Dave shows how he does a pocket port on a Honda K series. Learn what tools and techniques to get it right on your own!
Пікірлер: 52
@rayray75213 ай бұрын
I am definitely using this shop . Under standing for the why gives value to the work . Thank you great content.
@headgames3 ай бұрын
Awesome! Thank you!
@zc18crx3 ай бұрын
The did my k20 head, best decision I've made
@tedphimsiprasom40423 ай бұрын
Finally a K series video, more of it please!!!!!
@headgames3 ай бұрын
we can do that!
@LatinoAD17 күн бұрын
I'll be shipping you my k20 cylinder head early next yr for you to do the pocket port in it Dave. Love you papi .
@SRDmotorsports3 ай бұрын
This is why whenever I have a US based or CA based inquiry I always always suggest and direct them to HeadGames… they can never go wrong with the choice of going to HeadGames😎 awesome work and video Dave and good selection words 😎
@headgames3 ай бұрын
Thanks for your kind words
@SRDmotorsports3 ай бұрын
@@headgames but uncle Johnny needs a raise 😂
@headgames3 ай бұрын
@@SRDmotorsports he’s been hiding behind the scenes lol
@SRDmotorsports3 ай бұрын
And there you go 10k goodness!!!!
@barnes4g63Ай бұрын
I would love to see a k20/24 vs the 4b11t flow comparison. And your thoughts on both. Keep up the awesome videos! ❤
@headgamesАй бұрын
That is happening!
@goyocarreras3 ай бұрын
Thanks Dave, excellent work and technical explanation. Regards Goyo
@headgames3 ай бұрын
Welcome!
@arturozarate17523 ай бұрын
Must be nice utilizing the long shank burs! I've used the big Makita grinder for 20 plus years and bent soooooooo many long shanks, and I've cut them down to 4" or 5". I'm definitely considering new equipment. Just thinking back to how many manifolds I could've done so much more work to with full length long shank burs 🤦♂️
@headgames3 ай бұрын
Yeah I hate that big Makita. I made an L out of one of our burrs as soon as I turned it on. I threw it under the bench and never went back. You would love the smaller Makita. If you do a lot of manifold porting you might get some kick back in tight areas, and there is many area's where your not supporting the burr, I would suggest to buy 2. You will break the plastic bearing inside the grinder. Other than that, it really is a game changer and so easy to hold all day. And you can spin it full blast with a 3/4 burr 6" long with no problem.
@christophercruz79323 ай бұрын
Great videos! I like the Honda head videos. I have two B16 heads.
@headgames3 ай бұрын
Very nice! We will do more Honda!
@syukrimusa18503 ай бұрын
awesome video full of knowledge
@headgames3 ай бұрын
Thanks!
@highpsiguy40853 ай бұрын
Good morning Uncle Dave
@headgames3 ай бұрын
Good morning beautiful
@weduhpeople85043 ай бұрын
Head games can you explain the pros and cons of hand porting compared to a cnc port job or a combination? What and why would I choose one experienced porting company over another? Also if you can do a video of which head components are better than another. Supertech, Ferrea, Brian Crower.
@headgames3 ай бұрын
CNC vs hand porting we can certainly do that. Which brand is better, without pissing off vendors we work with is kind of impossible. BUT, we have shown things to look for. They all have their place.
@alexcrummell89092 ай бұрын
Love the explanation. What are the cfm improvements at low mid or topend. Cheers
@burnz31323 ай бұрын
Wanna see a 420a Mistu or SRT-4/ PTGT head ported. Was told with +2mm I/E valves you can open it up quite a bit. But I don’t trust that! It ultimately takes your word before I believe it lol.
@headgames3 ай бұрын
Sadly you won't see that on here. We haven't done a 420A head in many years. And certainly wouldn't be using that big of a valve if we did. But do appreciate you commenting and kind words!
@burnz31323 ай бұрын
@@headgames maybe I should send a few lol. I know not really much of anyone else wanting to seem them
@BraapSupport3 ай бұрын
and first again!
@headgames3 ай бұрын
@Christopher-re2hl3 ай бұрын
Has anyone done any out of the ordinary experimenting. I have this idea about making air straightening grooves at the beginning of the port all the way to the throat by grinding with a small dremel. Chrysler had air straightener vents on their hood scoops. Try it on a junk head and flow test it
@arturozarate17523 ай бұрын
If your grooves ran parallel to the length of the runner and were shaped to be "fins" you may see increased port velocities. Properly placed of course. One fin at the center of the floor before the short turn for example. That's proven to be beneficial on a single intake valve.
@headgames3 ай бұрын
@@arturozarate1752 agreed. I think he is talking about making trenches. Is that correct @chrisopher? If so, I don't think that is beneficial.
@arturozarate17523 ай бұрын
@@headgames trench warfare?🤣🤣🤣
@mrphiscal3 ай бұрын
Ej heads difference between the casting. 🤷♂️. Dual AVCS
@headgames3 ай бұрын
Only problem is I don't know what head comes in what car. Like I know the heads, but I am sure people would want what that head comes in. I would need a buddy lol
@AmirPomen3 ай бұрын
can u show us porting tips for subaru EJ heads please?
@@headgames thank you very much for the "heads-up" ! 👍👍👍 Lovely... 😘 Cheers ☕☕
@rolandotillit28673 ай бұрын
Honda heads are already oversized as it is. The ports don't need to be bigger at all.
@headgames3 ай бұрын
You don’t need to make them bigger per say but you can make them better. Shape matters.
@rolandotillit28673 ай бұрын
@@headgames Exactly! This guy knows.
@ICTPerformance2683 ай бұрын
🇦🇬 ⭐️⭐️⭐️⭐️⭐️. 🙇🏾♂️
@BraapSupport3 ай бұрын
80 Subscriber left!
@headgames3 ай бұрын
Less than a week at this pace!
@LUCKYDRAGSTA3 ай бұрын
Get it digitized and cnc port it. why you still hand porting you can never match a machine.
@headgames3 ай бұрын
We might digitize a pocket port at some point, but we still have to blend every head that comes out of the machine. The machine can spit them out but it is still a casting so you are dealing with core shift and they are not all the same. A hand knows where the port is, a machine only knows where it should be.
@arturozarate17523 ай бұрын
Yeah the cnc process might save a little time and the cut would be the same cut it was programed to make, but the shadowing will be blended by hand and I've had better flowing short sides after hand blending. Why you love the machine so much?