EZ 2003 Kia Sorrento timing marks

I was replacing the timing belt and cam and crank sensors (that's the two wires you see coming out from the middle of the timing belt there's one on the crank and one on the top right cam you can't change the one on the crank without removing the timing belt) while I'm at it you should also replace the water pump just for good measure. It's easier to do all this if you remove the radiator fans and the radiator first.

[@jerbburleson1]

This is a very good video for illuminating those timing marks. I did indeed use cardboard under the crankshaft gear (reluctor gear) and that worked well. I also had the benefit of some Lisle Camshaft-Loks. Another thing I noticed and utilized for the sake of having another option than the camshaft-loks is that on the left set of camshaft pulleys if you will notice, just behind these camshaft pulleys are two threaded bolt holes on each(you can see one of these bolt holes in this video when he moves to the left set of camshafts). These bolt holes are metric M-8 size. I utilized these with some M-8 bolts and oversize washers to lock the left side camshafts on to their timing marks. The right side did not have the same type of configuration so I used the cam-lok there. I'm thinking though that you could pull this off without the cam-lok as that right side is pretty easy to get the belt started right on. I also used vice-grips to lightly press the belt into the pulley grooves and hold it while proceeding around the water pump and to the other set of camshaft pulleys. I also had benefit of a small inch-pound torque wrench and actual camshaft tensioning tool to set the manual tensioner to 40 inch-pounds as per instructions in a Asin Timing belt kit ordered from rockauto.com. 40 inch-pounds is not a lot of pressure and you can easily apply this pressure by using needle nose pliers in the two manual tensioner tensioning holes. I am reasonably mechanically inclined and had plenty of time to study and learn this procedure. If your in a pressure situation and do not have adequate resource or place to do this I might would hand it off to someone who does. I had a damaged and stuck crankshaft gear(reluctor gear) and next the C-key stuck in the crankshaft so it can be quite involved. I was sweating bullets on a couple of occassions.

[@djrennauto]

thank you!!!!! had so much trouble today doing this....was off by a couple of teeth...wont start...going back tomorrow to fix it right now that i saw this video!

[@Pono421]

Straight to the point and no BS 👍👍👌

[@jimmyhayes2826]

Dont try to pry the tensioner while in place, youll more than likely break the casting on the water pump or crank. If you can pry the tensioner back while attached to the block then you need a new tensioner anyway. Just simply unbolt it from engine and put it into a vice to compress it.

[@anthonyWayne76]

Oh no, i didnt.. i already have it compresseed with a c-clamp 👌😁

[@sidknee8490]

My timing belt has slipped twice now causing a knock (plenty of KZbin videos of same noise). The first time Beach sand got into the timing cover derailing the belt the second time the belt is loose and slipped again. Pulling it apart now to reset belt and hydrolic tensioner. Thanks for the tips..

[@amodestmousefan]

the mark on the crankshaft is in between two teeth everytime i get all the marks lined up the fin on the motor is either on the left or right side of it not sure if its supposed to be like that

[@BennyFatFingerz]

My man!

[@kristopherhasenbuhler5393]

Did half of mine til it got dark out Gonna see if I have the time to finish the job tomorrow.

[@hadihassan745]

Good job man tanks for , bat Can you adjust without tags and how?

[@adrianmtv7416]

I'm working on one right now and it tell me that the right bank (left bank if we look at it from front) Camshaft sprockets need to be 7.3 and 8.7 Pitch. What does that mean? Someone took off belt and now I'm trying to figure this out.

[@donlankford4315]

AdrianMTV did you get yours done. did you notice if your belt loosens after sitting for a few hours..

[@anthonyWayne76]

Am I suppose to here any "clicking" sound as I rotate the cams (ccw)?

[@BrianMitchell321]

Depends on what you're doing exactly

[@anthonyWayne76]

Was doing a water pump on my 05 sedona.. but the timing offset after removing the belt,..🤦‍♂️😡 so as i rotate one of the cams (ccw) i notice the crank is almost in alignment with its mark, but then i heard "3 clicks" sounds when the cam felt it didnt want to spin no further. 😬🤷‍♂️ (thys was done with an 17" open wrench")

[@BrianMitchell321]

I just seen this I wouldn't rotate the motor any further until you make sure it's in time your going to bend valves

[@anthonyWayne76]

@@BrianMitchell321 i was thinking the same thing 😕 .. so i just took it to my local shop. Thanks for the input though!! 👍

[@BrianMitchell321]

Best decision you could have made let me know how it went

[@peteryuanwordok]

May I ask how to pull the crankshaft pulley out after having removed center crankshaft pulley bolt ? Should I use a puller ?

[@BrianMitchell321]

Yuan Peter yes you almost always have to use a puller on most cars there are very few that you dont.

[@BrianMitchell321]

Yuan Peter actually if I remember correctly you don't need a puller you just need to wiggle it off there's only a 8th to 1/4 inch lip holding it on should be able to wiggle it back and forth and pop it off without a puller

[@peteryuanwordok]

Many thanks to you, Brain.

[@ramirocervantes9577]

Que fallas regular mente tienen la sorrento

[@BrianMitchell321]

English please no habla Espanol

[@rubengonzalez7376]

Ramiro Cervantes. Las misma que cualquier otro vehículo

[@fyireviewsandhowtos3118]

Here’s how I did my 2005 kzbin.info/www/bejne/hWOQqYB8r5iCmpI