering how I connect them ? I bought them from Fiido. They are a matching couple for the L3 bike. Would I wire the green and red together ? Or would I wire either the green or the red one or the other with one of the brake wires ?
@starlord8200 Жыл бұрын
So, and if lcd display have hall wire its using for connection signal wire?
@mrdrags6828 Жыл бұрын
Is there a way to bypass it with a button
@anio68652 жыл бұрын
I have a controller. And on the controller is a jst-sm 4 pin connector for both the brakes and the throttle together. 2 are for the brakes and that leaves 2 more pins which are of course for the throttle. But, the throttle has 3 pins. I dont have a multimeter and I have never used one. So,, if I switch the pins around to figure out which pin goes where. Could that harm my bike in any way ?
@nativealien18 ай бұрын
great video , my gf wants to know where she can get a banana like that one.
@lostinthemoonlight4 жыл бұрын
Now I want to power my ebike with a bunch of bananas.
@gewizz24 жыл бұрын
what i want to know is, can you just connect the signal wire to the positive wire? just to get home, like today my ebike has stopped, if i knew ii could just connect the sig to + i might have been able to get home, with no throttle control ofcourse.
@truth.speaker3 жыл бұрын
That's my question
@gewizz23 жыл бұрын
@@truth.speaker oh my friend, i know what is the situation now, you need a button battery which is 5volts, you then connect 2 of the 3 wires to each side of this battery, thn you hav throttle. since then ive moved on to a gas powered china doll engine for long range!!!
@kingsleysarfo.4 жыл бұрын
I had no idea that throttles have levels depending on how hard your thumb presses it... I’ve been pressing the throttle so hard no wonder the battery dies
@russellbumak4 жыл бұрын
I have female plug in, how I get thumb T for my bike
@z4u682 жыл бұрын
Hi , my aventure throttle only grabs at eight miles an hour, half the lower speeds are missing, should this be like this? Its made by aventon Thank you in advance
@yokanshree46212 жыл бұрын
Is it waterproof
@ShanenWay9 ай бұрын
So it's a potentiometer
@johnphotograpy1353 ай бұрын
no
@truthseeker30904 жыл бұрын
I need help reconnecting my ebike. Could you help me?
@skepticfucker2804 жыл бұрын
Is it the same as magnetic throttle? I have a twist and thumb throttle from 2 different scooters. The thumb throttle only has 2 magnets and a sensor not sure if I want to open the other yet. But yeah, are all electric 3 wire throttles compatible with all 3 wire controllers and is it the same for 3 wire breaks? Sorry for the long message and thanks again.
@grahampennack57563 жыл бұрын
Hi. Your advice please. Samebike L026 350w motor. After about 10mins ride lose (thumb) throttle power. Sometimes occasionally returns. When starting from rest again similar situation. Thankyou.
@StanFranChaisur2 жыл бұрын
how to connect simple thumb the three wires black green and red on controller six color display socket red black white green brown yellow
@timhinds90893 жыл бұрын
Can I use this thing on a ride on 12v lead acid battery.ATG?
@S.huddo-db3ew8 ай бұрын
I had a feeling they are magnets
@eltaccco80352 жыл бұрын
Thank you!
@bwnco3 жыл бұрын
Someone please show how to do an install on a bike that does not have one....
@jacobclark892 жыл бұрын
☠️ I've been experiencing extremely dangerous episodes of the motor not stopping as soon as I turn the throttle , related to high humidity conditions ! I think it's because the humidity increases conductivity of the hall sensors in the throttle . can you recommend a good throttle ? I think the manufacturers are going to have to make them water proof. I experienced the same issue with a different throttle , battery and controller. just using the bike after a rain storm is enough to cause the issue. We must have a throttle will a switch to cut power ! ☠️ Also stop using hot glue on the Hall sensors ! It melts were I live ! And make the throttle not Fall apart so easy , and they need to be made with softer grips or made to accept normal grip's.
@jayy61192 жыл бұрын
Stop copy and pasting this
@jumpingscary514 Жыл бұрын
warninggg i copy your face and paste in google 👍🏻
@Rc-Adventurers5 жыл бұрын
Help my scooter controller has green, black, red, gray, orange. The new throttle LCD and has red, black, green, blue and yellow. Red to red, black to black green to green...... gray and orange? And blue and Yellow?
@raspberryeditingvideo43315 жыл бұрын
Do you know how can i run a mosfet irfz44n with this throttel?
@slabjudah8927 Жыл бұрын
MAGNETS. HOW DO THEY EVEN WORK
@hakkiali11034 жыл бұрын
But if throttal volt from 0.8v to 3.6 v is it ok or not thanks
@ajinajinkj76112 жыл бұрын
How too bye this
@aliasprojects62146 жыл бұрын
My throttle is not engaging my motor. Wiring is correct. Brand new bike, motor and controller are good. Any suggestions?
@joblessalex5 жыл бұрын
If it isn't working still, battery voltage?
@LuiscarVilla2 жыл бұрын
thanks a lot
@alansmemoriesofnothingands80296 жыл бұрын
Do you install throttle on emtbs
@maricelsimpauco19834 жыл бұрын
Can you use this throttle in a 24v or higher scooter?
@ballaratebikes2874 жыл бұрын
Maricel Simpauco every controller sends five volts to the throttle regardless of the battery’s voltage.
@alexshatner3907 Жыл бұрын
@@ballaratebikes287 I have a great question for you, I am interested in a twist throttle that starts you off slow, because I notice that all the cheap $15 twist throttles that I a have used, knock you off the saddle as soon as you barley turn it to its minimal activation point, I am looking for a throttle that starts off very slow and gradually starts accelerating to full speed. Please refer me to one either through amazon link or a model and model number, I will subscribe to your channel upon you response. thanks
@imnotbeluga0073 жыл бұрын
I thought these were potentiometer based... turns out that there is more than 1 type...
@TyXtra4 жыл бұрын
Hey are you on insta I need to ask for advice please
@sagarchoudhary97766 жыл бұрын
Sir the second throtlle which has 5 wires please tell me how to connect this type throttle to 24v 250w speed controller....
@ballaratebikes2876 жыл бұрын
Sagar Choudhary please ask your supplier. Anyone who supplies goods without support needs to be held to account.
@patch6434 жыл бұрын
Haha!! Banana! LOL!!
@byronclassiccars33034 жыл бұрын
Hi I have a Ktm e-xc which has a really long throttle action is there a way of making it shorter (less movement to full throttle)