How I fit ENGINEERED OAK wood flooring

[@GosforthHandyman]

In case KZbin breaks, please join my free mailing list: gosforthhandyman.com/newsletter/ Be part of the Member Zone community: members.gosforthhandyman.com

[@markrowland5393]

Done!

[@paulwhitemore1801]

Hi Andy tried joining your mailing list but just keeps coming up site not available?

[@markrowland5393]

@@paulwhitemore1801 It seems to be working now. I've just tried it.

[@paulwhitemore1801]

@@markrowland5393 no its not tried again says rebrandly not responding!

[@GosforthHandyman]

@@paulwhitemore1801 Strange - try the link from here gosforthhandyman.com/newsletter/

[@AndrewCoakley]

If only you'd made this a few months ago, before I started fitting my engineered wooden floor! Despite watching so many videos about this task, not one of them got into the nitty gritty of checking the room squareness properly before starting. You've devoted so much time to it (the right amount of time!), and it's a crucial consideration - particularly here in the UK where squareness can sometimes be nothing but a dream. I've fitted my floor to the point where I realised that the whole thing is out of true because the wall I started on isn't parallel to the others. So that's where it's stopped - with a lounge floor that's in but skew, and unfinished. I'm building up the will to go back and sort it out as best I can, and it was genuinely hard for me to click the play button on this video as I knew you'd do it properly, and I'd have to eat some crow. Thanks for putting out the best video I've seen on this topic - I'm sure it'll help others avoid this painful lesson! PS: another issue I found after the fact is the subfloor not being flat. It has dips and bows all over the place which are not obvious with carpet and underlay on top, but very obvious when walking on the floorboards spanning over these dips. Maybe this'll help someone that's read this far down in the comments. Needless to say the floor is going to have to be lifted so that I can shim these areas and correct the squareness...

[@apmeehan]

Ah man, I couldn't relate more. Sending solidarity, and hope you eventually managed to summon the motivation to go back and sort it!

[@Isabel-of4wq]

Thanks for your feedback that’s so SO helpful for other newbies like me! I hope you get it all resolved to your liking

[@spacecraftbuildingservices]

Hi. Have just layed about 23m2 in a house very similar to yours. I posted some time ago to say how helpful your vid was and I can now say absolutely that it was. The importance of getting the line bang on that long run cannot be overstated and continually checking for adjustment if needed. My flooring was mixed in the sense that some of the grooves were rough. I developed a habit of clearing each groove with a screwdriver blade before gluing and it significantly reduced the need for excessive hammering. Thanks again. Jim

[@tomdarling-fernley3178]

Phew, good for you on being way more philosophical about that hearth install than I'd have been! I'd have been raging.

[@Czechbound]

That was great ! Very "real world". I think for the risk involved for an amateur ( in my case ) installation vs 2 1/2 grand labour spend, I'd certainly give it a go. If I ended up scrapping a couple of packs, I'd still be able to convert a lot of that saving in labour into tools that could then be used in other jobs. It's laying a floor after all. Not sending a rocket to the moon. Measure twice, cut once, and have it all planned as you showed us at the beginning of the video is really great advice !

[@theofarmmanager267]

We are just completing a large barn conversion. Had many, many trades and suppliers in during that time and they fall very distinctly into 2 groups - ones who had little knowledge, lots of BS and just wanted full pay for a lousy job; then there were those worth their weight in gold because they cared. Sometimes they were cheaper; sometimes more expensive but within a day I learnt to tell which camp the tradesman came from. I don’t know much about building, plumbing, electrics - really just as much as most people who have done a lot of DIY; I’m therefore susceptible to hearing what turns out to be crap. Right from the steel frame manufacturer at the beginning to some plumbers doing 2nd fix at the end, we have had people in who I’d like to throttle. A little surprising to me, everyone whose name I got from Checkatrade, as opposed to recommendation from another tradesman, has tuned out to be very good. We had about 90square metres of herringbone click system engineered oak. Don’t. It took twice to fit as long as glued herringbone; no benefit in the click system and the professional layers seem to hate it. Shop around; we bought our oak from one firm who thought we were silly enough to think we would add on the gold underlay as an afterthought. Just a little shopping around and we saved hundreds. I could wrote a book on renewable energy suppliers. That sector seems to be attracting all the cowboys; all the chances; all the con men around. Our first supplier went bust (seems a regular occurrence on this sector); finding a reputable one is a real headache. There are those who demand high deposits - but beware; giving a company a deposit is lending them money; would you lend money without checking somebody out? I’m lucky in that I can read company accounts but heaven help those who can’t.

