HF 20 oz gravity feed sandblast gun review and modification

best sand blast gun after a small modification.

[@johnasumaa8644]

I have the same tool. On page 8 of the instruction manual, under General Operating Instructions, it says "WARNING. Do not use sand for blasting." Further down, it states that compressor pressure should not exceed 90 psi. I had no problems, after reading the manual. That's what it's for.

[@5thGenNativeTexan]

Not sure which manual you're looking at, but that's not what it says. The warning is specifically regarding using sand with silica, and it's NOT that the unit can't use sand, the warning is specifically about breathing silicosis and aluminum oxide.

[@jefbretschneider1607]

Impressive! I love you didn't quit and your modification worked!! For people seeking an inexpensive sand blaster, this video shows how the mod is done. Once again, Friends, Live and learn! Thanks, Anatollii!

[@gcong2]

Outstanding modification! I REALLY appreciate you going through he steps AND bit sizes. Good job!! Going to buy one tomorrow.

[@StiNbJu]

Thanks for this mod video and sizing on bits/holes. I know this is 2 1/2 years old, but for folks that are coming here later, it does indeed say not to use sand. However, I found a decent work around to get consistent media size from Home Depot sandbox sand. I first put the sand out on a tarp to dry in the sun - Then use a mesh strainer you can get from Walmart/Target and filter into a milk jug/soda bottle through a funnel. It takes out the largest pebbles and gives a generally consistent media without clogging.

[@TotoGuy-Original]

you should use crushed glass instead of sand because sand is bad for your health some countries have band the use of it

[@coldspring624]

@@TotoGuy-Original stay off the sand beaches on a windy day right

[@rolfbjorn9937]

@@coldspring624 You don't blast the beach sand at high velocity on metal plates while breathing the dust though. The NO SAND warning is because of silicosis, a lung disease that's nasty and occurs quite fast when exposed to significant amounts of silica (sand, concrete, plaster and other dusts, even glass) either over time or in acute exposure.

[@colm7837]

Dude, you just saved me so much sanding. Tryed the gun yesterday, didnt work. Been procrastinating sanding the molding on 10 oak doors for my friend, your a life savour man !

[@thomaslcrawford]

Awesome video. Thanks for taking the risk on the modification of your new tool and for sharing with us!

[@rob12449]

Holy Cow! Some hobbies should not be tried without researching the danger or hazards! When I saw you hold the metal with a bare hand and I was already concerned when you stated going to home depot for a bag of sand... If you accidentally pass that over your bare hand it can take off flesh. Sand is risky, even with a dust filter, when you take it off the dangerous dust is lingering in the air. Yes some sands are safer than others but why mess around, get some blast media.

[@TheNYgolfer]

Man you are a true blue Harbor Freight customer. Harbor freight sandblaster. Harbor freight cordless drill and those dangerous gold drill bitts that snap in a heartbeat . I drilled a piece once like you did. Held the piece to be drilled in one hand while drilling with the other. The bit snapped and I drilled right through my thumb with the broken bit that was left in the drill. What a bloody mess . I NEVER buy drill bits from Harbor Freight anymore.

[@ronburns6865]

Nice details, I have an old one that I never use because it never worked well. Going to work on that. Very handy to not have to pull out the big blaster for small jobs.

[@mikepeel1121]

I just bought the same unit, and out of the box it failed to work, thank you for showing how to modify, good job

[@richardberger414]

It does work out of the box if you use the proper media. Home Depot sand is made for a child's sandbox. It does not have a consistent grit size. I've used glass bead & aluminum oxide with great success. Moisture will clump the media and clog the gun, you need a water separator right at the gun.

[@hunterwingler543]

What grit sand do you need to use ?

[@richardberger414]

@@hunterwingler543 I got decent results with 100/170 glass bead

[@poolbob8776]

Good job dude. You got that thing working great !!!!

[@frankviramontes139]

Awesome job on the modifications thanks ,thats exacly what I need it for ...

[@vicjames2743]

Found me a new tool to have for my shop. The mods worked great. Thanks for sharing

[@tolikgord]

Great to hear!

