Panic Mode Day 47

SUBSCRIBE AND GET NOTIFICATIONS!
kzbin.info...
CHECK OUT THESE PLAYLISTS OF REPAIR SERIES AND OTHER FUN STUFF!
(To go to the Playlist Menu page, Click here: )
kzbin.info...
1969 Dodge D300 Power Steering Retrofit Install
• 1969 Dodge D 300 Power...
Bringing It Back To Life: 1968 F 250 Camper Special
• Bringing It Back To Li...
1958 GMC Resurrection
• 58 GMC Resurrection Pa...
1941 Dodge WC6 Command Car Entire Series
• 1 of 15 1941 Dodge Pow...
Master Craft Mower Resurrection
• Mastercraft Mower Resu...
1957 Chevy 5400 Low Cab Forward Rescue
• Pt 1, 1957 Chevy 5400 ...
Snow Smashed Shop Recovery
• Snow Smashed Shop Reco...
Operation Crusty Truck
• Operation Crusty Truck...
2014 Hayfield Follies!
• Hayfield Follies Part 1
1985 Dodge One Ton 4x4
• 1985 Dodge One Ton 4x4...
Meyer E 47 Snow Plow Installation
• Part 1/6 1969 GMC 4x4 ...
The 1968 GMC Water Truck Adventures
• Part 1 Air Heater Expe...
1946 ACF Brill
• 1948 ACF BRILL 35 foot...
1975 Chevy Half Ton
• 1 of 3 75 Chevy half ton
1985 Chevy Silverado Half ton
• Redneck Restoration's ...
1959 Pontiac 389 resurrection for "The Find" 1956 GMC
• Part1 1959 Pontiac 389...
IHC 300 Utility Camshaft Repair
• Part1 International 30...

[@xcop4511]

I never get tired of watching Jeff do stuff... xCop

[@macgvrs]

I have often said, when working on the some engineering marvel that was horrible to work on, that the engineers who design such things should be made to work on them. That would probably improve the engineering , one would hope. Making progress, hope you make your deadline.

[@MrJim0823]

Thanks Jeff

[@DanEBoyd]

Those MAP torches do make darned good charcoal lighters, when grilling.

[@BulletmanDoom]

I don't believe you told us why the truck has to be ready in 47 days from now or did I miss that somewhere?

[@drcornelius8275]

I think it's either that rapture and end times prediction..... or Vinny said he had 70 days to pay up

[@b.abrackus6403]

I have never seen Jeff answer comments, occasionally he might refer to a comment during a video..opps l guess he said he is 62

[@chevyfan82]

Panic mode day 70 about half way through video jeff says why it has to be done.

[@BulletmanDoom]

@@chevyfan82 Thanks, I watched that and all of Jeff's stuff for that matter but I misunderstood what he was saying. Now that I've watched it again I understand. Great content as always and youtube is a better place when Jeff's about.

[@rodmacisaac5963]

Thanks Jeff 😎

[@1962mrmongoman]

coming along well Jeff

[@martinbalmforth2665]

He was over Under and he was Over Dunn..

[@DanEBoyd]

I thought Dunn was in California?

[@martinbalmforth2665]

Those cluckers were annoying

[@glenharper3136]

Thanks for the video Jeff.

[@timothyfritsch8801]

your doin it man your doin it WOW i could never do that job

[@BeagleFanatic1]

Great video Jeff, you are putting a lot of time on the floor covering. Did the factory original floor go that far up the fire wall? I ask because you are spending a ton of time cutting and trimming it to fit properly.

[@Gordonseries385]

👍 🐓

[@TheRebelOne.]

I have a very important question ? What age are you? Kind regards from Ireland 🇮🇪.

[@ElderlyIron]

62

[@TheRebelOne.]

@@ElderlyIron Thankyou so much for your reply. I love your work ethic and attention to detail in everything you do. And my young daughter always loves your video entre by banging loudly on sheet metal. Enjoy your weekend.

[@MADKIWI]

Howdy Jeff. I do hope I'm not going to say the obvious, m8.... Did you put hose clamps on the ½ / ¾ rubber hose in the heater box? Kick my bum and call me names.....😊

[@Hillbillyhacks77]

I thought I saw there was a clamp missing too

[@ElderlyIron]

They're in there!

[@timothyfritsch8801]

im just happy you didnt get hair dryer syndrome cause it makes it worse

[@brianandlindafairchild1237]

Were you talking to me

[@darrinfry2251]

Trump2024😊

[@kriswright1022]

For prison.❤

[@darrinfry2251]

@@kriswright1022 like your President now

[@darrinfry2251]

@@kriswright1022 Trump 2024 🦾