How a Worn CV Axle Can Cause Vibration

This video is mainly an informational video. In this video I have a great example of a CV axle with a worn inner joint that caused a vibration upon acceleration. I take the inner joint apart and show what happened to the inner joint and explain how a worn inner CV axle joint can cause a vibration upon acceleration.
Note: While it is very common for a worn inner CV axle joint to cause a vibration upon acceleration you need to keep in mind that this is not the only thing that can cause this symptom. You will need to properly diagnose your vehicle before performing a repair. Below is a link to a video that will give you SOME information to help you in diagnosing a vibration upon acceleration. (while this video has great information, it may not have ALL the information you need to properly diagnose your vehicle.)
Here is the link to that video: • Vibration Under Accele...
Also, the explanation of how an electric motor can slow a vehicle down was just a superficial explanation. Of coarse it was not the purpose of the video to go into depth about that. Also at about the 1:00 mark I mention that the electric motor slows the vehicle but I did it in a way that may seem like I said the motor uses the brake rotors to slow the vehicle down. What I was trying to say is that the motor, not the brakes, slow the vehicle.
DISCLAIMER
Barbour's Auto Help is not responsible for any damage or personal injury incurred in the process of performing any auto repairs done by you the viewer. Automotive repair is extremely dangerous. Repair your vehicle at your own risk. It is the viewers responsibility to verify all information and procedures as outlined in YOUR REPAIR MANUAL AND OWNERS MANUAL FOR YOUR VEHICLE. Owning and using a repair manual suited for your vehicle is essential for correctly and safely performing ANY repair to your vehicle. Always wear safety glasses and heed all instructions for use applicable to any piece of equipment you may use. Due to circumstances out of the control of Barbours Auto Help, Barbours Auto Help makes no guarantee that by the use of the information given in this video a quality repair will be made. Barbour'sAutoHelp makes no guarantee that the information provided is totally complete, syncronized and accurate. Verify everything using an appropriate repair manual. Follow the repair manual over this videos content. You can do it. Do it right and do it safely.

[@MarzNet256]

In addition to slight vibration on acceleration, there is vibration when breaking hard at highway speeds. It's not the rotors. The cv axle (passenger side) would also make a rumbling sound when banking left above 55mph. It made a little noise on slow sharp turns-no clicking just a rumble. The boots have failed, making a mess. Getting it replaced today. I've learned my lessons about putting off repairs...it's no picnic. Great Video.

[@Daninater]

It's so much more valuable information when you know HOW something can cause vibration. Thank you for taking the time to explain.

[@BarboursAutoHelp]

No problem

[@BarboursAutoHelp]

Probably not here. It may be best to have it looked at.

[@robertalicea5585]

@AusAhmet check motor mounts

[@dannytrinh07]

@VatanTURK It's motor mount, the upper one. And if drive or reverse engaged and it jerked, the lower mounts as well. Definitely not the axle.

[@alexgardner543]

Thanks for that explanation. i recently bought a second hand car and had a vibration develop while going down hill with a feathered throttle at 75-80kmph. Eventually, on longer 25-30km trips the vibration would develop at any speed. This was just after a clunk occurred and I was lucky to find a bolt from the RH inner CV sitting between the suspension arm and a chassis member. LUCKY! Looking into replacing the Axles this month!

[@BarboursAutoHelp]

Good luck.

[@TX2673XA]

My steering wheel, floor and right seat vibrate between 70 and 90 mph. I changed new tires and new rims and the problem persists.I have balanced them about 8 times, the last time they came out 0 with 0, that is perfect and it still does.😢Hard to find good mechanics. Have a great day, thanks for the video.👍

[@jamesxc2004]

This was exactly what i was looking for almost a week now. Just needed to confirm y would inner cv axle vibrate and cause noise while driving. Gives me confidence to just replace the tripod bearing rather then all inner cv. Cheper 50 compared to 400. Saved me half a days work inspecting myself and $350 on replacement. Thanks.❤

[@billburgess9100]

Good math, good thinking.

[@HeySeussGranny]

Good video 👍🏻 I'm distracted by that mockingbird. He is going smooth TF off 😄

[@jimstelljes3925]

Good video of an example of the issue with the inner CV joint.

[@mrs.kristophermartinez4927]

Thank you so much for your channel. I hope this is my problem because I'm having the exact symptoms. Your videos on this have been a blessing to my life. I wish I was your neighbor or your niece Lol. I need you in my life right now Lol

[@6lastresort]

This has been the most helpful video for me yet. This is the first time I’ve heard someone say that you can have vibration after de-acceleration.

