How to synch up Camshaft Position Center with TDC when timing Ford 4.2 (This is a 2002 engine, from a 1997 truck)
Пікірлер: 29
@rogerblair8133 Жыл бұрын
Finally I found somebody to explain this in lame terms where I could understand it . I did the same thing pulled it out without marking it and I didn't paint my engine so I was lost until I seen your video. Thank u
@autotech2653 жыл бұрын
Great video, very well explained.
@garyjenkins66292 жыл бұрын
I'm still confused. I'm starting with a used motor with no synchronizer. How does this tool help me?
@Lxmustang8052 жыл бұрын
Thank you sir , we’ll explained .. a lot of these guys , can’t explain shit . This will help me a lot when installing this on a freshly rebuilt 3.8 ..
@DiezCallejeros2 жыл бұрын
i replaced it with the tool on but didnt put the timing in center dont know how to do that, its running fine but misfiring and turning off when im at stop and accelerate
@coreybabcock2023 Жыл бұрын
Yea I used the shape and curvature of the pigtail going to the sensor
@Badassbass7910 ай бұрын
I changed my syncronizer and sensor on my truck afew days ago.done everything u saud. But still on limp mode and says 340 on scanner.but the 2106 will pop on to but then i do it again it wobr show up only code 340.can u help me please???
@shawn011274 Жыл бұрын
Do you have to put cylinder 1 in TDC, before engaging tool?
@coreybabcock2023 Жыл бұрын
I pulled mine out to get at a bolt for the EGR stand pipe thing and put it back in based on how the pigtail going to it was and live data says 14 14.5 15 degrees advance timing so is it good or no ? My 98 Ford e250 with the 4.2 l V6 Essex engine
@dealerhealer3673 Жыл бұрын
Thank you very much sir
@rubbermallet38733 жыл бұрын
do you have the link for the tool you used to set timing on the 4.2 L?
What year engine? I've got a 2007 throwing a code for that sensor
@bgfixit3 жыл бұрын
This is a 2002 engine in a 1997 truck
@davidturney29753 жыл бұрын
So it should be similar to my engine then? Thank you
@matthewsempsrott64893 жыл бұрын
Can you replace the sensor without having to fool with the synchronizer?
@bgfixit3 жыл бұрын
Yes.
@bgfixit3 жыл бұрын
Yes, if just replacing the sensor. No problem, 2 screws, simple swap.
@ihulk13 жыл бұрын
@@bgfixit appreciate it my sensor just came in today so hopefully it does the trick.
@curtkellison3429 Жыл бұрын
What if ur sensor doesn't lift right up and off
@curtkellison3429 Жыл бұрын
Nevermind i found out why it was cracked and corroded inside
@ufartface3 жыл бұрын
there are 2 tdcs and what cylinder?
@bgfixit3 жыл бұрын
If you have to ask, you probably shouldn't be attempting this procedure.
@jciabatoni2 жыл бұрын
It's the 1st cylinder, front left. For future reference. Timing marks should be on damper/ counter balance wheel. And the block will also have a timing mark.
@lilchuy14852 жыл бұрын
Hi, what is the name of that tool, im about to replace my timing chain i i notice that censor so im a a stand still until i find that tool
@bgfixit2 жыл бұрын
Ford Timing Synchronizer
@bgfixit2 жыл бұрын
Or camshaft synchronizer alignment kit www.rockauto.com/en/catalog/ford,1997,f-150,4.2l+v6,1122455,ignition