[@alexc6414]

I cannot believe how far the renovation has come. I remember when I first saw it, I couldn't believe that one man and his wife would be able to fix it up in a reasonable amount of time. Incredibly impressive.

[@ottochristensen4841]

It's a great job, with good and understandable instructions.

[@roberthardy2013]

Great job Andy, don’t you just love how multitools make this sort of job easier.

[@GosforthHandyman]

Too right! Much neater job too. 👍

[@ElevatedJamTracks]

Just ordered a tape measure - Wore mine out recently on a landscaping/porcelain patio project! Love the content mate, been a fan for a while. You have a habit of uploading a video not long after I've done a similar project and showing me how much better I could have done it 😂

[@stuartlockwood9645]

Hi Andy, you did a great job mate, and Mrs Mac wiping off the glue must have Been a big help, I did vertually the same job for one of my daughters a few years ago, large through lounge and hallway, same type of flooring, it took 3 days, at the end of each day we put flooring ratchet straps across the unfinished floor to keep it all tight, worked a treat. Same method of fitting as you did, fully floating, and it's never moved, phew!,lol. My daughter selected all the boards from the packs to achieve a nice spread of tones, that speeded the job up no end. Thanks for another interesting video mate, best wishe's to you and your's, Stuart UK.

[@GosforthHandyman]

Cheers Stuart! Yeah, defo helps if you have someone sorting the boards for you too! 👍

[@normanboyes4983]

Well Andy, I was absolutely floored to see you doing this but was not board at all.😉 You did a cracking job as usual, you are right, it is murder on the knees and the back and as you get older once you get down on the floor you sort of think is there anything else I need to do down here before I get up. I read some of the comments with respect to floating floors and the weight of the fitted kitchen likely causing problems. I agree with you the way you have done it - there should not be a problem. The only risk is water leaks and you could take a sort of preventative measure using a water leak device - Honeywell do them and Sure Stop do one that will also shut off the water supply. 😀👍

[@lukepowell4953]

You've come through for me again! Tax returns, to drainage and now flooring, you're voice is that of reassurance!

[@jacopo.scarpellini]

Looking forward to the skirting board fitting; I have done a similar installation on a floating floor across 3 bedrooms and a hallway with no thresholds; my engineered wood floor is a click type, but I've glued the joints with PVA to minimise creaks; it was all sound and solid until I fitted the skirting boards, then it started to be sensitive to temperature changes, i.e. when you step close to the skirting board, it creaks as if you're breaking the friction in between the floor and the skirting

[@eurogeordie]

Just laid same flooring in my conservatory, last March. Never having done it before, i watched loads of youtube videos on laying this stuff and not one of them mentioned using glue on the tongues, wish they had. I live near Folkestone in Kent, but when i was a kid i used to play in that stream at the bottom of your garden, when i wasn`t nicking golf balls from the golf course. Ian

[@GosforthHandyman]

Ha that's great! Lots of golf balls in the stream! 😁👍

[@rmca11]

How's it holding up after using the floating floor method? Any bowing at all after the 1 year of temperature fluctuations?

[@keithgarrett42]

I love that you have a metric/metric tape measure. I was so happy when I got mine!

[@Gerry2210]

You and Mrs Mac are both doing a marvelous job all round the house. 👍👍

[@GosforthHandyman]

Cheers - nearly done!

[@rubbersteve123]

Excellent advice and finish oak flooring. We'll done.

[@GosforthHandyman]

Cheers!

[@whizwest2661]

Great video, I’m soon to take on a Bungalow with similar engineered wood. I’m just a diy-er but after your excellent guide, I feel I can take it on. Thank you.