[@frank-bmtz]

Me too! Don't have a hybrid vehicle but my 08 Fusion vibrates at de-acceleration and when accelerating from a complete stop. The description he gave at the beginning is exactly what my car does now!

[@phillippardo5712]

@@frank-bmtz did you ever figure out the issue? Mines doing the the same. Along with a clacking noise upon acceleration and deceleration

[@CullenCraft]

It can happen on manual transmission cars while engine braking

[@bryang2724]

Your video is describing my issues exactly. I'm gonna have to check my cv axles. Only thing is I've put the vehicle in neutral and it still slowed down like the brakes were being applied as well as a harder brake pedal feel but only when the issue arises.

[@ianchiwo3536]

Seized brake calipers

[@padukamegatdewa1962]

thank you, that was an informative video. keep it up. I have a NAZA RIA @ Kia Carnival in MALAYSIA, the same problem happened. so now at least I know what to do instead of spending money for unnecessary parts replacement. Sometimes when we go to the work shop, the repair man will tell many other problems that we have to pay for many parts replacement instead 1 actual problem, it just for their business income purposes. That is nonsense. Anyway your video is helping. TQ again.

[@cyntil4362]

Thank you for creating these videos...I don't know much about cars, (but wish I did!).. when my PT Cruiser started vibrating upon acceleration recently..I took it for service right away. Despite my description of what was concerning me, the garage seemed to only plug the car into the diagnostic machine. They claimed it needed new plugs and wires...$700+.. OK...I guess?...I do know that bad plugs, and cracked wires can affect a car's smooth running. Those parts were original to the car(2006-I checked thru my bills to make sure).. They called me at the end of the day, to say it ran better...but it still juddered. ..they also swapped out the rotors, to see if those were warped...(they were not) After a few days...the car was finally fixed. It was the RF axle/CV joint. Fearing an astronomical bill...to my surprise, they admitted their "misdiagnosing".. and changed the axle and rotors no charge. This PT has been a great car, relatively few problems over the years. I figure to keep it going as long as I can. As a senior, I'm in no position to take on a new car, or car payments, nor do I really want to. I just wish mechanical stuff was taught in schools to women way back when. We weren't allowed to take any shop type courses when I was a youngster. I will be checking out more of your videos in future..as the PT ages, it's going to need more fixing I'm sure...so thank you for sharing all this info!

[@Williedamaris]

I have that problem with 2003 camry. Thanks for the video.

[@photondebuger45]

Makes an annoying popping too when you hit the gas too and stop as well. And good showing how it's supposed to work too, it's supposed to be telescopic at the inside joint for the suspension and it extending on the jounce and rebound at the wheels.

[@nicolastremblay7527]

I've been searching what was my issue on my car. The brake aren't warped, no play in the wheel and good alignment. I just found out my issue with your video ! Thanks a lot !

[@II-er7gj]

Thank you BARBOUR'S AUTO HELP for this valuable info! Now i know why my VW POLO 2005 are vibrating like a crazy when accelerating from 30 to 60 mph. Thank you so much! You saved my money! Thank you so much!!! Now I exactly know what do I need to repair in garage.

[@BarboursAutoHelp]

Well, have you actually had it diagnosed? Just because your symptoms are similar doesn't necessarily mean this is your problem.

[@SuperReallyNice]

👍tried to tell my dad that was his problem, kept saying trans is going out. Thank you!

[@Slowcarfastbeans]

Oddly enough, after several months of vibration when braking at 65mph+, I got this idea it might be the inner CV joint causing it on my CT200h. I’ve experienced the inner CV joint vibration on acceleration and didn’t think it could be the inner CV joint unless it also happened during acceleration. Will know for sure once I replace it with a known good.

[@BarboursAutoHelp]

I hope it works out for ya!

[@pureblood_ALPHAMALE]

Fantastic video and explanation! 👍 Helped a lot.

[@BarboursAutoHelp]

Thanks

[@ananefrimpong7070]

Good video. Thanks for the vital information.

[@hssello]

Thank you very much I didn't know inner CV can Course vibration your demonstration was so good 👌👌👍

[@BarboursAutoHelp]

Glad it was helpful!

[@wilhelmmaravilla8898]

Very interesting, Thanks for sharing

[@marlonsalvador4327]

This is really helpful, i have the same problem. The clunking noise is annoying. Thank you

[@BarboursAutoHelp]

Thanks

[@damienfought1949]

Thank you this is very I formative I have a 2007 Hyundai azera and both of my cv joints are bad so I ordered 2

[@cenos8521]

Excellent video . Thanks for making it .

[@BarboursAutoHelp]

Glad you liked it!

