How to install 80cc kit Gy6(139QMB) Scooter engine Part 2

[@seanmayo206]

Gotta love those hollow bolts on the tensioner. Engineering marvel

[@SanyaTsvay]

9:17 Uszczelnienie olejowe nie jest głęboko zasadzone? ))))

[@g_garage]

Ta było, musialem troszkę wypchać...🤫🤣

[@rassez1253]

8:41 what is the block bolt torque?

[@g_garage]

www.rollingwrenchdenver.com/blogs/news/gy6-torque-settings

[@dantickle5562]

How did you remove the engine?

[@vicfigueroa3364]

I just have 1 question why did you put oil seals all the way down arentthey suppose to go flush with the crankcase

[@g_garage]

You're right,my mistake. I had to correct it.

[@MJ40FR]

Pas mal mais tu aurais du montrer comment régler le jeu des poussoir de soupapes ( 0,10mm) ainsi que comment calmer la distribution

[@christen8480]

Genuine question - when putting in the new 80cc, do you put on the old cylinder head or get a new one?

[@g_garage]

You can put old one, but better put new 80cc too

[@hans-matteusbristol9884]

Where did you get the 80cc engene kit? And what is it called?

[@hwlberd]

gy6 47mm big bore kit

[@jeffmee763]

You forgot the o rings for the oil pump at 6.39 that fit under the pump.

[@g_garage]

yes I forgot but I put them later, I didn't show in the video my bad sory

[@ThePahan007]

19:10 mising Oil Seal (o-ring) ??

[@g_garage]

I forgot at first and didn't show it later in the video my mistake

[@rallyscoot]

What valve clearance did you used for this 80cc kit?

[@sahinsucukk]

i would do 0.10 and 0.10

[@kumayblog898]

Hello, may I know the crank model you used? how many gear crank 22T or 16T which one ?

[@g_garage]

I don't remember sory

[@kumayblog898]

@@g_garage I installed a 47mm cylinder head and 50mm piston on my 139QMB 50cc engine. do i need to change the crank?

[@g_garage]

@@kumayblog898 you don't need to change the crank. But you lose some power if the cylinder is 49mm and head is 47. It will run, but not as good as on 49mm head

[@kumayblog898]

@@g_garage Thank you so much. good luck with your work

[@محمدعلي-ذ4غ7د]

you forgot the o-rings and the pin of the oil pump, also the spinnaker side drive bad installation

[@dapv144]

Can you show the motor mounting and wiring assembly?

[@g_garage]

Sorry I can't. I repaired it and returned it to my uncle. maybe one day I will fix another scooter and then I will record another video 😁

[@viosog9661]

Ce marca de cauciuc ai

[@mazmaking7342]

No joint in oil pump ?

[@g_garage]

I forgot at the beginning and didn't show on the vid my bad

[@rassez1253]

What is the size of bolt (6:25)?

[@g_garage]

I don't remember, you have to search sory

[@elveneye]

What oil do you use on them bearings and pistod head

[@g_garage]

Normal oil for 4t scooters

[@elveneye]

@@g_garage whats the brand name you used in this video? The orange can you use

[@g_garage]

I filled the orange can with Castrol Power 1 Racing 4T 10W40. The orange can is made in China brand 🤣

[@elveneye]

@@g_garage do you think I can use my engine oil Maxima Scooter 4t Petroleum 10w40 for lubricating other parts of the engine like the piston head?

[@g_garage]

yes of course😁

[@project6287]

hello how muche torq u use fore the bolts? thx greets from the netherlands

[@g_garage]

There are different torque values. Look in the service manual for the number of Nm you are looking for. Greetings from Poland😁

[@project6287]

@@g_garage do you have a torque mannual ? Ik cant find IT

[@g_garage]

www.google.com/url?sa=t&source=web&rct=j&url=www.49ccscoot.com/manuals/139QMB_Engine_Manual.pdf&ved=2ahUKEwj0gJCN-LftAhUKzqQKHW_NAMsQFjAAegQIBBAC&usg=AOvVaw0Iu2FYDy0t9gwYzd6k5gGA

[@project6287]

and that v-beld is Broken see 16:59 @@g_garage

[@miroch19]

Witam co zrobić jeśli zawór jest krutszy o 4mm można dać śrubę od karty od spodu?

[@g_garage]

Nie rozumiem, mógłbyś lepiej opisać problem albo wysłać mi jakieś zdjęcia na Instagramie ?

[@miroch19]

Da się na messengera wysłać jub imel

[@g_garage]

To podaj to zaproszę na mesengerze

[@dapv144]

I wish you would have listed torque specs.....you seem to have assembled thoroughly to specification. Except for the variator....I think I heard you grunting on the one.

[@g_garage]

On the internet I found a service manual with torque specifications. I tightened the variator without a torque wrench Ha ha

[@raztorreto2003]

@@g_garage do you have the link pls

[@GYccUsefultips]

What size belt are you using on the video?

[@g_garage]

I don't remember sorry

[@ragehd2002]

the belt for the cvt?

[@ragehd2002]

If it is for the cvt than it is with a 10 inch rim a 699mm and for 12 inch rim i dont remember but there are only 2 types for the 139qmb

[@g_garage]

Thanks for the explanation😁

[@ragehd2002]

@@g_garage you're welcome😉

[@leeverink32]

Chains do not last a lifetime replace them to avoid valve chatter!

[@ja-qb9jq]

Nie dałeś oringów pod pompę oleju

[@g_garage]

No później sobie przypomnialem, mój błąd...

[@riadhch5643]

Thank you

[@hwlberd]

bro replace variator fan its all broken

[@kumarjohnsondebbarma1674]

Variator gy6 Mahindra rodeo fitting into

[@progaragechinskiemotorki]

kurcze treba było doczyścić ten silnik lepiej :D zobac u mnie na kanale heheh

[@g_garage]

haha to stary skuterek składany byle jeszcze pojezdził, zobacz filmik z yamahy gdzie silniczek wyczyszczony luxus, a jesli bym nią nie jezdził w terenie to bym nawet wypolerował te kartery :D ale po pierwszej jezdzie w piachu juz znika wiec się mi nie opłaca :D no ogladałem u ciebie pare filmikow pozdro 😁

[@antro-vlog]

best

[@graphonex4457]

Niceeee from morocco

[@LuciusIsaac-s7p]

White Cynthia Gonzalez Helen Williams Eric

[@leeverink32]

Thats plastic dude! Re-using a broken belt..... come on!

[@armsehlich22]

rings under oil Pump!!!!!!!!!!!!!!!!!! you f orgot it!