How to install a defiant motion light

[@smokeyjoe6517]

Now that’s a good video! No BS no music. Right to the point. I just bought this thing and based on your video I feel confident I can install it. I hope I don’t electrocute myself.

[@paulporras9642]

But the video is only set to the wall

[@stkbkr1]

Thank you so much, ya saved me $150 bucks!

[@corylaprade1596]

Great video and very helpful. I have life insurance, so my wife said I can try to install it first. I am furthest from a handyman, but this product looks too easy so I hope success.

[@CMBJASON]

Thanks. That rubber screw cover was what I was looking for. I had no clue how to get this off. I thought it was twist and pull. Thanks.

[@lubovgeorgeable]

Changed these same lights out twice now. Power goes to the baseplate but lights will not come on. Buying different lights soon. Thanks for the nice video though

[@HighRidgeHandyman]

I changed mine out to this model. SO MUCH BETTER QUALITY! Actually look better without one issue to date👍🏻 kzbin.info/www/bejne/f5OoZaCXdrR9m7Msi=N0AyvE2OeH-Sqr2_ I also have a video on repairing the fixture if you choose to try and fix before replacing kzbin.info/www/bejne/pH25XoWXeNSdjM0si=kJsenOrTNwDZUxyR

[@danf321]

Thank you. Just bought this and couldn’t figure out how to remove that inset back plate, until you mentioned the front screw that holds it on. Funny, the instructions state “Don’t remove this screw.”

[@FletchyDog]

The instructions aren't too clear. They mean that it's "captive"....once you unscrew it all the way, it is still held in place on the light assembly. The instructions mean don't try to remove it from the light assembly once you have unscrewed it all the way. It's designed to stay in place so it's easy to get it mounted to the base plate cause the screw is still in position (captive) on the light assembly.

[@JohnBauman-h6d]

the first one lasted me about one year and the second lasted 4 years. The motion sensor become progressively less sensitive.

[@martingainty9623]

I have defiant security light with batteries but cannot locate battery cover...good for another video for DIY Good Video BTW

[@idsullymichaels]

The light is EITHER dusk-to-dawn mode OR motion mode... to switch modes, while light is on for 1 minute+, switch it off-on-off-on (all within 3 minutes) and that change the mode. Haven't yet found out how to adjust light sensitivity...

[@danielramirez-ko9et]

What if only wants to use the sensor by itself, what should I do with the two black cables that runs through each socket? Thanks for your help.

[@t.s8113]

Thank you so much for your video. It was very informative and helpful. One question, I have a ground wire also; does the wire (white and yellow) go behind the ground screw or around it? I can't seem to get the ground screw out of the plate. Appreciate your help.

[@arhurpereyra1567]

I have this set up, it was there when we bought our home. If ibuy the same one I basically remove the old one and plug the new one in? That's what it seems like I could do

[@dholfactory5878]

Thank u my brother for this video helpful

[@iamheheisme1963]

Great video just brought my own ready to install now ...... Yo sunny lol

[@HighRidgeHandyman]

Juda HasAWaken good luck. Be safe. Thanks for watching 👍🏻be sure to catch me live Wednesdays @ 8pm. Workshop Wednesdays where you can ask just about anything home improvement or repair👍🏻👍🏻👍🏻YO SONNY!!!

[@rb0b836]

Thanks pal

[@ladyewo6778]

Hit that little freaking thumb thing. 😂 OAN..Sonney has the sweetest eyes. 🥰

[@HighRidgeHandyman]

Lady Ewo thanks👍🏻👍🏻👍🏻

[@danbrown3460]

Hi Handyman great video. Question-do you think it is necessary to caulk around the fixture to the siding?

[@HighRidgeHandyman]

I would to keep things as dry as possible.

[@yasirahmed4788]

Does it need to connect ground (earth) wire too along with hot and neutral wire?

[@HighRidgeHandyman]

Pig tailed a ground wire from box to ground on light. Was cut in error during editing

[@bradyf9168]

First, locate and turn off the breaker (it will probably be for several items, not just any particular light fixture). Second, turn off the switch in the house and tape it as advised. The only other thing I'd suggest is to install the ground wire first, then the neutral and hot. I know this is a three year old vid, and it is well done in general, but just had to mention the above.

