Genie Wireless Keypad ACSD1G Program/Erase-Intellicode

Download manual @ gsoverheadsyste... Detailed instructions on The Genie keypad model ACSD1G white flip up for Intellicode. Replaced the black slider model. How to clear the keypad of old codes before reprogramming a new code. If you had a problem programming, this could be the reason. Setting a temporary code and erasing the codes. Also how to erase all remotes and keypads programmed to the motor. The red light next to the smart button is working but hard to see in the lighting.

[@lesedwards9203]

Thank you! Was working on reprogramming my Genie keypad for about 4 hours with no success. Held down program and open/close buttons simultaneously, no luck. You said to hold down program, 6, and open/close buttons simultaneously. I did and had the keypad reprogrammed in one minute. This is a very helpful and clear video. Thank you so much!

[@pacobrown9683]

Bought a house with this keypad, but the PIN the previous owner gave me didn't work. This video did a great job of showing how to clear previous codes and reprogram a new PIN. Saved me some money, because I thought I was going to gave to buy a whole new key pad. Very clear, easy instructions.

[@cristinadigioia1521]

GREAT! Factory does not give clear idea of getting rid of old PIN's. Nowhere did they mention the "6" key!!! Thank YOU!!!

[@uptheorg]

I watched five videos and yours was the only one that worked! I spent about an hour doing what the other guys in the other videos did. The big difference I think was your instruction to clear the unit by holding down all three buttons together. Thank you!

[@87mtnrd]

So helpful! I wish this was in the Genie website. Thank you!

[@bluazur55]

Thanks it worked. I moved into a house with this keypad an an older Genie opener. Even Genie on the phone couldn't figure it out. Ha.

[@rafirc8yt]

THANK YOU :) the instructions on Genie website have not mentioned to first reset the keypad; followed your video (including the keypad reset as first step) and all worked; again thank you.

[@anthonylundquist2086]

Great job! The wireless keypad instructions once you have erased and reprogramed FAIL to mention now go to learning button on the Power Head to complete the programing. Thank you for putting the two together.

[@vjayejaye5503]

i can find my manual, this Video is spot on. I went to Genie's website and how they tell you to program and clear codes did not work for this model (ASD1G) They never mention the "6" key. Thanks for making this Video

[@tmsweat]

This video is actually informative and gets right to the accurate programing, unlike other videos. Thanks for the informative video clip!

[@GSOverheadSystemsNovato]

+Tim Sweat Glad it was helpful. Thanks for the comment.

[@tracijaeger9644]

Thank you so much for posting this video. I kept getting stuck on one part and was trying to get it to work for probably 30 minutes. You cleared it right up for me and I had it reprogrammed in 5 minutes after watching.

[@thinloki5902]

It was very easy and you were very clear about everything you were doing and I appreciate that because the other guy that has the same video was not as clear as you were my dude thank you

[@groodscom]

Great video! I found this old keypad in my garage from the previous owners but I was able to get it working (without knowing the original pin) with the help of this video.

[@Saosingfang]

had not been able to reprogrm the keypad after reading. It said pressed 1-2-3 prog to program. Your video solved my problem.

[@rictor]

Thank you for this video. This video helped me recode my garage door. I had some bad roommates move out and I needed to change the entry code. Thank you so much

[@mikrascally]

Best one to explain that I found!

[@EddieDalton]

first video that explains it properly, thanks sp much. worked perfectly

[@1960Cheeky]

Perfect ! Works now after sooo long trying other methods. Thanks.

[@fizzymouse8164]

Finally, instructions that worked. Great job on the video. Thank you

[@yukuhana]

Thank you! I didn't know I had to go through the LEARN sequence after changing the PIN.

[@ministangs]

Thanks for the video. I bought a used keypad to replace my old one and could not get it to program till I cleared the keypad first.

[@JE1212Y]

You just saved me from buying a new one...Thank you!!!