[@raydriver7300]

I took half my workshop, including a DeWalt flip saw, to France in 2017 to lay my son’s laminate floor and left a box with my drill and screw driver behind. I now have two of each! As always, Andy, great video and thank you for sharing 🌞

[@GosforthHandyman]

You can never have too many drills though! 😂 Cheers Ray! 😎

[@louise5651]

7 minutes in and I can't stop thinking about that fireplace being on the wonk - I'm fuming for you :D

[@GosforthHandyman]

Yup, hadn't even noticed before this! 😂🙄

[@tomsimpson3322]

Top work as usual Andy. Bottom of stairs looks brilliant👍🏻😉🏴󠁧󠁢󠁳󠁣󠁴󠁿

[@GosforthHandyman]

Cheers - really pleased with how it came out around the stairs. 👍

[@stum7396]

Great video as always! Does anyone know how I could replicate the blocks Andy screws down to keep the reference row straight on a concrete sub floor? Got to do it next week!

[@corneliusencyclopedia39]

Looking nice Andy. Couldn't help but notice the Aviano 8 speakers and the Slayer LP. Good lad!

[@GosforthHandyman]

Oh yes! They're the 6's - Slayer sounds awesome through them. 🤘

[@terrytopliss9506]

The floors look really professional Andy.👍👍

[@GosforthHandyman]

Thanks Terry - really pleased with it. 👍

[@JordanUK99]

Decent job that, I’m a floor layer and can’t really point out anything wrong with it. Are you using stop ends or scotia to cover your expansion gaps? Also I clamp the flooring every 3 rows, just helps to keep it in bond and stop any movement whilst laying

[@GosforthHandyman]

Cheers! It'll just be flat oak trim (rounded edge) - not a fan of scotia. 👍

[@JordanUK99]

@@GosforthHandyman good decision, I’m really not a fan of scotia either

[@disgruntled4298]

Scotia is good if you paint it the same colour as the skirts because the colour goes to the floor and the eye isn’t drawn to the colour coming up from the floor which in my opinion is unnatural. Btw been laying floors since 97. Also in the glue point if you do the glue in four inches squeeze, four inches of void you very rarely need to clean up any over spill and there’s enough to hold the bond, I also clamp up every four or five rows.

[@olivermansfield8341]

Why not put under skirts as they're not fitted yet? That's what id normally do

[@hunterreed1010]

@@disgruntled4298 clamp how please? Special clamp?

[@oliverking9951]

Looks fantastic! New flooring makes such a massive visual difference. You must be well chuffed. Great video, as always!

[@GosforthHandyman]

Too right - cheers bud!

[@paulmoy9736]

Absolutely amazing job Andy......I've done a similar job to this and it's an absolute killer on the knees and the back.....Well done !!

[@GosforthHandyman]

Cheers Paul!

[@felixreali7101]

Andy, the floor looks amazing. Great choice of wood. And you gave some smashing tips for laying this down.

[@GosforthHandyman]

Cheers Felix!

[@notreallyhere1136]

I’m not an expert at all but my harth was on the wonk. My house is well over 100 years old. When I did mine I installed the second to last row and scribed the harth with an off cut onto it. I then cut that piece out and replaced it with a new one. Looks mint and no scotia/ covering required. Been installed 2 years with no problems

[@GosforthHandyman]

Nice one! 😎

[@BertieBarbel]

Great video so after 2 years have you had any problems with the flooring having laid your kitchen on top of it? I've just had the same flooring laid on a very solid levelled floor and about to put the kitchen in, the flooring supplier said that if the kitchen is laid directly onto the flooring it invalidates the warranty. My floor was full contact glued directly to the self levelled floor fitted by professional flooring contractor. Any advise much appreciated because I really don't want to take the precaution of cutting 50mm holes where the feet go if it's not necessary.

[@sarahmangone7785]

AWESOME! I watched another video and then came across yours and it was much more informative. I love the idea of using glue vs nailing.

[@stuarth540]

Where did you get the underlay from for the flooring.