[@chrisgraham2904]

I just installed this same fixture. The product says it will sense motion up to 40 ft. away in an arch of 180°. I've adjusted the "Sensitivity" knob and positioned the sensor ball to all possible locations, but the unit only detects motion within about 15 feet, in an arch of about 90°. Will be taking it back to the retailer (Home Depot) to exchange for a different model.

[@HighRidgeHandyman]

Chris Graham mine will pick up around 35 ft but I don’t have it in arch. To bad it do work. Good luck with the next pick👍🏻

[@purpledancerbmw5279]

At least yours comes on.....ours won't????

[@patl2699]

How do you install a light if I don't have the thing you plug in into how can I rewire it . ASAP please I have two but don't have the the thing you plug the lights to .

[@patl2699]

Does anyone know how to rewire the to wire directly to the electricity

[@ShutItDownnn]

We have this light at home but how do you change it out once it dies?

[@HighRidgeHandyman]

You would have to replace the entire fixture if the light goes out. Unless you want to try and repair it. I have another video on how to repair a broken light in the fixture. Check it out👍🏻 kzbin.info/www/bejne/pH25XoWXeNSdjM0

[@amygray5952]

Can you replace bulbs on defiant? If so how?

[@HighRidgeHandyman]

No you can not replace them. You will have to replace the fixture itself or watch my repair video. Good luck kzbin.info/www/bejne/pH25XoWXeNSdjM0

[@vinceleone8003]

Can you use it with an optional switch??

[@HighRidgeHandyman]

@@vinceleone8003 if you want to use it like a regular door light you have to flip the switch a few times to stay on. Check on a few other defiant videos on programming this fixture. Good luck

[@dianacory2359]

Anyway you can help me make it but stay on at all times ?

[@EverydayMaga]

Do u know how to remove bulb screen to replace light inside

[@robertkenney6002]

No ground wire to green screw?

[@HighRidgeHandyman]

Pig tailed from the box👍🏻 caught it after😳

[@Franco1395]

Thanks for the video. Nicely done. Found your video cuz I have the same model installed for about 2 yrs but one light is out, the other is blinking. Found the manual on manualslib, now I’m looking into bulb replacement or warranty replacement.

[@HighRidgeHandyman]

Frank thanks frank. Good luck👍🏻

[@Franco1395]

@@HighRidgeHandyman thanks. Looks like there’s no easy bulb replacement but there is a 5 yr warranty. I’ll be removing and returning it. I’ll queue up your video again before I replace mine for a little added confidence.

[@mouf406]

Got exactly the same problem with mine.

[@jdorney70]

Hi there. I just installed two of these lights during the day. It comes on when I set it to test for 10 seconds, but when I turn the dial to adjust time they won't come back on. Do they only come on when it's dark? Thanks..

[@HighRidgeHandyman]

You can use test mode during the day. After you set the mode and time they come on at dusk

[@maryannbeals8679]

How to remove mounting plate

[@HighRidgeHandyman]

If from the actual fixture loosen screw tap it with screwdriver to pop the mounting plate off. If looking to remove mounting plate from wall unscrew it

[@ezequielavila9589]

How do you program it to dusk to dawm?

[@FletchyDog]

It's dusk-to-dawn by default. You can control whether it's "always on (in the dark)" or "motion sensor activated" (again, only when it's dark out) by the 3-times-in 3-seconds thing with the light switch.

[@Scottol4530]

How do u change the bulb if it goes out

[@HighRidgeHandyman]

Aquil Scruggs not sure if you can. Some models have to replace entire unit. If I find out I’ll get back to you👍🏻

[@christopherliguori8719]

Great video, thanks. If you don’t have a ground wire, are you supposed to wrap the black around the ground? I’m taking down my old one tomorrow so not sure what to expect but the instructions for the ground confuse me

[@HighRidgeHandyman]

If you have a metal gang box with metal clad romex you can screw a pigtail right to the box for a ground

[@losvalis9851]

Thank you!!!!👌🏼

[@noahreed2920]

is there a way to make the light stay on for longer or on forever because mine turns off within a few seconds

[@HighRidgeHandyman]

Check the knobs on the unit you could still be in test mode. If not turn the dial to how many minutes you’d like it to stay on I think up to 10 minutes. Also check the sensitivity knob. If you want it to stay on flip the switch off for half a second then turn back on it should set it to permanently on until you flip the switch to off. Sometimes it takes a few tries for that feature. If all fails then try resetting unit. Flip the light switch on and off 4 times then leave off for 5 min. That should reset unit. Good luck

[@noahreed2920]

@@HighRidgeHandyman ahh I got a cheaper model defiant but it doesn't have any screws or settings the manual said just flip the switch 3 times and it will stay on for 6 hours or until sunlight

[@dorissandovalgarcia4418]

I would like you show all things you work on it because I couldn't see all steps, I bought one and I don't know how i can installing

[@nitawilliams9726]

Thank you!!!!!