[@tylerstrong1878]

Dude this video saved me! I thought my transmission was going out on my mew 2013 rav 4 and it was the cv causing it around 40 to 45 mph then started popping when I would back up or start off even turnin sometimes it would pop once or twice.

[@BarboursAutoHelp]

Man, I'm so glad to hear that!

[@phillippardo5712]

@@BarboursAutoHelp I'm curious if maybe one of you guys can help, my 2010 jeep compass is making a clacking noise upon acceleration and deceleration. It sometimes even does it when shifting from park to drive or park to nuetral. Please note that is does not make the noise when revved in park or nuetral, but does when put into drive and foot on brake and revved just a little. Anything is much appreciated thanks guys!

[@firecrew1049]

@@phillippardo5712 idk if you figured it out but it sounds like u joints

[@basshnter1606]

Great video and exactly what is wrong with my 03 cr-v.

[@BarboursAutoHelp]

Glad to help.

[@summerbee60]

awesome vid and really helped me understand what's going on. Thanks!

[@BarboursAutoHelp]

Glad it helped!

[@robrohrke8694]

Good video. This helped me with the vibration on a buddy’s truck.

[@Bertrum123]

This is the best vid I've watched 👍

[@MrAquinas1]

I have experienced vibration with braking when I had a bad axle and was sure I needed a new rotor, but I knew I needed a new axle more urgently. So I changed the axle first figuring I would get to the rotor another time. But the braking vibration was eliminated also after changing the axle!

[@BarboursAutoHelp]

Cool!

[@trevordavey5196]

Good video, nicely explained and proves older cars ned checking. T

[@citylumberjack8381]

I have a 2012 Audi Q5 that I bought about 4 months ago. From the day I drove it off the lot there was a problem with a very subtle vibration not visually noticeable but definitely felt through the entire car steering wheels/seats dashboard at all speeds from 30 km/h and upwards with no limit. The faster you drive the more noticeable it is. I have had this car in and out of about 15 shops/mechanics and I'm at the end of my rope and my patience. Ive had the wheels balanced/Road Forced/alignment multiple times along with other shops trying to diagnose unsuccessfully. I've been told everything from CV Joint to Struts and coils/mounts to control arms/tie rods and wheel bearings or tires feathering/cupping. Some shops have even said U joints or propeller shaft or torque converter. Everyone wants throw parts at the car and not one mechanic do I trust. The vibrations are making me so angry when I drive and I would rather do the repair myself but not sure if your video applies to non hybrid Quattro style german cars. It's more noticeable upon acceleration, but also there during coasting or braking just not as much. I'm desperate for answers

[@BarboursAutoHelp]

The info in the video is common to most vehicles that use CV style axles, to a degree. Have considered taking it to an Audi dealership to have it properly diagnosed?

[@citylumberjack8381]

I did take it to Audi, actually 2 different Audi's. One said front brakes and rotors so I had them replaced. $900. The other said it needs a road force balancing with proper adapter - donut shaped not spherical - and proper wheel alignment. $600. Its like burning money. I hate dealerships, I don't trust them and this car is well out of warranty. Audi wants another $700 just to diagnose and disassemble parts to inspect with no guarantee of finding or fixing problem. At what point do I put my foot down and say enough? If they actually change the CV joint/s it will mostly likely be in the range of $1500 - $3000. Its not even inflation its absurdity. A regular mechanic will still charge at least $1200.00 as per quote with OE parts if that was even the problem.

[@BarboursAutoHelp]

Sometimes that’s the road you have to go down. Sorry your going through this. It’s a tough pill to take. What ever you end up doing I hope it goes well with you. Good luck.

[@Jstro14]

I'm gonna get under my own car in the morning as I just got home and it's freezing (northern USA Maine) because since yesterday I've noticed a pretty good vibration going on in the front end. Being I've had the same issue before but it was snow that did it last year it was frozen inside the back of the rim ( aluminum rims) these on my 06 G6 are steel and I see no snow from just looking we'll see in the am what I find. The vibration starts around 40 or so and worse at 60 so I kept it at 50mph on the way home from work. Definitely giving a thumbs up on the video. If you comment back I'll respond. I know I need ball joints, sway links excitedexc exc only had it on the road for about a 10k miles which I knew it needed those parts just wanted to make sure the trans or anything else is broken. This spring I plan to fix it but if it needs a cv I'll have to get that done in the next couple days.

[@BarboursAutoHelp]

Good luck to you. Keep us posted.

[@jeremynelson1333]

Thanks for such a good explanation brother! Subbed.

