iPhone 5G Antenna Replacement

[@smoothlarryhughes]

where does the other end of the antenna wire connect? I was taking the motherboard out of an iphone 13 pro and tore the same flat cable.

[@LILGRIZZLY]

What kind of flux you to make the Antenna stick specifically please im trying to do my own repair iron Good video btw

[@GoCellPhoneRepair]

I'm using 2UUL from Union Repair at the moment but note that the flux is only on the outside of the antenna connector. The pads underneath will still bond and I don't apply it there to prevent it from slipping around. I've used Mechanic 225, Kingbo, Amtech... all of them work just fine.

[@LILGRIZZLY]

Thank you

[@Thomas-Magnier-Ferreira7]

Where are tests points ? Thanks !

[@inderjeetuppal6462]

Does it work in other countries like India, uk these 5mm uw antenna flex?

[@GoCellPhoneRepair]

As far as I know it is mainly in the US and almost exclusive to high density events like concerts, athletics games, etc.

[@inderjeetuppal6462]

@@GoCellPhoneRepair high density as in?

[@GoCellPhoneRepair]

An exceptionally large number of devices connecting to a single tower.

[@RealWorldReview]

Not a fan of that connecter to solder. The iPhone 14 Pro Max Bluetooth antenna is soldered the same way and it’s a pain to fix if you accidentally add too much heat when fixing the back glass😅

[@GoCellPhoneRepair]

Yeah, strange way to do it in my opinion.

[@omodelesalu]

When its ripped, does the phone still get 4G network? Or do you have to replace it to get 4G network?

[@GoCellPhoneRepair]

You should still get 4G and in many cases 5G can still function. This antenna is strictly for millimeter wave 5G that you will find in crowded areas like airports.

[@TheAverageG4mer]

Will this fix my cellular issue on my iPhone 14 pro ? It’s stuck on searching and no service, when I go to setting and click cellular It says Error?

[@GoCellPhoneRepair]

Check settings>general>about and scroll down to modem firmware. There should be a version number there. If not, you have bigger problems, like a bad baseband pmic or some fractured solder joints. The 5G antenna only picks up UW frequency and should not prevent service altogether.

[@shadynumbers8561]

How much do you charge for this exact job?

[@GoCellPhoneRepair]

If you haven't already, please contact me here gocellphonerepair.com/contact/ for pricing information.

[@nelzaecaasi3915]

Hello. Do you think same diode values in Iphone 14 pro max

[@GoCellPhoneRepair]

I believe so.

[@LILGRIZZLY]

Hello had the soldering iron at 400 C didn't want to stick please what flux you use not on the outside of the pads but on the inside the small square ⬜⬜⬜⬜ ⬜⬜⬜⬜ ⬜⬜⬜⬜ Im doing this right now but the 5G Antenna Wont Stick the to the small boxes ⬜ please help

[@GoCellPhoneRepair]

I have my soldering iron at 840 F so that might be why it was a little easier for me. The flux is only on the outside of the antenna as I found it too difficult to prevent it from sliding around when there was flux underneath. That said, I think that any decent SMD flux should work in this situation.

[@GoCellPhoneRepair]

*840F.

[@MazenNour-n4l]

is a value of .70 instead of .59 okay?

[@GoCellPhoneRepair]

Sounds close enough. There will be some variance based on different meters.

[@mazennour9515]

Why don't you use the heat gun?

[@GoCellPhoneRepair]

It’s pretty easy with the iron and anytime I can avoid heating the bottom board I do so because the components on the other side are very sensitive. Using hot air would radiate more to the other internals.

[@jimutreang3812]

You can fick my ipad motherboard daed