[@kroneditor9266]

Great job! Loving the videos of the whole project and wishing you all, the very best with it.

[@GosforthHandyman]

Thank you!

[@debonh3828]

A number of years ago, I laid a clip together engineered wood floor, same sort of area as yourself, two or three connected rooms. It's been fine. Only problem, the old coal fired boiler leaked, and has been replaced, but the rusty water stained the boards and warped and separated the edges of the veneers. I have enough planks left over if I'm careful, to replace the damaged parts, but a rug has covered it for the past five years or so... In your case, I'd definitely do the utility room, and anywhere else.

[@GosforthHandyman]

Oh no! Hope you get it sorted. Cheers!

[@johnclose2323]

Great Job as usual. With the engineered oak instructions I fitted it said run a line of glue along the top edge of the groove. I stood each length on the floor on the tongue and with groove up over ran the glue along the top edge. When fitting It seemed to have less squeeze out. Any awkward areas of the room I would lightly sand the groove and the tongue to remove any woodchips so they would go together easier to save any hassle. The ends of the wood seemed to be the worst. When using the utility bar to lever the wood together near the wall I had a old bit of aluminium plate to put against the wall to protect the plasterboard.

[@GosforthHandyman]

Nice one! 👍

[@destinyangel5]

Great video Im just about to do my 33 sqmetr floor on top of concrete slab. I like how you went floating and used the underlay then lay boards straight on top of underlay and didn't do glue down , I guess because you glue the joints with PVA wood glue this makes it act as one giant piece of wood and the weight holds it down and stops and spongy feeling when walking on it , so it feels like its solid glued anyway without the hassle of using drums of flooring glue . Can you advise please on your results and how the floor feels to walk on now ? thank you .

[@martynbuzzing3327]

You make it look so easy. I've got a similar job to do. Great advice, thanks.

[@GosforthHandyman]

Cheers! Not too bad, just take your time with it. 👍

[@kevinbolton2738]

Andy, your timing is perfect! This was uploaded on the morning the other half wanted to go and buy an engineered wooden herringbone floor for our lounge. As usual, after watching one of your videos, I exclaimed in the shop "I'm not paying that for fitting! I reckon I can do that, Andy's video made it look pretty straightforward." Wish me luck... As a relative novice, it was eye opening to see what you need to take into consideration when choosing and preparing the floor. As an old Edwardian house we can't get the original skirtings off, but the multitool trick will be invaluable around all the decorative door frames and mouldings. I'm debating whether it's worth using the multi-tool to cut the bottom of the skirtings off to slide the floor underneath, instead of a quadrant trim painted to match the skirting. Is that asking for trouble? You've also sold me on T&G as especially with herringbone, it's going to be much easier to tap into place around all those awkward corners. Cheers Andy, great video as always!

[@mtthewd]

How did this go? Herringbone engineered wood as a DIY job is not something I would attempt, even as someone who's layed laminate vinyls and carpet in the past.

[@JohnJones-wo1bc]

Awesome job. Really enjoyed the tips and tricks to do it right.

[@Scorpio_moon74]

I wished you lived near me. I'm looking for a carpenter to fit internal french doors and new frame, and no one is interested! The last carpenter made a real mess of it 😔 The floor looks beautiful. You are so talented 😍

[@GosforthHandyman]

Thank you! Hope you get sorted!

[@spacecraftbuildingservices]

Really helpful video. Thank you. I'm about to embark on the same in a similar layout. Can I ask a few questions please? 1. What thickness was your oak boards? 2. How did you get confident that the levels in different areas weren't so different as to pose a problem as you worked through? 3. I've got wooden suspended floor changing to concrete floor in both the rooms I'm proposing to floor. Looks like you had something similar but in your extension you seemed to have some sheet material down. Was this to level up please? Great vid. Thanks Jim

[@idlersdream826]

Very nice job Andy 👍. I’ve become a fan of Quickstep Livyn Vinyl plank flooring over recent years in our home, easy to lay as it’s flexible for the more difficult areas, can be scored with a knife so no power tools needed.

[@micdev42]

Superb job and beautiful music.

