GIVI PL3112 CAM Side Racks: Review & Installation

[@barkinsahin]

The black bolts Givi uses are not stainless steel (inox)!!! As you said, I replaced some...

[@paulwillis6969]

I am looking for racks to fit my 650 2019 model for soft panniers. I looked at the Givi racks but they don’t seem to pas the side of the exhaust fully. I haven’t found a producer that does this sort of rack that fully covers the side of the standard 650 exhaust. Shame.

[@jacobwilson4952]

Have you found a solution for this yet? I am in the same camp, looking to install soft pannier on my 2019.

[@roneningemeijnen5474]

has anybody found a solution for the soft panniers?

[@alcesspectre]

Good video but I'm pretty sure you doubled up on one of the small spacers. Bolt - washer - rack - large spacer - SMALL SPACER. That small spacer fits right into the bolt hole on the plastics and one was already there when you started, most likely from the top rack installation.

[@raymurphy2933]

Hi, can you tell me if the PL3112CAM side racks can be used with the Trekker Outback Alaska side boxes. Thank you

[@DrVstrom]

Pair of MONOKEY® Trekker Alaska side cases in natural aluminium, 36 litres, with identical keys and third cylinder to be mounted on any topcase. Equipped with MONOKEY® attachment system. It can only be mounted with the PL_ / PLR_ / PLO_MK / PLOR_MK side case holders. If you go here www.givi.it/per-la-tua-moto/product/suzuki/dl-650-v-strom-17--23/optionals/pl3112cam I can only compatibility with the evo and trekker outback. If I were you I would verify with them to make sure

[@raymurphy2933]

@@DrVstrom At 1:10 you say they are compatible with any monokey side case. This is actually incorrect as they are only compatible with the Givi Outback Trekker cases.

[@DrVstrom]

kzbin.info/www/bejne/fHzImZyAntSbn68 Yes they are compatible . Each bike will have its own specific side frame identified with a complete code (PLO___N) which will allow you to install different kits and, therefore, different models of GIVI side cases, from the MONOKEY, MONOKEY CAM SIDE, TREKKER OUTBACK hard cases to the GRT709 soft bags. The PL ONE-FIT specific to each motorcycle model will also exist already configured with the fixing system suited to the selected model of case.

[@raymurphy2933]

@@DrVstrom Just for anyone else buying boxes for this rack. The CAM racks are for the Givi Trekker Outback boxes only. The Givi Alaska or the Dolomiti will not fit on this rack as they are a 3 point mount where as the CAM Rack has a 4 point mounting system.

[@DrVstrom]

@@raymurphy2933 Check the adapter from GIVI and it might do the trick. In general its best to contact them to be certain.

[@markr8904]

This fellow does great work.I speed up the playback to 1.25 which works fine.His idea about the bubble rap is good.I lost a spacer before I watched the video.Also starting with the bottom bolts is good advice.I used a tiny piece of scotch tape to hold the spacer,washer and washer together which helped.Also the crossbar didn't fit.It was a few mm too long.I'm going to drill out and elongate the holes in the bar.

[@ChrisHenGaming]

I also got the problem with the crossbar. Everything else fits very tightly so I cant fathom that its just some bolts that are too tight. Probably gonna drill it out aswell.

[@2018NukNuk]

Hi, is the soft case not to close to the exhaust? You need the support from the lower horizontal bar i suppose? Thanks for all the helpful video's!

[@DrVstrom]

What soft case are you referring to?

[@2018NukNuk]

@@DrVstrom Any softcase.

[@DrVstrom]

No, it depends and you may need to adjust or not

[@raymurphy2933]

Thank you for this Video, It was a great help mounting the rack.👍

[@DrVstrom]

Glad it helped

[@KoHokCheung]

I have watched a few of your videos and they are really helpful. I am considering buying this rack for my bike. Do you know if it is harder for the passenger to access the seat?

[@DrVstrom]

Np its not harder. None of my passengers ever complained. But make sure that the side cases are compatible with the racks

[@TCDEWE]

Thank you so much for the video. It was very helpful 😊

[@DrVstrom]

You're welcome 😊

[@pete2109]

Thank you for taking the time and effort in producing this episode 👌👍 Did you complain to Givi about the bolts?🤔

[@DrVstrom]

Yes i did

[@pete2109]

Doctor Vstrom What did they say?🤔 Sorry? 🤷‍♂️ Did they offer you replacements? Or did you put your own stronger one’s in place? Thank you 👌👍🤘

[@DrVstrom]

Pete G yes I got replacement bolts

[@ZekovicMe]

Do you experience significant vibrations under seat around 5k when you revit in idle after mounting side racks? Now put both side panniers and vibrations are gone. Can you confirm is this behaviour the case on your vstrom please?

