www.billydavid... Check out our website above for the best online training available
Пікірлер: 41
@billydavidsonvip3 жыл бұрын
www.billydavidsonvip.com/ Check out our website for the best online pressure wash training available
@chocolatepie12302 жыл бұрын
Just finished power-washing thanks you sir. Your experience and knowledge clear pathway by adjusting the ball and spring WD-40 in it work like a charm
@rickwashek4783 жыл бұрын
Good video, I haven't used the alcohol or vinegar but I always spray the WD40 in the injector after every day of use.
@NoName-be5ir Жыл бұрын
Rookie mistake I made that was an issue my injector wouldn’t pull. I replaced my 50ft 5/8 hose with a 100ft 1/4 hose. I’ve learned that reduced my flow just enough not to pull chemical. Went back to the 5/8 and bam, starting pulling. 🤦♂️
@JunkNGrind3 ай бұрын
I have a new Simpson 4200 PSI and today water started filling up the chemicals that were supposed to be drawing out ? Does that mean the chemical injector got stuck? Obviously sir ?
@avren7988Ай бұрын
I’m having the same problem, did you figure it out?
@JunkNGrindАй бұрын
@@avren7988 The Spring and Ball is Probably Sticking inside the injector We started removing the hose from the Chemical Jug when not in use. I started spraying lots of WD40 inside the injector after every use. Some people say that they soak it in water overnight.
@pitztoplawncare67813 жыл бұрын
You earned yourself a subscriber
@billydavidsonvip3 жыл бұрын
Thanks I appreciate it
@alorlando8615 Жыл бұрын
Thanks Bill been watching your videos for some time now appreciate all these videos you make for us
@billydavidsonvip Жыл бұрын
Thank you!
@lowbudgcryptowashing49333 жыл бұрын
Billy man awesome video! But we really need to get you payed from Wd40!! You use that stuff for everything!
@momoney10413 жыл бұрын
Best thing for after using bleach
@davehumphrey40752 жыл бұрын
Thank you for the help. Dave from St. Louis
@billydavidsonvip2 жыл бұрын
Thank you!
@mikeklein4952 Жыл бұрын
on my pressure washer with a CAT pump, water is shooting straight up from the chemical injector, shoots up about 10ft in the air! I have no idea what the problem is?
@billydavidsonvip Жыл бұрын
Most likely you'll need to replace the chemical injector you make and try to take it apart and lubricate it with a WD-40 product. Just be careful there is a small, check ball and spring assembly inside of the chemical injector. This is common when the check ball gets stuck in the open position and allows pressure to backfeed through the small port. I have seen this probably 100 times at least.
@billydavidsonvip Жыл бұрын
If you look in the description of this video, you'll find my training website my personal phone number is on that website you can always text or call me for help
@garyanderson42742 жыл бұрын
What about when the injectors backwash Chemical back into the 5 gallon bucket?
@billydavidsonvip2 жыл бұрын
There is a small check ball inside the injector with a spring mechanism. Usually when it starts to backwash into your bucket there's either trash caught inside of the ejector or either the spring has broken. Often times we just replace it
@DoctorRickSanchez10 ай бұрын
@@billydavidsonvip_Billy you're the man! I got frustrated on a job and I went to the bare bones minimum & had to batch mix my chem with a foam cannon (basically like a cheap man's XJet) to finish a house wash luckily it was a small 2 story. Thanks a lot I've been looking for a straight to the point video on the injector._
@dannycrain34853 жыл бұрын
Great tip thanks Billy
@bradk4303 Жыл бұрын
Question. Pressure washer worked fine and now it will not pull chemical through the tube unless I turn the spigot almost off. It's a fixed injector on a Simpson MSH 3125. Any input from anyone would be appreciated.
@mandrew20111 Жыл бұрын
I have the same problem. If my hose is on but the pressure washer is off, it will pull, the second I fire up the washer it won’t. But if I fire it up with the trigger on, it will pull soap until I let off the trigger and it builds back pressure.
@johnsjourney777 Жыл бұрын
I have a Simpson also. I had the black tip in and it was pulling my cleaning solution well, I changed tip to white and noticed it was still pulling cleaner, I thought I only pulled cleaner with black tip.
@YouCouldNever.10 ай бұрын
@johnsjourney777 it pulls when there is a drop in pressure. Black tip is a bigger orifice so it triggers the downstream for detergent
@wildwestwashservices76123 жыл бұрын
Great video as always!
@billydavidsonvip3 жыл бұрын
Thank you. How have you been doing
@kismetcorp9 ай бұрын
Very helpful
@randytyson7552 жыл бұрын
Straight no chaser….Like!
@giantslayer4732 жыл бұрын
Billy, I did my 1st house wash this past Sat. Was really bluffed out ( worried about over doing the SH, even though I was downstreaming. Worried it wouldn't come clean ) but it went really good, saw the green disappear off the vinyl siding as I was spraying it- wonderful feeling. When I switched tips from black to white (to rinse) I looked over at my bucket containing the SH, and water was backflowing into the bucket of SH, running over the edge and onto the customers grass- UGH! Is that normal and something we need to do (remove the downstreaming hose from the bucket) or if not, what did I do wrong? Thank you sir.
@billydavidsonvip2 жыл бұрын
Usually those injectors will backfeed into your bucket with Eric going bad. There is a small check ball in the injector that gets stuck and allows it to backfeed into your bucket. I would suggest replacing the injector
@drewhaddox21973 жыл бұрын
Hey Billy, could you please do a video over Insurance and getting Bonded for us new guys?
@billydavidsonvip3 жыл бұрын
Hey I did one a couple months ago I'll see if I can find it and send you the link
@drewhaddox21973 жыл бұрын
@@billydavidsonvip thank you sir!
@go2powerwashatl Жыл бұрын
That would be great I'll do a search for it under your name. New to the biz that's one other thing I'm researching and the issue with the injector.
@St.Bowtie2 жыл бұрын
ever had water shoot from the injector ?
@billydavidsonvip2 жыл бұрын
Yes you can try spraying some WD-40 into the injector it's most likely the check ball stuck most of the time we just replace the injector