[@ELSKEETO]

Soda didn’t didn’t do anything to the powder coating I was trying to remove. Thank you so much for the help. Sand (dry sand) worked like a charm.

[@brianbutterworth8186]

What kind of sand can you use once you make this modification?

[@ELSKEETO]

@@brianbutterworth8186 Play sand from Home Depot.

[@brocktillman1014]

Thank you for the review friend! Very helpful on my end!

[@vladorlovsky6623]

Great review. Thank you very much!

[@gottabighit1]

Justt bought one yesterday. I'm gonna make the modification before I even use it . Thank you, sir.

[@23steph13]

How did it go?

[@gottabighit1]

@@23steph13 I’d like to say it went well, and I did get it done. Works incredibly well. Just took about 8 times the length of this video. LOL But worth the effort.

[@bmodllc]

You saved my weekend project(my problem) thanks for the share

[@wer6shaffers]

Thanks bro. Just what I need for my bicycle projects

[@jessemitchell8012]

I just brought one of those guns and same thing out the box it did not work so thank you very much for making this video it helps alot cause I was about to take it back to the store

[@scottryan9845]

Excellent video I'm going to buy the gun today , thanks for the info

[@wadedblade]

You have a 50/50 chance with this sand blaster, I did the modifications and it works great now but the guy next door to me, his worked right out of the box. I am also glad you remind everyone to wear goggles and gloves are a good idea as well, Thank you.

[@PeterFeltersnatch852]

What media do you use

[@nateb4543]

I've heard a lot that a respirator or mask is very important. Guessing it makes paint dust or something.

[@Hereford1642]

@@nateb4543 Not just the paint dust. The very sand itself that is being used for blasting here contains silica and you can end up with silicosis which is no joke.

[@nateb4543]

@@Hereford1642 ya since this comment i strained sand i had for blasting, there was a bunch of dust and looked it up. Now i wear a reapirator

[@Hereford1642]

@@nateb4543 My work here is done.

[@RedlandsBuzz]

thanks Anatoli. Mine worked out of the box but not as good as i wanted. Im gonna mod it like you showed.

[@wildmanjac1]

Just picked up one of these today along with a used 5.5 hp compressor for $70.00. Hooked everything up and loaded the gun with glass heads. I’m going to etch glass. Cut a stencil on my Cricut, stuck it on a glass I wanted to test on and it was fantastic. I live in SW Florida so humidity is a way of life here. Installed a desiccant moisture absorber in line and went to town. I am throughly empresses with thing. It does a great job.

[@steelvet3133]

Thanks man! Great share! God bless you brother!

[@machineman6498]

👍 will do this before using the one I bought. Thank you for making this.

[@danamcintyre3565]

I found that making sure sand is dry without moisture and i also siffted the sand makes it work great !

[@stevedawson256]

Wow , I have the same gun with the same problem, I'll be doing what you have done , first thing in the morning, thanks

[@waynedaudelin6119]

Nice job looks like it works much better

[@erictownsend8711]

Thank you very much for the demo on the mod. very helpfull

[@gilnicolas6377]

how many psi you use

[@BamaDanKnives]

Going to give this a try!!

[@punisher6001]

Thanks man, this is the same problem I am having with mine.

[@steadyeddie7453]

The most important factor in any media blasting is having the proper media. Home Depot sand is not made for sandblasting. It has tiny rocks, pebbles, and debris in the bag. You need either sand made for sandblasting, or you can filter your own sand through a screen to remove the larger particles that are clogging the valve and the tip on the gun.

[@ProleDaddy]

You're just talking about the fancy sandbox sand that you can get at HD.

[@wayawolf1967]

The "O" ring took you right back to a small opening.

[@NWPencrawler]

Nice job. Just bought one and will make the mod.

[@clifficus]

Nice mods, impressive, thanks for sharing 👍😃

[@PlayerLeonardo]

I bought same model as you and have the same issue...gonna try those modifications, thanks

[@rolfbjorn9937]

NO SAND warning is because of silicosis, a lung disease that's nasty and occurs quite fast when exposed to significant amounts of silica (sand, concrete, plaster and other dusts, even glass) either over time or in acute exposure.

