Go Kart Reverse Assembly Install

[@jakewilliams4990]

Brilliant. I wish all how-to videos were like this.

[@troybloomfield6999]

Good explanation no monologue just started

[@TheXrunner79]

Where can u get spacer different size? I just replace my my engine and the reverse box deeper than the original engine.

[@scooterboy304]

Very good video.it was hard to find a detailed video of the installation.thanks for your help

[@buildurtruckurway9118]

Do you guys have a link to the gearbox.? My sons atv has the fnr rear axle instead and I’m looking to change it to the gearbox like this one instead.

[@lloydmorrisonii1373]

Outstanding video!! Very helpful.

[@covertprepper5957]

So that main bolt on the spline is the only thing holding it on? I have an old one I'm pulling off an old motor and it won't budge. I can't figure out if I'm doing something wrong.

[@bosz6907]

Where can I get a kit like that van you help me please thank yoy

[@joshwilliams5229]

I just installed this reverse module into my hammerhead twister, it goes into reverse but won't come out. Any ideas?

[@kennethrand1032]

will that reverse unit work with older carters with the short case gy6 and long output shaft?

[@GoPowerSports]

I've seen 300 lbs get pulled up a mountain on this bike

[@kennethrand1032]

@@GoPowerSports that's great but will the splines match up?

[@rikityrik]

Is the adjustable cap you showed available at your store? I’ve looked and looked but can’t find anything. If so would you please provide the link? Thanks.

[@zelmagrooms7435]

i have replaced the carb on my tomberlin crossfire 150. it running kinda sluggish, i tried to adjust the carb at idle is fine but as im driving it seems to lag in power. speed and take off. what could be the cause of that??

[@night_shade1x]

I have a maxxam 150 2p that I replaced the cable on and it still wont go into reverse I have tried adjusting it and nothing is working it was working before the cable broke need some assistance please!

[@samiamm5764]

Am I able to purchase that sleeve where the reverse cable screws into? I bought a hammerhead that’s missing the cable and sleeve. Will a cable replacement kit include the sleeve?

[@lukasjansen4632]

how does that thing names that goes over the cable and the ball?? I need it but can't find it

[@TheMikeawesome88]

Whats the new castle nut size you used?

[@albertopitre2433]

Where we buy the gearboxxx???

[@rickyflippo8552]

Do that engine work on a carbide 150cc GY6 dune buggy ???

[@leonmcelrathiii2429]

What happens if you don’t hook the reverse up?

[@hugofigueroa7619]

Can you tell me what size bearing goes in the outer casing

[@majmyguy6254]

Why does my reverse assembly get extremely hot after on a couple of minutes of regular riding, not full throttle?

[@mikeanderson2255]

can that forward reverse assy. be modified a bit to work on a manco 606 frame with a 6.5 robin /subaru motor and a series 30 comet torque converter. I have been looking at the comet forward/ reverse gear assembly, but if this works it is about 1/2 the cost. What do you think? or does go powersport carry the Comet forward /reverse. Of course I would also need all of the mounting brackets, cables, hardware and lever. Any advise?

[@leonmcelrathiii2429]

I recently purchased a used hammerhead go kart. Every time I start it, it moves forward. Can you tell me how to fix that

[@redashphoenix]

Turn back idle screw rpms are to high causing movement

[@LuisGarcia-so1kk]

Were can i order the reverse kit

[@jeffrosoupy]

I put the same reverse assembly on my gts 150, goes in drive and when I pull The handle it’s like it goes into neutral but doesn’t go into reverse, trying to figure out if something is messing inside. because I was giving it when I bought the hammerhead, I know the external reverse came apart maybe something isn’t aligning up inside to kick it into reverse.

[@futuregamer5791]

Ever figure your problem out? I have the same problem

[@davidhayes7688]

I have a 150cc (147cc displacement) Chinese brand dune buggy. The reverse setup looks just like the one in the video. Is their supposed to be play on the backside of the reverse box, Between the reverse box and the motor? I'm trying to determine if it's broken, because I've been having an issue with getting it to stay in gear. I installed a new cable and it works fine as long as I squeeze it together with my hands. Any help would be appreciated. Thanks for reading.

[@MrFinkFixes]

What do you do if the Reverse assembly is fused to the output shaft?

[@ginzwest2848]

Did you ever get an answer? Please say yes lol

[@poodull76]

What is this make and model. I think it is what I have, but the previous owner didn't know.

[@waugzoo1]

whats the model of the buggy you are working on? thanks great video.

[@bosz6907]

Thank you

[@GoPowerSports]

You're welcome

[@joshackman6375]

when i installed it has a wobble and everything was tight no loose bearing....

[@gtyouth4340]

Can reverse go on a predator 212cc ?

[@mikemoore466]

GT YOUTH There is a reverse kit that will work on a 212cc predator. It is on EBay for about $160.

[@tonysmokes722]

How to install reverse gear box

[@LuisRuiz-yl4pi]

I have a carter Talon 150 but when I put it in reverse it makes a loud clacking noise what can I do ??

[@MilesPrower1992]

Wear earplugs

[@madewidiarta2496]

Dimana bisa beli