[@DrVstrom]

I dont experience that

[@ZekovicMe]

​​@@DrVstrom Well, i do when no panniers attached :( VIbrations stop when I remove cross pipe that connects side racks on rear. Also I noted that you put cross pipe on opposite side than shown in instructions manual. Wider hole for the nut on cross pipe should be on the opposite side of exhaust side. And the pipe is not symmetrical, it makes difference on which side you place the wider hole.

[@ivankriletic6553]

Have you solved the issue with the side rack vibrations and noise? I have the same issue. Thanks

[@DrVstrom]

Install like I did and you ll have no vibrations

[@ivankriletic6553]

@@DrVstrom I have. I double checked everything. I used the manual first that came with the rack, and second time following your steps.Everything is fix and strong. Only about 4.5-5 rpm i feel vibrations on seat and noise like buzzing.Same hapens when revving in idle . I looked up and it seems a common problem with givi recks and v stroms.but no one seems to have a clue.

[@long_vacation_tour]

Thank you for the video. Can you tell me where did you buy fuel tank stickers? I would like to buy the same.

[@DrVstrom]

www.amazon.co.uk/gp/product/B074XCNJ26/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

[@long_vacation_tour]

@@DrVstrom Thank you very much 🙏

[@hugocrites2075]

Can you remove the silver part (where GIVI logo is located)? I ask because I want to use the round bar instead of the GIVI specific attachment. great video thanks!

[@DrVstrom]

Hugo Crites yes it is removable

[@volt8684]

Excellent thanks awaiting delivery of mine

[@DrVstrom]

Great 👍

[@volt8684]

Hi watching this again would u use thread lock please?

[@DrVstrom]

No, not really. It would not make a difference. It's not that the screw will come out rather it may break

[@volt8684]

@@DrVstromfitted today thanks for this video especially which bolts to start with if fitting alone. If there were two people I’d put all bolts in together as hard to get the “inside” fittings right. Have to say disappointed with the quality including the panniers and locks. My yamaha fjr 1300 luggage came with bike was superb and tough. Love ur channel. I have great difficulty undoing axle nut even though use torque wrench to tighten. Great tip about coolant pipe rubbin on nearside too. Thanks you sir!

[@DrVstrom]

Check my video where I stress that you need to put anti seize compound and torque bit lower kzbin.info/www/bejne/invMZZlse7p7Y6s 23:25 Proper Way to Tight the Rear Axle Nut

[@arishdeva9741]

Καλησπερα, Συγχαρητηρια για τα κατατοπιστικοτατα βιντεο, Γραφω εδω γιατι δεν ειδα καποιο σχετικο βιντεο.Θελω να βαλω αποστατες στο τιμονι ενος vstrom 650 2018 γιατι το νιωθω λιγο χαμηλο και μακρια απο το σωμα μου. Θελω την αποψη σου εαν εχεις εμπειρια πανω σε αυτο και εαν ναι εαν εχεις να προτεινεις καποιους συγκεκριμενους. Ευχαριστω και παλι.

[@DrVstrom]

κσπερα, ευχαριστω. Δεν εχω βαλει αποστατες. Πρεπει να προσεξεις να παρεις αυτους που θα φτανουν τα καλωδια μετα.

[@arishdeva9741]

@@DrVstrom Ευχαριστω για την απαντηση..εχω δει καποιους με 3εκ υψος διαφορά απο το κανονικο...πιστευεις οτι θα ειναι οκ με τα καλωδια?

[@DrVstrom]

Οι περισσοτεροι θελουν αλλα σωληνακια. Αυτοι ισως οχι www.amazon.com/dp/B071CX5L57/ref=cm_sw_em_r_mt_dp_U__hfC5BbGVHZH50

[@MrKaytje19]

Can you show how to change a headlight?

[@DrVstrom]

Its not in my immediate filming plans but I can help you do it if you tell me which model and what exactly you want to do

[@MrKaytje19]

Doctor Vstrom hii, no problem! I have a Suzuki Vstrom dl650 2017.

[@DrVstrom]

MrKaytje19 Please sent an email at [e-mail] so I can reply back with instructions

[@adamm5549]

I am trying to do this myself. However my Vstrom has the hooks for the factory cases which are in the way of the rack. What am I supposed to do about that? Cut them off?

[@adamm5549]

Never mind, I figured it out. It comes with different spacers so the plastic bit that mounts the factory cases can be eliminated entirely.

[@DrVstrom]

Can you sent me a photo of the hooks so I know what you mean?

[@DrVstrom]

@@adamm5549 Yes exactly

[@adida236]

I have the same problem but I did buy the oem plastic covers whitout the hooks actualy they are called frame cover rear left and right, and about 11€ for both

[@HipsterLan]

Really useful and helpful to me. Thanks a lot

[@DrVstrom]

藍紹綸 thanks also :)

[@ricardovelazquez1650]

Gloves ??? What ladie

[@DrVstrom]

Question?