[@AXNJXN1]

Brilliant mod.... Gonna tear mine apart now.

[@floppybeefcurtains7679]

This is awesome! Great work! Also putting that little black car clip in that top hole is fucking genius lmfao. Thank you!

[@macpakinga1271]

Awesome modification thank you for sharing. 🤗🎸🌏FNZealand

[@andredetailinggardengarage280]

Thanks for this video... I have this Air Gun too... Ans this problem too.... Now i know what i must making. Thanks

[@mac2k2020]

oh it does work you just need to get proper blasting media sand from home depot is not good most likely too much moisture , works great with soda

[@BenRivered]

Great video!

[@martybrooks5593]

excellent - nice job! thanks

[@tolikgord]

Thanks

[@bshend]

NOT supposed to be using sand through this gun. Says right on it not to use sand. Glass beads worked great through mine. No issues. Haven’t tried baking soda but should work too. All this extra work was unnecessary

[@hmroa3056]

How much blasting media do you use with these modifications in place?

[@vandresv]

I followed this recommendations and the blasting improved a lot, but still was not good for the task at hand. I was trying to remove old paint from a porch light and it failed miserably. My compressor does not hold 90 psi for more than a second or two, it drops to 60 very quickly, so that might be my problem and not the improved modified gun. Thank you.

[@SteveMirabelli]

When blasting with sand use at least a dust mask as silica dust is very hazardous to inhale.

[@LatinDanceVideos]

"silica dust is very hazardous to inhale." silica dust is really bad, it lingers in their air and doesn't settle, then becomes airborn. most states have banned it's use. it's worth the spend to go to a tool shop and buy the proper sandblasting media, plus get advice on the right material to use for your job.

[@Ezekiel-OffRoad]

@@LatinDanceVideos Blasting media is quite expensive especially if you don’t have a way to recover and recycle it I don’t agree with banning the use of silica sand just saying it’s dangerous or hazardous isn’t the best warning either they should put the definition of silicosis then people could make an educated decision to use a respirator or not

[@ronhancock4607]

@@Ezekiel-OffRoad Yup... lungs are more expendable. This video is dangerous, the sand is illegal in the US.

[@josesepulveda9425]

Exelente amigo ,saludos desde chile

[@marshallguerra1353]

Thanks for the information.

[@MultiBegbeg]

excellent pistolet !!

[@afroomega77]

Good job!

[@allraiders420]

This guys spraying an inch away from his fingers.. fucking legend.

[@BillLowenburg]

Obviously not an experienced user. You’d think, however, that someone could kinda figure out that if the tool is meant to remove paint and rust, it MIGHT be wise to: a)wear some good gloves and b) keep your hands and other body parts away from the nozzle. C) wear a mask or better yet a respirator and goggles or a face shield.

[@mariebourn8317]

dumb question. when he drills out the gun he said all the way to? or through? the bottom? not through and through right?

[@pianobar7801]

very helpful, thanks

[@joewalker1654]

I had the same problem. Unfortunately, I didn’t see this video until I returned mine to the store.

[@grahambate3384]

gr8 video cheers

[@anthonys5170]

Definately working now

[@bennyhill1200]

How many horsepower and scfm are you running from the compressor?? Thanks David

[@randyhigginbotham961]

Nice mod. I might revisit mine ($0) vs buying a new sandblaster. I just have a small job to do

[@jwandhistools]

I gotta strip the paint off some old steel wheels for a repaint. Liquid strippers barely phase it. A 2400psi pressure washer with the needle tip does not phase it. Think this would do anything?

[@amramhakohen7474]

Spasibo! Dosvdanya хорошо! спасибо!

[@joh331]

Well done brother. Thanks for sharing your advice with us !

[@elpulpas]

what size of sand did you grab at home depot

[@chaz353535]

Great video

[@danbrownellfuzzy3010]

I found sacks of black grit at Menards. I think it was eleven bucks or so. It works great but you are constantly refilling the hopper. I tried baking soda today. I dont think it's as aggressive but it lasted a lot longer. I bought sand and it didnt go through, im sure glad it didnt, the comments said I would have Silicosis right now. I have a respirator so i might get a second gun to modify.