[@hippiemark01]

I'm about to do a similar job and have a couple of questions. I'm looking to use solid wood rather than engineered, did you sand the floor once it was done? Also why floating floor rather than sticky backed underlay?

[@robwilkie1]

Andy - love watching your videos but why on earth did you bring those cables up through the floor instead of up the walls and into sockets that you could then have plugged into.

[@GosforthHandyman]

Ha, that would be very, very low on the priority list of everything that needs doing to this house. 😂👍

[@alexspencer84]

Thanks so much for uploading this and going into so much detail. Loved to see the Reign in Blood vinyl 🤘🏻

[@bencampbell198]

That was deeply satisfying to watch

[@darrenpaulgreen]

Hi Andy, lovely job. I’m in Yorkshire and wouldn’t charge less than £2.5k as you mentioned. My only query would be running the flooring under the kitchen units, as most manufacturers don’t recommend it as the weight of the kitchen (allegedly) stops the floor from expanding and contracting, invalidating any warranty. Now I’d argue that freestanding appliances also stop this from happening and aren’t prohibited, but I’ve had one instance where the client insisted running the floor under the kitchen and we did experience some bowing of the floor and the manufacturer wouldn’t cover it under their warranty. Now in this instance I think this had more to do with inherent damp issues in the property. Would be interested in your thoughts though.

[@GosforthHandyman]

You just need to design the kitchen to allow for it. As you say with free standing appliances there's not much weight in the cabinets. 👍

[@firesurfer]

Most people put cabinets in after the floor. It's a royal pain fitting cabinets otherwise. When a cabinet has to be moved in case of a leak, there are major issues. Especially with stone countertops.

[@bellabella9918]

You did a wonderful job, it looks fab!

[@GosforthHandyman]

Cheers!

[@garyglennon2566]

Hi Andy, great video as I'm just about to start laying the same type of flooring this week. Can I ask what type/name of underlay you used? Cheers Gary

[@sb-s395]

Nice shot of Reign in blood there. I do love that album.

[@GosforthHandyman]

Great album - seen them live several times 🤘

[@Sortitoutman]

Like that flooring! What colour is it / link to where you got it if possible? thanks

[@brentfrench752]

The floor looks great, but of course everything you’ve done looks great. I like your view of the backyard, or garden as you lad’s call it. Very serene and peaceful. I saw your wife helping you with the floor for a bit, but I’m sure things would have been easier if you had a second person cleaning up the glue and doing all the cuts. Appears to be a slow tedious job laying floors. I’ve always wanted to buy distressed homes, fix them up and resale, or rent them. Unfortunately, when I could do it, I was broke, and now that I can afford it, I’m too close to retirement to risk any money. Look forward to seeing the before and after video when everything’s completed!

[@GosforthHandyman]

Cheers! On to the decorating now so hopefully not too long for the final reveals! 😁

[@robthewaywardwoodworker9956]

Looks great, Andy. Are you going to build a little bench seat (instead of a box) in that alcove to hide the telcomm bits? It could have a flip top lid. Just a thought. Cheers.

[@GosforthHandyman]

Cheers! Yeah, something like that. Haven't worked that bit out yet. 😁

[@michaelveddah8028]

Great Video, love the banter, where did you get the Engineered Oak Flooring from? Cheers

[@fretwell2k7]

Looks great! Where did you source the flooring from ?

[@robertgeiger2268]

Good choice on music!

[@GosforthHandyman]

👍👍

[@michaelevans1658]

Good job Andy .

[@johnferrol743]

Can you give me the name of the flooring you used,it looks great

[@DerekTJ]

I left the glue in a bucket of hot water and it flowed mych better. Very annoying to be slowed down by such a minor issue. My floor lengths were 1.9m, so had to fight against the tongues edging back out of groove; i used long clamps, combined with nylon cord to squeeze them in - hammering them in wasn't enough. I also screwed blocks on the working side as i went.

[@mphys5370]

what did you do at the Bifold door floor interface?