[@stevenlange2742]

Agreed, thanks for making this. I didn't know that the head unit stores codes as well, I must have held that down too long and cleared my keypad sync. The only thing I would ask is that you cover how to set this up for two openers. My original configuration was the code + up/down + (door # 1 or 2) then up/down again. I tried to add a 1 in the sequence, but couldn't get it to work? Thx!

[@nickeyriley7113]

very well under stood, & right to the point Thanks

[@scotttaggart]

Very important and I make this mistake every time: You must hold the buttons down for a "long" time (e.g., about a second or so each). If you push them quickly, the remote will not respond as shown. Notice how long he holds each key.

[@Rushan2112]

YES-you are so right. I spent wayyy too long on this, and was doing everything correctly, with no luck. The long solid button push was the key.

[@lauram1875]

This should be a pinned top comment! I have been working on this and nothing worked. When I held them down like you suggested, it worked! It made sense when I read this because when using the keypad normally I always need to hold each key down for a second when entering pin. THANK YOU!!!! 😀

[@aprilb29]

Excellent video. Easy to follow instructions. Worked perfectly. Thanks so much!

[@ChadwickVonGriffindorIII]

The learn light on my unit doesn't go solid.

[@iamtuckermac]

Great job, very easy to understand and follow your instructions.. thank you ..

[@mist4926]

2nd time you do what push program or put code and push program????

[@KhanhNguyen-xl3ul]

Good job 👏

[@HungNguyen-mz1ti]

Very useful instruction. Many thanks.

[@TheMdterp]

I just did this and the explanation was perfect. Right to the point and simple to follow. Thanks a bunch!!!

[@mikewilson6472]

Great video. Did not work with mine ‘cause it is broke I guess.

[@jimbo5728]

This was a huge help! 👍👍👍

[@eddie9903]

Thanks I will try it just the way you did it. hope it works.

[@cobhome]

Thank you for t he video, however, this model keypad will not program the same as you instructed. I gather it's because I have the "Accelerator" door opener..don't know. Just add four (4) hits of the open/double arrow at the end and then it works!

[@GSOverheadSystemsNovato]

Yes, I believe that is a newer model. Thanks you for mentioning that.

[@adrianmn4376]

I following you instructions but now I not available o use the opener from my vehicle

[@mist4926]

ok so got it to work but now the first garage door wont work. tried fixing that but now both dont work

[@bobschlott8527]

Thank you! Got the job done.

[@wallaroo1295]

THANKS FELLAS!

[@stanleyb279]

MY DOOR KEYPAD WAS WORKING UNTIL MY IT GOT WET FROM A POWERWASHER. I CHANGED THE BATTERY BUT THE LIGHT ON THE UNIT DOSN,T LIGHT UP OR WORK. THE DOOR STILL GOES UP AND DOWN FROM A ANOTHER OUTLET BUTTON INSIDE THE GARAGE AND ALSO WORKS FROM MY CAR.

[@vsojeanslevantacola2512]

Thank you very much

[@godsvideo]

Very helpful! Thank you.

[@joecoffee986]

Could Genie have made their keypad more complicated to program?

[@metaface4113]

Thank you for t he video. 100% fonctionnel Merci

[@ssgdean1969]

The written instructions suck. Your video was outstanding!

[@faradpack]

how far from the unit should I be when I do the learn button, my unit is stuck on the wall firm not sure if I can slide it up, can I just do it from 9 feet or so away?

[@faradpack]

Yes, thank you, all I needed was fresh batteries

[@josephmuigai8632]

Great. It works.

[@Corlocka]

Thanks buddy it worked

[@teddybogdaniec2608]

Awesome video!

[@user-ko4tj7co6g]

Why is my gene not engage ing

[@cristobalpenaoconitrillo8968]

que este en español

[@anamikachauhan9832]

THANK YOUUUUUUUUUUUUUUUUUUUUUUÙUUUUUUUUUUUUUUUUUUUUUU