[@BarboursAutoHelp]

Thanks for the sub!

[@codesterbamb7744]

i've had the same issue for a while on my subaru tribeca 2012. Changed the rotors thinking it was that, but nope. Gonna order my drivers side cv axle and do a self install.

[@hamag1973]

Maby this is my problem. Thanx for a really good vid. I will check the drivechafts and also the kardan on mine👍

[@osasgideon8431]

Thks for the educative video. my question is , apart from the vibration does a bad cv axle make a grinding noise ?

[@BarboursAutoHelp]

I've not heard a grinding noise cause by a half shaft yet.

[@habh8r77]

Thank you for ur detailed explanation

[@MuhammadKhan-yl7mt]

Very good info. Great work.

[@BarboursAutoHelp]

Glad it was helpful!

[@michaelmendez-castillo9453]

Great info thank you for the knowledge.

[@slimskinny]

Can a bad cv axle cause you to feel a vibration in the gas pedal when going over bumps? I also have the vibration on acceleration as well, but I only feel it in the gas pedal. I've replaced all my engine mounts, and tire rods.

[@BarboursAutoHelp]

I suppose it's possible. A lot of things could cause that by the way.

[@TortureBot]

My wife's 2011 Rogue feels like the transmission slips two or three times in quick succession when you are coasting and then apply the accelerator to start climbing a slight incline. It does it between two and four times or so and feels like something is slipping and trying to lock-in to pull. I assumed her CVT transmission was going bad since they are known for that, but for some reason this particular year model has been excluded from all the complaints from the years before and after with cvts. I admit she hasn't changed the fluid, but when it was being serviced at the dealership I asked them to do it and since the fluid was kind of dark they recommended I didn't do it or it might make the problem worse. It has about 135,000 miles on it. They said there were no codes stored pertaining to the transmission when I was having them try to diagnose it. The problem really hasn't gotten much worse since we first noticed it about 7 months ago. I know we have a torn CV boot for the passenger side CV axle and it needs to be replaced. if it has begun to wear while the boot has been torn, is there any chance it could cause a symptom like I described?

[@BarboursAutoHelp]

Without experiencing it my self it's hard to say. From the sound of it that CV axle would just about have to be falling apart to make it do that. Id suggest having a tech diagnose it. You may be pleasantly surprised at what they say.

[@GermanShepherdDaphne]

Yes! I’m having same issue and it’s being fixed now. Part messed up axle into front differential

[@GermanShepherdDaphne]

My axle is screwed. Someone changed wheel baring and didn’t put it back on correctly

[@TortureBot]

@@GermanShepherdDaphne So you say your Rogue is doing the same thing ours is doing? Acts like it's skipping or the transmission is slipping?

[@jomel1638]

On the left side of my car I getting a vibration on the axels from 40 mph to 60mph so is that ?

[@suecook8379]

Hi thanks for the video. Anything else that would cause a shimmy when accelerating?

[@BarboursAutoHelp]

Yes, I have a link to a video down in the description that goes over this a bit. Check it out.

[@suecook8379]

Thank you

[@RetroPCUser]

I had vibrations when hitting the brakes, but not the acceleration and my car had bad tie rod ends and poor alignment. My left front side is making a scrapping noise when turning left, stopping, or accelerating (might be the pads on the front end, wheel hub assembly, or brake shield scrapping against the rotor).

[@BarboursAutoHelp]

Thanks for sharing your experience.

[@taher1973]

Excellent video. Thanks

[@alexlopez525]

Hey man I’ve been have a similar issue going on, Everything has been running fine until a couple weeks ago and I was hoping you could point me in the right direction for what my pick up is needing. Recently my pickup started to make this humming/moaning/grinding sound almost like if there is rubbing going on. Which is ONLY when i go into reverse. It’s seems to come from the front end right below me, In drive she is perfect and It's for sure not tire rub. They were thinking it was the rubber on the cv boots getting rubbed. But there is no sign of distress or leaks.

[@EWH87]

I have a 2002 Volvo S60 and notice the steering wheel wobbles at a low speed. Sometimes all I have to do is let off the break and the steering wheel will jolted to the left. I notice durning an oil change, grease around the boot and I’m thinking that’s the issue. I’m hoping it’s an easy fix to do.

[@forgottenknowledge8917]

I'm replacing the drivers side CV axel today. The part was 200 bucks and I'll install it myself. The job is worth 400-450 in Australian shops. I'll do it myself.

