Ford B-Max 1.0 Eco Boost Timing Belt Change Part 2

Hello and welcome
This episode on the ford b max 1.0 eco boost timing belt change part2 i found the pick up pipe blocked

[@giancarlorotter6331]

Great job on day 2 of the Eco Boost saga - love your energy and enthusiasm to get the job done and done properly

[@johnmcmahon4364]

Great video Mark, very informative and good advice. Make cars so difficult to work on these days you are doing a fantastic job

[@Bongybill]

Great to see how far you've come and the things you'll take on now. I've enjoyed watching the journey so far and looking forward to the road ahead. Will be a cracker car when you've finished and provide someone with trouble free motoring for a good few years.

[@ResurwreckAutosUK]

Thanks mate appreciate your support yeah definitely been a good journey so far nice one buddy 👍👍

[@martinfield1484]

Wow mark nothing would phase me 25 years ago but that is a tremendous amount of work hats off to you well done for giving it a go

[@ResurwreckAutosUK]

Thanks mate yeah I have been thinking of doing one of there’s for a while now 👍👍

[@MohdjesriOthman-oi1id]

Good work mate,you mark good job you repaired this b max mpv Ecoboost engine timing belt and water pump

[@ResurwreckAutosUK]

Thanks buddy 👍👍

[@cliveclive]

Well said Mark....terrific work your doing love every minute....But...there's always one......

[@juliancaston9598]

You're doing a great job mate. Personally speaking I wouldn't touch an ecoburst engine with a thousand foot bargepole..I will stick to my Mazda 2 1.5 skyactive G engine as its a non turbo chain driven engine

[@daviddominiak7790]

Great video Mark and wow what a lot of work it takes to do this job!! Bet you will be doing the next one tomorrow not 😂😂😂 lol!! Great job and it will be a lovely car when it's been all sorted with the small things that need to be done now! Stay safe and see you soon on the next one Mark

[@ResurwreckAutosUK]

Thanks buddy I’m really enjoying doing this definitely will do this again 👍👍

[@leebryan8976]

Well done mark getting there ,shame your locking kit hasn’t come ,I’ve seen people do it without on youtube . Lee

[@ResurwreckAutosUK]

Thanks mate yeah I had seen that video 👍👍

[@johnstevebs9756]

Well done Mark.great job your doing. I didn't no there was so muck work involved as I own one. but has been a great car but I'm worried.

[@ResurwreckAutosUK]

Thanks mate it’s a very big problem if you have a 1.0 ecoboost engine must get it cleaned out about 60k miles or 6 years old

[@johnmccarthy-jones1250]

What a bugger of a job well done for having a go.l think of i attempted it i would have to remove the subframe complete with the suspension and engine and gearbox so as to have full access to everything.

[@ResurwreckAutosUK]

Hi mate yeah definitely a pain probably be easier to pull the engine out 👍👍

[@malcallen695]

Great effort and content once again, 👍👍

[@nigelbryant5932]

Don’t buy another eco boom. Too much time and effort. Great progress 👍 enjoy your beer 🍺

[@ResurwreckAutosUK]

Hi mate I’m really enjoying doing this one 👍👍

[@Foton410]

19:35 actually, I saw in one video how they dismantle it and then you can take out the mesh. the question is whether it will hold well after this procedure. Due to this problem, I have an additional oil pressure sensor, not just a switch that says you have (some) or don't have oil pressure. Also pump have two modes most of time engine have 2 bar oil pressure and under load can get up to around 4 bar. Orginal pressure switch gives you a notification when pressure drop below 0.25bar but when oil pump is only partially blocked by pieces of the belt the pressure is reduced, but not so low that the switch detected it. And here we go oil starvation and engine after some time used in this condition is busted. I think typical owner do not know this until engine break up completely, when we get symptoms it's probably too late

[@peterfox6256]

I took one of those oil pumps apart once , had to press the drive pulley off to put it back together as had to put the inside bits in first then the cover

[@robertbowes1001]

As you know I worked at ford stealership and all I did/do is undo it with my Milwaukee m18 impact gun and to do it up I give it full send with lots of dugger duggers and never had a problem and I do these on my driveway on the side.

[@ResurwreckAutosUK]

Hi mate yeah the mechanic at the end has a Milwaukee m18 impact gun I’ll use that 👍👍

[@robertbowes1001]

@@ResurwreckAutosUK full charge battery and give it full send it will be ok.

[@danielsellers8538]

Some good pointers Mark certainly with the oil filter back up to the engine, it's more of peace of mind for you knowing it's been cleaned definitely a poor design. Your managing to complete other jobs whilst waiting for locking key to change cambelt & water pump a bit of advice use crectine to mark up with its what typists use on letters when they make a mistake small bottle with an application brush.. Excellent video 😊😊

[@ResurwreckAutosUK]

Thanks buddy appreciate the info mate 👍👍

[@themadcoachman]

No one Types letters printed by computer now ,I know you mean tip ex basically mate

[@danielsellers8538]

@themadcoachman l still type but then l. Old school

[@patrickh7368]

Another thing I’ve seen on KZbin is a cover that sealed a waterway with an O ring , on early versions the O ring can burst up like a breather hole and that’s why they lost coolant and overheat failure got them the ecoboom name, apparently that breather hole needs bunging up with a sealant to stop it occurring, allegedly the Ford mod, I don’t know enough about that but saw the video on KZbin where a mechanic stripped all the same off that you’ve done 😮

[@bt1804]

There were similar issue with the timing chain and the crank pulley bolt on the MG3 pre 2016 stop start

[@Love500]

This should make this car more valuable than a non cat car. As you said, if you buy a car even if someone has said this expensive job has been done, without evidence of a bill from a ford dealer, you would never know. They can look at this video as proof. In my book, this makes this a valuable car.