[@GaryThomsonJoinery]

Beautiful Andy, thanks for sharing, I normally can’t walk properly for a few days after doing a floor. 😄🔨📐👍

[@eldoradocraftsman3733]

That’s a top job and I look forward to the end result. Regarding cost of fitting. I was thinking the same. £2,500 plus Easily. 👍🏾

[@SteveAndAlexBuild]

Lovely job , nicely done 👌🏼🧱👍🏼

[@GosforthHandyman]

Cheers Steve! Hope you and yours are well! 👍😎

[@SteveAndAlexBuild]

@@GosforthHandyman . All good thanks 🧱👍🏽

[@buildatrap]

Hi there, do you know what brand the underlay you used is?

[@benwest7780]

Slayer!!!!! Yes mate! Great video also.

[@FcoAyusoSuero]

@Gosforth Handyman I am going to lay down LTV on top of my floorboards lke yours. I see my floorboards are not fully screeded so I was wondering if your floorboards were totally screeded. I have the hallway of the house with laminate floor and there is some squeaks....would engineering wood resolve all the squeaks even if the floorboards are not screeded? Thank you a lot

[@GinasWorld9]

Hi, my subfloor is concrete covered with tile. How might I fix my plumb line/stop blocks?

[@paulstoddart7325]

i installed a floor like these years ago in my hallway. not sure if it was because its a narrow space but over time the floor moved and there are now gaps in the joins even though they were glued. always thought i should have nailed it. what did i do wrong?

[@geoffhayday6003]

Looks great. I did one of these and bought a couple of ratchet clamps, which helped though I stopped to let the glue go off after 3 or 4 rows. Looks like I need not have by this!

[@madeincrayford]

Lovely job. Why engineered and not solid wood? And love the vinyl @28:54

[@MK-yo4jn]

Yay new video. I’ve been watching some of the old ones waiting for new content to arrive 😂

[@GosforthHandyman]

Cheers! 👍

[@dawidczerniak5177]

Good video with nice bit of advice… I’ll be laying my floor next week and I’m sure I’ll use some of your tips and tricks… Nice floor by the way

[@johnboyginger]

Lovely job. Having had a mains water pipe pinhole leak under the kitchen floor, I shudder at the thought of that happening with these glued-up floors.

[@vincentshields9140]

Did you record laying in the flooring around the stairs with the curve? Interested in seeing how you completed it.

[@dougsinden6881]

You can always unscrew the cap and put cling film over bottles screw cap back on

[@torbar9603]

I did flooring a number of years back and recently I discovered there was some damage to a number of boards due to an office chair with incorrect wheels. This was not noticed as there was a mat under the chair. The company that made the floor is still in business but they do not make the same "model" (colour / grain pattern) also their new floors are a few millimetres thicker. The damage was in the middle of the floor and the whole apartment used the same flooring.. I wish I had a number of boxed left over when I did the floor (I planned well and only had one extra board :-( ) You should take two or three boxes and save then somewhere safe in case of future damage. --- I ended up staining the damaged boards with a similar colour and then varnishing them.. you can see the boards are different when standing above them but from else where in the room it is luckily fairly invisible.

[@GosforthHandyman]

Oh no! Yeah, wheeled chairs can be a killer on floors. Thinking bamboo for the studio.

[@SenselessUsername]

I had similar wood flooring and followed instructions to glue by tongues. In the fifth winter or so it has shrunk, so it broke into two large pieces with a 5mm seam between? In summer this gap shrinks to maybe 1mm, but each dry moment it's big. Is that preventable? I'm wondering if it's because some heavy objects at both ends stopping them from moving; or just too little glue?

[@andrewdraper8336]

Floor looks really good.

[@GosforthHandyman]

Cheers - really pleased with it!

[@JoeB_BSc]

Hi please advise the underlay make (with its silver side down) that you used as we are having a new floor put in our kitchen on this Thursday 8th September. About a metre is concrete, to the backdoor. I look forward to your reply, Thanks and Regards JB

[@Gunner071978]

Can I ask I didn't think you could lay a wood floor over floorboards as they will move and mess up the top floor.. and can I also ask why you chose to install as a floating floor and not glue the top floor down. I am about to do a herringbone style to my whole house but bill be replacing all the old floor boards with 22mm chip board and glueing the top floor down..