[@Dani-it5sy]

I have a Hyundai i40 that has got this replaced 2 times now with only 40k miles on the clock. I just put on a brand new driveshaft again and the wobbling is almost gone but I can still feel it slightly under load sometimes. Seems like there is something else wrong with this car that makes the driveshaft wear way to fast. I talked to the previous owner and he said he had complained about this while the car was under warranty but Hyundai just said it was nothing. Probably the wheels or bad road surface. But now we see it was not ''nothing'' . It's something serious. A drive shaft should last MUCH longer than 20k miles. Wheels and alignment are spot on. Got several very experienced mechanics to check everything and they don't really know what it can be. Motor mounts are ok to. Starting to get quite desperate now 😣

[@Mrdubomb]

I just don't understand how some axles can appear fine on the bench but actually be the problem, case in point 2015 RDX, severe shimmy felt in the steering wheel and bad enough to shake your fillings out, took a chance and sourced two cheap Chinese axles without any balancing rubbers on the shaft and visibly had more slop in the tripods than the oem and it fixed the problem. Nothing surprises me anymore. If these cheap knock offs last a year Ill be impressed.

[@carlosnaranjo4701]

Excellent thank you for your help

[@chickenfarm09]

Could it also feel like warped rotors when coming to a slow stop? I have an intermittent feeling of what I thought was warped rotors but I would think rotors would happen at every stop.

[@licket72]

I have the same problem 2013 AWD Toyota sienna vibration when exlelerating. she shop change the right rear axle and it's doing the same thing so said it could be the iner bearing that the axcle goes into the diffencial .the put the van on the lift and exelarate and said the lift axcle was a bit wabbling so the change in but it didn't get any better.what do you suggest

[@0xDEAD-C0DE]

My Honda civic has been vibrating when pressing the brakes. Mechanic said it was the rotors. I replaced them and the vibration went away, but came back again. Now while going down the hill my car steering wheel vibrates quite a lot. Yesterday I checked the inner passenger CV axle and it has an up and down play. I suspect this will be the issue with the vibration while pressing the brakes.

[@jessecastro8898]

Great info. Thank you. Anyway I do have a " clicking noise but only after new CV axles were replaced..help!

[@BarboursAutoHelp]

Who installed them?

[@moreetlhomphochiba2189]

I should have found you earlier, should I ge a new tri pod only ?

[@jackjohnson4629]

I have a 2007 camryLe when I putt into drive or reverse it has rough idle, in neutral it runs smooth. I have checked all possible parts related to engine vibration, Could this be axsle related due to problems only apply in gear? thks 4 taking my question

[@thomasbradley5419]

Possible that it could squeek when you hit bumps as well? I have. 2009 honda civic ex coupe

[@sa1nt_john.v1]

Yeah I think mine is the inner joint. There's a very slight click I hear from time to time. But my problem is vibration when accelerating to about 30-40 mph and much more at 60-70 mph.

[@YxnginJesusLovesU]

Same bro

[@juliomarenco4411]

What was it ? I’m having the same issue

[@sa1nt_john.v1]

@@juliomarenco4411 before you do the cv axels check your tie rods. It still shook after I replaced the axels, motot mounts, rotors, brakes and ball joints. After all that it was my $40 tie rods that were bad and caused the shaking.

[@juliomarenco4411]

@@sa1nt_john.v1 will do thanks, would it vibrate a lot ? From 0-40 it’s normal but after the fast I go the more it vibrates and goes away when I go back to around 30mph

[@juliomarenco4411]

@@sa1nt_john.v1 I just don’t want to be changing parts that don’t need to be changed 😂 already balanced the tires and it wasn’t it

[@SWells679]

Good explanation. Thx. I just had this exact issue on my 06 Odyssey. It felt like vibration was coming from right, front. Changed both CV axles and it turned out to be the driver's side.

[@BarboursAutoHelp]

Good job!

[@kevinmetcalf6371]

Great video bro. Tks

[@aquilinosanchez636]

Excellent explanation.

[@BarboursAutoHelp]

Thanks

[@MichaelHatfieldFlowers]

Thanks man, got this issue on my Sentra, the steering wheel also shakes when I brake, and I I believe it’s getting worse as the cv axel seems to get worse, I changed the brakes rotors and made sure the guide pins on the caliper were cleaned and greased, what do you think? I know you said the vibration is upon acceleration typically in non hybrid cars but it really seems like the steering wheel shake gas been caused by the cv axel going bad, they seem to worsen together, but who knows sometimes with cars, I’m going to change the cv axels anyhow, I’ll let you know if it goes away.

[@BarboursAutoHelp]

Hey, sorry I didn't get to you until now. I've got a decent video on diagnosing vibrations upon acceleration. It may or may not help you but I believe its got some good info for you. Here is a link: kzbin.info/www/bejne/haq7pXWnet2em8U

[@mwlplaytime769]

I think im having the same issue with my sentra!