[@MartinJones-tl9kt]

Crank bolt you gotta have a torque multiplier to undo & tighten it not blow torch!? or a "bigger gun"

[@TimeTraveller3256]

I see 👀 thumbs up 👍

[@valvemonky4734]

there is some one who has shown this on youtube he used a powerfull air gun to get it off

[@JohnWilliams-tr7nw]

300nm for the crank bolt

[@JohnWilliams-tr7nw]

Or the crazy priced multiplier 😅

[@jstuart5430]

going to be a good car for some one when finished great way to sell with all the work showen online you might want to look at a dewalt or milwaukee 1/2 gun for crank bolts

[@ResurwreckAutosUK]

Thanks mate yeah I borrowed a Milwaukee gun to remove the bolt 👍👍

[@jstuart5430]

@@ResurwreckAutosUK good guns i m lucky to have both cant wait for engine rebuild and 1st start up video

[@etrell9553]

If you remove the oil cap, you can see whether the belt is still intact or worn out, but he's making the video he thinks will make him rich.

[@ResurwreckAutosUK]

🤣🤣🤣🤣

[@MohdjesriOthman-oi1id]

Ford main service dealer expensive charges to replace the cambelt and water pump and replace oil pump too

[@bt1804]

Loss of engine power and serious valve damage is commonplace on higher mileage EcoBoost engines.

[@jameswiglesworth5004]

Just quoted £1875 by Ford dealer to change cambelt and water pump on 1 litre ecoboost Focus

[@etrell9553]

The gasoline and its vapors damaged the belt, and the oil becomes contaminated with gasoline ?

[@joskd8491]

using the right oil should keep the oil from attacking the belt and clogging up the pickup. It's oil with the specification 'C948'

[@jonflounders1541]

Maybe ford should include a new oil pickup in the belt kit on the ecoboom engine would be cheaper than a brand new engine.

[@clivewright4398]

Eco boooooom. I pick wet belts and oll pumps and much more at parts plus. Bad idea having a nylon belt driving the oil pump. Best to avoid a higher mileage 3 cylinder ford. Well saved and it will keep the next owner happy when up and running.

[@ResurwreckAutosUK]

Thanks mate yeah definitely avoid the high mileage ones but this one will be a good one for someone 👍👍

[@TimeTraveller3256]

Blow torch on the crank bolt ? May help or maybe see if you can borrow a better impact gun (as in higher power Amps)

[@ResurwreckAutosUK]

Thanks mate appreciate the info let’s see how it goes 👍👍

[@tonyc2837]

The newer ecoboost engines have gone back to a chain apparently.

[@etrell9553]

But when you do the service, couldn't you remove the oil pan and then clean the filter that you see in the video dirty?

[@ResurwreckAutosUK]

That sounds so quick when you say it like that

[@etrell9553]

@@ResurwreckAutosUK "It might be faster than disassembling everything from above. If you remove the bottom pan, you can immediately see the filter with the metal shavings, and maybe understand that it's time to change the belt.

[@etrell9553]

@@ResurwreckAutosUK The solution is this: Oil Catch Can Kit.😅

[@MartinJones-tl9kt]

ECOBOOM! But no, the later engines are the same any engine with internal belt are a stupid idea fit a new pump or that strainer cap does come off, bolt pump back to engine & use a slide hammer with a hook & pull it then when clean tap it back in place seen it done

[@markhensby4352]

Hi Mark Who is going to spend £2k on a 10 year old car cam belt change? What a stupid design.

[@mrbond589]

How many miles has this got mate? Mines 52,000. Worries now 😮

[@ResurwreckAutosUK]

Hi mate 72k miles crazy 👍👍

[@expatliferealspain1175]

Now you know why they are called eco booms no one can afford to service them got to be the worst ford engine ever.

[@ResurwreckAutosUK]

Hi mate yeah you are so right 👍👍

[@TimeTraveller3256]

So the belt and pulley is submerged in the oil sump lol 😆

[@clivewright4398]

Eco booooom 😂. I pick no end of wet belts ,oil pumps, etc. The day in life of a parts plus picker. What a bad idea eco boost engines are..

[@TimeTraveller3256]

Haha 😮. Is this wet belt a common thing then or only specific to FORDS? You would imagine that a metal chain would have been a better idea for that design ?

[@clivewright4398]

Peugeot, have a similar problem!

[@WrenchingOnCars]

Lots of questionable design decisions. When you get the crank bolt off, you will notice there isn's a keyway for the sproket. How much would a timing chain, keyways of the crank and cam sprokets, and a front engine mount that bolts to the block cost?

[@ResurwreckAutosUK]

Hi mate you are so right how did this engine win so many awards 👍👍

[@stuwillis7710]

£1200-£1600 job. Is it worth it. ?? Puma speed sell a NEW ecoboost 1.0 for £2000

[@ResurwreckAutosUK]

Hi mate it’s crazy this engine 👍👍

[@stuwillis7710]

@@ResurwreckAutosUK But still is it easier to replace timing belt or engine ?? As an owner I mean

[@stewartdcampbell]

​@@stuwillis7710 if you do the belt yourself it's not going to cost anything like £1200-£1600 and if you're getting someone else to do it you're still going to have to pay someone to fit the engine.

[@satianable]

You spend far to much time talking.just get on with it.

[@ResurwreckAutosUK]

🤣🤣I’m explaining to the new owner not you 😂👍👍