great video.....these valves are usually the problem when pressure will only go to about 500psi....2 things to add....the top valve in the cylinder head is free to rotate with vibration...so fails to shut off, that was my problem.....so on reassembly instead of silicon oil i used a spot of loctite to stop rotation.....also the second valve you show us should be seated in the top off the cylinder where there are recesses for it, i have not found this one to rotate so just popped it in and rotated to correct alignment
@willemdeysel17662 ай бұрын
Thanks very much this was helpful
@davegallagher44983 жыл бұрын
Thanks very much this was helpful the instructions that came with it were not clear at all.. that's really helped
@derivas0076 жыл бұрын
great video it will be good to see more for example how to lub the second stage ring,how to change you gasket,...and how to change motor if it break for you what is the best compressor? i have tuxing txo1 and i am happy but some parts are cheap like temperature sensors, feet sucction base.
@avenshang85436 жыл бұрын
will update more videos in the furture. and i think the orange digital compressor is better, fill faster and quality more stable
@rodrigoilabaca94193 жыл бұрын
Aven Shang, very good video, thank you very much for sharing it, I have the same compressor (Blue) and I must perform maintenance since it does not have the strength to fill 280 bar. Could you explain to me what function the piece that you show in the video has, in writing, since if you did it speaking in the video, I do not understand the language in a spoken way, only in writing, I only know Spanish. Thank you so much
@theocarvalho8105 Жыл бұрын
Boa noite, essa peça de alta pressão, onde eu compro??? As 2 onde eu compro???
@avenshang8543 Жыл бұрын
Hi, you can find it in our store: www.aliexpress.com/store/5584107
@theocarvalho8105 Жыл бұрын
Mandei mensagem lá no Aliexpress com a foto da peça
@eumellopez24376 жыл бұрын
thanks aven,,
@Acids20027 ай бұрын
Sis hole? Sis valve? Place Sis ?😂😂😂
@radman7313 жыл бұрын
Hope all is well. It seems I can’t find much help troubleshooting my Yong heng. It had served me well for 2 years , but unfortunately it had failed me today. I have no idea where to start or what to replace. Both air chambers are holding pressure, but it just won’t go past 1500psi ( I usually fill my 100cu 4500 guppy tank , all the way to 4500. Never had a problem until today ) I do notice of a crank close the release valve (with a bit of force from a wrench) on the second chamber it will climb to 2000psi but if I hang tighten it will fall back to 1500psi and just float there running. I don’t know what to do. I can’t fill my tank anymore. Any help would be appreciated. I’m prepared to take apart, but I have no idea what to replace or look for , like I said.
@avenshang85433 жыл бұрын
hi, pressure can't exceed more than 1500 psi? did you clear the valve on both side of compressor head? or open the head to clear?
@sultan267064 жыл бұрын
hi i have like this put i have problem i see water cooling coming to cylinder where you think this leak ? i open may cylinder i found rust inside
@Juntzo096 жыл бұрын
Is it the same for the Digital Control Set Pressure Auto Shut-off air pump? If not, please also do a video for that version. (The yellow colored version.) That is what I have. Thanks.
@avenshang85436 жыл бұрын
Hi friend, different construction the digital compressor has, no these small parts inside, so more easy to fix and maintenance