[@ashleyduff2393]

So did you figure this out? My 07 Camry is having vibrations when deceleration..any data points would be appreciated

[@watchmegetoutoftheshelter7690]

Thanks for the info man, I just got my 2007 Lexus GS 350 AWD go through two Axle at my local Meineke Care Center wondering if it's my transmission going need your opinion?

[@BarboursAutoHelp]

What was wrong with the axles?

[@watchmegetoutoftheshelter7690]

@@BarboursAutoHelp I was driving on the highway with my family for adults and a baby I went over a bridge quick dip and the axle broke in half at the time I assumed it was a flat tire but visually the axle was in two pieces passenger side.

[@watchmegetoutoftheshelter7690]

I went to my Meineke repair center and they said to me that the axle needs to be replaced and so they did on arrival to pick up the car I asked him if there's anything else wrong with the vehicle and they said I'm good to go I took it for a test drive out of the parking lot and the axle fell out again I brought it back to them and they replace that axle with another and the same thing happened I'm trying to figure out if it's the transmission that's spitting the axle out

[@BarboursAutoHelp]

I've seen this happen a long time ago but not on a Lexus. The vehicle had a bad engine or transmission mount. It was causing the axle to stretch too much. I'd give the mounts a good check. Not saying that's it but it could be. Let me know what you find.

[@ismaelmarte1981]

@@watchmegetoutoftheshelter7690 how much you paid for the repair

[@RobertFWWhitlock]

Can a worn cv joint cause damage to wheel bearings, transaxle, suspension parts etc?

[@suntzuwarsword1964]

Thank you..very helpful

[@BarboursAutoHelp]

Glad it was helpful!

[@lonnie4679]

Good video thanks

[@jonnda]

I'm getting it on both acceleration and deceleration, but only on highway conditions. 1997 Acura CL 3.0 I knew the CV axel was bad due to the clicking when turning, but I thought the vibration was due to the tires. Put on the new tires (old ones were old and dangerous as well), vibration is still there. Axle is next I suppose.

[@Cliffjumper]

I have an Acura CL 97 too. After replacing tie rods, ball joints, wheel bearing, and tires w/ alignment. I was getting a vibration that would pull the steering wheel to the right...Then disappear. I suspect my front passenger axle is bad, as well.

[@jonnda]

Cliffjumper Turns out it was a bad caliper. It was locked up and it would cause one brake rotor to warp when overheated and vibrate. It needed tires, axels, and brake system work, but most of all it was the brakes.

[@tommason5689]

The boot seems to be ok. So what would cause the grease to dry up like that?

[@billburgess9100]

I replaced the drivers side cv axle today on my 2008 Toyota yaris. The boot had a big rip and all the grease was gone. this was at the wheel side boot. Naturally the bearing was very worn.It never made the much talked about "clicking" sound when making hard left or right turns in a parking lot. Oddly it only made a thump, thump sound like a tire that had bump in the tread. Hope this helps somebody.

[@davidmakowka922]

Hi, I have hamming/vibrating noise coming from passenger side, when I'm sitting in driver seat. It's like something is spinning in uneven way. Zero up to 100 km/h nothing. It starts at 100 km/h, peaks at 110 km/h and disappears at 130 km/h. That sound is definitely connected only to car speed and not to engine rpms. Its louder when pressing gas pedal/accelerating, but it does not disappear completely when not accelerating. Its not engine, because that sound is same when in neutral or any other gear. Its not unbalances tire or wheel. I tried many different wheels. Ball joints are perfectly firm. Sound does not change when braking. There is no play in wheel in any direction. I've already changed both sides bearings and inner transmission side axl homokinetic joint since I found this joint could cause this sound. No rubber boots were damaged. All looking good as new. I used high quality replacement and nothing helped. Axl itself looks perfectly fine. I also tried clicking test when turning full left, full right and accelerating. Nothing, there is no clicking sound. No I dont know, this sound started just like that 4 month ago and does not get better or worse. Still the same. I didnt hit pot hole or anything. I'm driving quality highways. My car is vw golf 6 with only 110 000 km in very good shape. Now I plan to change outer wheel side homokinetic joint, but I dont believe it will fix it. I will be glad for all ideas and suggestions.

[@warrenpeterson5709]

Gosh this sounds like what Im going through. Endless fixes and replacements and problem still persists. CV Axel is my next guess but these guesses are getting expensive. What was your final resolution?