[@ep2418]

Was there no ground wire?

[@HighRidgeHandyman]

There was. I had to screw pigtail to the box and use that. Sorry I didn’t show it

[@431cruiser8]

I have this same light on a new construction. I flipped the switch quickly to get them to stay "on" until I turned them off for the front lights and the rear ones, which are on separate switches. To reset them, I did the "on/off" four times, then off for 5-7 seconds, and then back on. This leaves the lights off until motion activated. This worked for the back yard lights, but I cannot get the front ones to turn off without turning the switch off. I have tried numerous "on/off" quantities and number of times. Is there any other way to reset these? Thanks.

[@HighRidgeHandyman]

If flipping the switch on and off 4 or 5 times doesn’t work try turning off the breaker at the panel for a min or two and try that. Good luck and thanks for watching Cruiser👍🏻

[@431cruiser]

@@HighRidgeHandyman Thanks for the quick response. I should have mentioned that I had tried the breaker already. Do you know of a reset button on the light itself? The only other thing I know to do is disconnect the lights one at a time and see if that does it.

[@shaynanicolle5417]

Can this light be used indoors for a shared hallway ?

[@HighRidgeHandyman]

If you wanted to but it would’ve really bright unless it’s a big hallway.

[@charbar9331]

I have this light and it worked fine for about 3 months. Now there is a red light flashing on the sensor and the lights do not come on at all. Any tips on how to fix this?

[@HighRidgeHandyman]

Try turning off the breaker for 5-10 min and switch it back on. See if the sensor resets. If not it could have go damaged durning a storm. If so it’s replacement time. Good luck be safe👍🏻

[@glennwoods3812]

No ground ?

[@HighRidgeHandyman]

Ended up pig tailing off the metal gang box. the one thing I missed when editing video

[@MustakaBAM]

Curious why you didn’t add a ground pigtail to the back of the metal box to the fixture?

[@HighRidgeHandyman]

MustakaBAM your quick! I did put the tail in after editing in video. Can’t get nothing by you cuz👍 stay tuned to my next bonding and grounding video.

[@MustakaBAM]

Lmao. “Bonding and grounding”

[@weekendhomeprojects]

What kind of camera ya using?

[@HighRidgeHandyman]

IPhone at that time

[@weekendhomeprojects]

@@HighRidgeHandyman wow..that’s good footage for a phone. I figured it was a DSLR due to the quality.

[@Marilynsj]

Installing this light and ran into wiring that has two blacks and two whites??? Not sure what to do…they don’t seem to fit on the holes

[@HighRidgeHandyman]

Look up how to pigtail electrical wiring ti get an idea. I advise you hire an experienced electrician to complete your install. Safety first and foremost 👍🏻 good luck

[@robmartinez8460]

Is this light automatically on dusk to dawn mode? Or do you have to set that up somehow? Thanks

[@HighRidgeHandyman]

It has both options. I have it set to come on with motion and it’s stays on for 5 min. Thanks for watching Rob👍🏻

[@ezequielavila9589]

How do you make it dusk to dawn?

[@chrisgraham2904]

When you set the top dial to "test", that turns off the dusk to dawn mode allowing you to test the light during daylight hours. When you turn that dial to select the "time on limit" (one to ten minutes) the light automatically goes into dusk to dawn mode.

[@MichaelMickeyWilliamsJr]

Chris Graham thank you

[@crecencioperez3038]

Thanks broo

[@miltoncarrillo1184]

Porque no me enciende esta luz.

[@blaxzidk6514]

Thank you

[@miltoncarrillo1184]

La e conectado corectamente y no enciende. Alguein me puede ayudar.

[@JERCHROME]

Is it pretty bright at night?? hmmm...

[@HighRidgeHandyman]

Not bad at all.👍🏻

[@JERCHROME]

@@HighRidgeHandyman i bought the same one and installing tmrw, ty

[@DonBryantPhotography]

I cant get the base off. There is no screw installed. Should I return it? I wish you had at least included a shot of the base or unit to show what to dissesmble. Now I know that should be a simple step but something is missing from the kit or the base also no instructions in the box. Sorry to complain.