[@frankdavidson9675]

you can use river sand if you dry it out first i use a metal bucket on a propane burner to dry the sand quick and easy damp sand will clog any sand blaster

[@4npushap352]

Definitely tried to run to thick of a media and a water/air filter would help as well but still good video man

[@aldalbertomarchena9625]

good job, sir

[@tolikgord]

Thanks

[@ichhier5165]

Thank you. I almost dumped the damn thing.

[@nateb4543]

Did you use actual sand? Or abrasive made for a sandblaster

[@rottiejakeluke]

Fi like the mod, but wonder if it would stil work if blasting with SODA? Or is it only used, no, with sand like media? Thank you.

[@betocastaneda1597]

I think it works much better than the other bigger ones, right?

[@msi4226]

whats the compressor psi you are using buddy?

[@2000jago]

What sand are you putting in there?

[@mattblack9344]

How big was your compressor. Maybe that was the problem, plus moiture. But well done. A+

[@jeremywatts2768]

Can you use soda with it?

[@kennethgray3794]

Nice Bro!

[@millin2222]

Do you think this device would work on raptor paint with sand??

[@chevecrazy454ss]

This is perfect for those wanting to blast coarse media yes it's probably not intended for it but it obviously works so i dont see the issue for all the ppl wining

[@wandaredparker6802]

Have the same gun don't work thanks will try this thumbs up.thanks again 👍😀👌😊🙂

[@coloredcaboosecreations]

Ok I’m intrigued and totally gonna try it. What size air compressor are you using please? Thanks for sharing!

[@tolikgord]

The bigger the better. They recomended 90psi pressure and with small air compressor you will be waiting more then blasting.

[@davidzornes6863]

Great !

[@rubenmorales9891]

What’s the power of your air compressor thanks.

[@sgakla]

It works fine out of the box if ........get this....... you follow the instructions!

[@cellinitv2756]

Like a day at the beach

[@marquezvanroeschen5340]

Nice mod! :) Any chance to share your compressor specs? FAD / Actually Delivered l/min

[@igotakai5644]

What type of metal did you blast in the video?

[@keithnegron2287]

ah crap! just bought. didn't work either. time for mod. thanks! I was using walnut shell, probably much bigger than soda or glass bead.

[@patrickperry6945]

I’ve had one of those for a long time. Has never performed properly, like yours. I’m gonna make those mods. Get a hood. Keep the media out of your face and hair. Also filter your media with a 5gallon bucket and window screen. You can figure out how. I used the bucket lid to hold the screen with about an 8 inch hole in it to hold the screen. I use play sand and filter (screen) it. Or you can get blasting sand from some hardware stores.

[@ronnyfountain7566]

Do you actually use it on camera other wise

[@ainzooalgown6450]

Thanks for the link to product 😅 good review but how can I find this particular blaster?

[@keronackles8327]

Do it only work on aluminum

[@alexandrpavlov4474]

Анатолий, здравствуйте. Спасибо за видео, собираюсь обзавестись таким же или подобным. Как вообще впечатления от аппарата после доработки? Можете рекомендовать ?)

[@jacktar5867]

Yeah mine is doing the same, Just thought it was a piece of scheisser, Didnt think about doing that mod, Guess i will be taking it to work tomorrow to modify when i get a spare 5 minutes

[@carlosfrances01]

What size is the connector you use ?

[@jrorellana4865]

Thanks for the video, I did the modification on mine but it still didn't work properly. Can you please tell me what size air compressor you used? I have a Dewalt 16 gallon compressor, I used play sand and also tried black diamond media. Could the compressor size be the issue? Thanks

[@ichhier5165]

The capacity of the compressor only influences the possible duration of sandblasting. The grain size of the medium may be too coarse.

[@faustinomartinez707]

Exelente yo compré una pero salío defectuosa de la entrada de aire estaba quebrada. Saludos