[@shiftautomotive854]

I had my cv axle replaced by a shop and then my car started vibrating when picking up speed from a stop. I went back to the shop to complain about the issue they said they will fix it. And still the vibration has not gone. All of this started happening after I got my CV axle replaced

[@strahinjapantelic2869]

hello mate, i have play in spot where drive shaft enters into gearbox, so after this big rusty part which is on left side in the video (i dont know how its called)...so when i take this big rusty part, and moving it up down, left right, i have play in spot where this rod enters gearbox...is that ok, and can be reasone because i have vibrations due to slow start from first gear or reverse???? thanks

[@erikharris6682]

What causes frontend vibration at highway speeds only while coasting or very light throttle with out touching the breaks. There is a clunking also felt in steering wheel when light rockinh it right and left while sitting still . 2019 volkswagen atlas all wheel drive . 3.6 l. ( engine is in sideways ) outer tierods appear tight aswell as balljoints ..

[@jamiesimko]

Thank you!

[@ycvsat]

I had the same vibrational problem with my Jeep Grand Cherokee. Vibration upon acceleration. I changed the CV axle but it wasn't that. My mecanic fixed the problem in changing the transmission supports that was disaggregated.

[@wilsonemeka1833]

What do you mean by transmission supports? What are those?

[@ycvsat]

@@wilsonemeka1833 It's written 'Isolator' on my invoice but my mecanic called it 'transmission support'. The right term is probably 'transmission Mount Isolator'.

[@leslieedwards6650]

Should you replace both if only one is bad?

[@user-pc5ic1ti5u]

i had my passenger CV axle replaced due to a leak in the boot. Then a few thousand miles later i started getting this vibration you talked about. I assumed there was some issue with the part, so my mechanic replaced the axle again. I thought this fixed the issue because the vibration went away. But then after a few thousand miles it started vibrating again. i don't know what to do next? It seems a new axle fixed the issue, but maybe the axle is wearing out very quickly? Any suggestions on what to do next? The vibration only occurs during acceleration between 45-60mph.

[@ingonyama-giveitatry4966]

I have a problem with my polo VW. so when I drive more than 80kmph and when I release my foot from the acceleration pedal my steering shakes heavy and feels like it wants to throw me off-road to the left side. I have to take gear to neutral for it to slow down and then speed a bit after that when I take a turn a hear a hard knock then it drives a bit fine. but high speed it gives me that. rods, ball J, and stuff are fairly new.

[@shanewilliams7645]

Will a cv axle also slip when you come from a dead stop with no check engine light on the transmission

[@icebreaka1969]

1 to 2 mm is a lot in a vehicle part clearance specs, most of the parts are calculated in super tight little spaces like intake valve clearance, only around .18mm to .23mm in my car, which means there is .05mm difference allowed.

[@BarboursAutoHelp]

Ok, so how does that relate to the video? I'm sure you have a good point, I'm just slow at connecting the dots. What are saying?

[@dillonwood2864]

So I got a 2006 Buick rendezvous cxl and when do sharp turn got popping sound and now when driving while turn wheel it sounds like a wobble on passenger side and got vibration while idle and comes from the driver wheel so is it bc of this part going bad?

[@jasonmccorkle8760]

I had a grinding that sounded a lot like a wheel bearing problem but upon closer inspection it turns out the grinding noise is coming from the upper cv axle joint. I haven't found any information on this yet. A constant grinding coming from the upper cv axle that is. If you have the time and any information on this it would be greatly appreciated. I understand if you cant reply. Thank you a ton for your videos they have helped me tremendously.

[@geraouttahermaeens1075]

I had the same noise I replaced all 4 wheel bearing a in the end still noise similar to wheel bearing. Did you fix your noise if so what was it.

[@jasonmccorkle8760]

@@geraouttahermaeens1075turned out to be the transmission

[@tommason5689]

@@jasonmccorkle8760 Was it AT differential shaft bearings? I changed both front wheel bearings but I still hear wheel bearing noise, sort of whirring noise, not constant grinding, and with slight vibration, mostly at speeds above 40mph. It seems to come from passenger side. I am not sure if it is from inner CV joint, CV axle carrier bearing, or AT differential. Boots on axle are in good shape. So it makes me hesitate to replace the whole axle.

[@EarmuffHugger]

@@jasonmccorkle8760 Did you fix the problem because I think mine is the transmission too but I'm taking the hub bearing & cv axle off now. Loud growling hum at 20 mph + apparently coming from the driver side.