[@lfcloyal8284]

Yeah good job Andy lad....i laid some 9 inch oak floorboards about 10 years ago in a 19th century house..a lot of head scratching but looks the business..unfinished boards with Rustins dark oak dye 👍🏻

[@GosforthHandyman]

Nice! Had something similar a while back. Dark oak with Rubio monocoat.

[@lfcloyal8284]

@@GosforthHandyman 👍🏻

[@viankalobosvalenzuela7456]

Bellísimo trabajo felicidades 💯👏👊👌🏻💪

[@GosforthHandyman]

👍👍

[@willyoung8257]

We’ve got the same engineered flooring in our living room and it’s great stuff. Had it fitted by a professional (friend of a friend) though

[@GosforthHandyman]

Great stuff - lovely flooring!

[@ben4547]

Awesome job Andy. Novice question here. What's the best way to ensure a dead straight and parallel string line end to end if the walls you're running the boards along aren't straight? When hanging wallpaper with a plumb line you obviously have the weight that finds the dead straight line for you. Cheers

[@ironpirate8]

I'd say you need to pick a wall that the floor will be most noticable running along and measure off that to the other walls to see how parallel they are. If it's wildly out, you may be able to compromise a bit, or it may not matter if the flooring at the other wall is covered with furniture for example. Or instead of starting at a wall, you might want to choose a feature like Andy's hearth. Measure everything twice and make as many chalk lines or pencil lines on the floor as you need to, to show you how the floor will work out.

[@rzv500lc]

Knee pads in your pants ! Playing cricket or laying flooring ? Whatever love your vids . Inspired me to start my own handyman biz 6 months ago best decision I ever made ..... thank you

[@GosforthHandyman]

Fantastic stuff - best of luck with the business! 👍👍

[@ironpirate8]

Where are you from? Work trousers with kneepads and holster pockets seem to be a European thing. Edit - I realise you're probably having a laugh because Andy said pants. 😁

[@Greggspies]

Like your stair carpet

[@stomperthemixer1]

Amazing to watch but reminds my how hard it was on the joints when I last done this. Looks amazing Andy, well done to you both. I think I uses this or similar for my double conservatory when I get around to changing the flooring. Stay safe buddy.

[@GosforthHandyman]

Great stuff - cheers Neil!

[@njuham]

Nice job and Mrs Mac looking as lovely as ever.

[@GosforthHandyman]

Cheers! 👍👍

[@bernherts]

How fabulous is that 👍

[@peterdnreynolds777]

Brilliant work, feels like the light is appearing at the end of the tunnel. What's next? Kitchen installation? Still can't believe how wonky that hearth has been cut. Hope all is well, take care

[@GosforthHandyman]

Cheers! Yup, kitchen next! 😁👍

[@josephinebrown7827]

Absolutely beautiful 😍

[@GosforthHandyman]

Thank you! 👍

[@nickbell8634]

Lovely job that as always. We have similar but the boss wanted herringbone pattern! That took some working out. Was easy in the end but my god had me worried. 😂

[@gs425]

Can you explain how you did the cut at the bottom of the stairs please? did you cut up to the stair carpet, or did you cut the stair carpet to hang onto the wood?

[@GosforthHandyman]

Cut up to the carpet (quite tight but there's still plenty room for movement. Got the shape using one of these: www.amazon.co.uk/Jakarflex-Flexible-Curves-Drawing-Drafting/dp/B01DWEZ4DS

[@gs425]

@@GosforthHandyman thank you

[@celery4564]

Sometimes watching your videos I wish you was in the site management trade, would love someone as skilled and professional as yourself to oversee the renovations needed on my house.

[@Quaker521]

Nice job, looks great.

[@GosforthHandyman]

Cheers bud!

[@ArthLud]

Very nice!

[@halstirrup]

Am about to start laying my 20mm thick oak floor. Manufacturer tell me glue and screw to timber subfloor. What do you think of that advice. Cheers Mate