[@geraouttahermaeens1075]

Is the noise similar to wheel bearing noise and slight vibration

[@tshavhungwehellems]

Well explained 😊

[@BarboursAutoHelp]

Thank you 🙂

[@frankmcneal1925]

i have a 2018 camry se.. when im driving at high speeds and start guiding left my can starts vibrating. what could it be? its starting to get worst!

[@hodgepodge919]

My 09 Subaru has been making clunking/squeaking sounds when driving at lower speeds, and when accelerating while going straight or after turning there is a vibration/sound for about 2 seconds every time. Could this be my cv axle or boot? Do struts need to be replaced if the axle is damaged?

[@nabaddame5726]

If the inner joint is bad is it possible for there to be a vibration at all speeds? Like a constant type of vibration? Also how can you diagnose the play being the inner joint vs the transmission bearings?

[@BarboursAutoHelp]

It could cause vibration at all speeds. But typically its at a certain speed range under acceleration. Here is a link to another video that may help. It doesn't cover "everything " but it will help you along a bit.. kzbin.info/www/bejne/haq7pXWnet2em8U

[@dowork3709]

ive had a problem with a lil clunk when I'm. going down my drive way.... i also noticed the vibration when going bout 50 or so i let off.. then gas it again and its good... what im asking is this... would the cv axel mabey making a clunking noise too...( its the same sound as when u shifted the axel in the video)

[@BarboursAutoHelp]

Its possible but I wouldn't guess at this. It's probably best to have a tech look at it to make sure if you aren't mechanically savy.

[@mychannel-mt3ik]

Did you ever find out what was making the noise

[@LuisPerez-bk3cm]

do u know what cv axle brand are good ? Thanks. I have a 97 toyota camry le v6

[@TheBobinn]

OEM or rebuilt OEMs, dont buy cheap crap you will end up replacing them 3x as often..

[@VaiComDeus89]

This seems like the issue I'm having with my 2012 audi a6 prestige. Got my wheels balanced twice in one weeks and still getting this vibration and shuddering when accelerating at 57 - 65 MPH. Is this a bad CV joint? I also hear some noise that appears to be coming from the axle when turning left...Is that the CV Joint?

[@BarboursAutoHelp]

Possibly. If you aren't confident have a tech diagnose it for you.

[@victordaki7569]

Thank u so much, my cv boot is worn and my car volvo S60 2004 vibrates on acceleration worst on steep. I drive it less than 100km per month. Do I need to change the boot and Grice or the whole cv joint? M from south africa

[@BarboursAutoHelp]

Not sure what you need. But if the axle is bad greasing it and putting a boot on it won't fix it.

[@na93prepre]

Interesting. I have a vibration on my 1995 corolla while accelerating. It only happens around 45-50mph and then goes away above 55. I wonder if this is my issue.

[@ScreamoCat]

That's wheel balance

[@kazparzyxzpenualt8111]

Clicking at low speeds. A humming drone at faster speeds. I was worried it might be one of the cv's but couldn't tell left, right, inner, or outer.... until I put the car up and went around and tried the individual joints. The clicking while turning at low speeds became more and more noticable so it was really starting to worry me. The inner right side cv has turned out to be the culprit. Have not noticed vibration on acceleration yet. Really wondering when the problem will become a regretful roadside event. $$$$

[@budleyfranks9393]

Is this the cause for the axle to come out of the inner joint?

[@gametime2425]

I have a 2010 Ford Focus SE with about 128,000 miles on it. I’ve been replacing some older parts based on tire wear patterns and now have new issues. I replaced the rear drums, rear shocks, put new tires on the back from cupping. Front tires are 11 months old. I replaced the front strut and spring assembly, new brake pads and rotors, I also put 8 new wheel studs on the front and got it aligned. The right CV axle was replaced 9/8/18. I still have front end vibration from 0-20mph. It is amplified when turning right and accelerating as well. Does the driver’s side CV need replacing? What else could it be? TL; DR Vibration from 0-20. Can’t locate the problem. Thank you!!

[@BarboursAutoHelp]

I have a link to another video that may help you out in the description of this video. That being said, paying to have an experienced technician diagnose your vehicle may not be a bad idea. It could even save you money by not paying for parts not needed.

[@AguilaJR]

Great video! Is it possible that free play in inner shaft only be felt with axle out of the car? My car has the vibration during acelaration symptom but axles feel very solid and boots are intact. Thank you in advance!

[@AndresLopizesuno]

Might need some balancing on wheel or tie rods or ball joints

[@fasanyadamilola484]

I just changed the CV axle but I still get this vibration at 50km/hr. Also, I feel the vibration more in the middle of the car. Also, note that I have removed the propeller. What could possibly be the cause of the vibration

[@Potato-mu7nu]

Thank you!😊