[@HighRidgeHandyman]

Bring it back asap! Sounds like someone already had it and took a part and instruction’s out. Good luck👍🏻

[@matthewdennis9699]

Thanks.

[@HighRidgeHandyman]

Matthew Dennis your welcome Matthew 👍🏻

[@matthewdennis9699]

@@HighRidgeHandyman I work nights I was tired after work but I wanted this light up because someone broke into garage. didn't see that screw and this thing came with no instructions and I did want to break it. Was a straight forward video. Glad I didn't have to mess with wire nuts and connections wanting to come loose.

[@texasmexican4795]

I have the same sensor light, can i leave it on test?

[@chrisgraham2904]

Yes. You can leave it on "test" and that overrides the dust to dawn mode. The lamps will light whenever there is motion, day or night. The dust to dawn mode just saves energy, preventing the light from operating during daylight hours.

[@purpledancerbmw5279]

We can't see the buttons your selecting. Camera is moving. My light is all of a sudden staying on. Is it the moths????

[@HighRidgeHandyman]

Did it ever go off since you first installed it? If so someone must have flipped the switch inside a few times to activate the stay on feature. Try turning off switch for 10 min then just flip the switch on and see if it stays on or goes out after a few min. If it turns off in ten min or so it’s reset. If it stays on then you need to adjust the - sensitivity little dial on the fixture. Also sometimes if you have a lighting storm or power surge you can damage the sensor altogether which means total replacement for this particular fixture. Good luck👍🏻

[@purpledancerbmw5279]

@@HighRidgeHandyman thanks sir. Yes it worked just fine. I think It was me who turns it off and on. I'll turn it off for ten minutes but it stays off all day long wouldn't that reset it? My roofer replaced it in March and it was great. Durn durn durn. Thank you

[@lifeitshort]

First thing should be to chk switch or breaker is switched to the Off Position..come on Safety First

[@auletjohnast03638]

DOES DEFIANT MOTION LIGHT MEANS THAT THE LIGHT FIGHTS BACK?

[@HighRidgeHandyman]

john alt Yes it does when I installed this light I turned around to grab a screwdriver and it kicked me in the back of the head with his boot!

[@HighRidgeHandyman]

john alt ive been told you have to replace entire unit. Good luck👍🏻

[@kingofthecrease30]

you got the rocky gloves on or are they just worn out 😂 yo sonny !

[@HighRidgeHandyman]

kingofthecrease30 they come with a few fingerless kid👍 yooooooooooo sonny!

[@randyabdalla3488]

What happen to ground wire ?????? You forgot that

[@HighRidgeHandyman]

Had to run a tail off the box to the fixture 👍🏻

[@jdorney70]

I should have read all the comments. Thanks all.

[@auletjohnast03638]

WHAT HAPPENS IF YOUR WIFE OR KIDS TURN THE LIGHT SWITCH ON FROM INSIDE WHILE YOU'RE WORKING ON THE LIGHT FIXTURE?

[@HighRidgeHandyman]

john alt my hair stands up straight!! It’s happened a few times already.

[@Fremen02]

I can't get the center screw to catch. The light is on but without that center screw it isn't secure. Really dumb design. My wires are heavy Guage. Old house maybe thats why. They didn't leave enough room for that. Really frustrating. So called easy connect system is crap

[@HighRidgeHandyman]

If you have thicker gauge wire on an older house take 14/2 wire and just pigtail ends and use the smaller gauge wire so you can fit the screw in place. Tuck the old wire connected to new tails inside box. Then feed the smaller gauge wire into front light connection point. Much easier to work with. Then you should be able to connect that screw securely. Good luck

[@jimspaulding1738]

WTF, THE IMPORTANT STUFF YOU ARE NOT SHOWING

[@HighRidgeHandyman]

@@jimspaulding1738 put your glasses on bro and watch it again👍🏻

[@dewayneolson476]

When you doing a video you need to have the camera focused on what you are doing the trees or the or the screws . This was a fail as far as my neighbor and I are concerned.

[@purpledancerbmw5279]

Thanks, the guy put it up like you and it doesn't work ???👀

[@HighRidgeHandyman]

We call that USER ERROR😂 find another guy👍🏻

[@purpledancerbmw5279]

@@HighRidgeHandyman I think it's the unit.

[@purpledancerbmw5279]

@@HighRidgeHandyman it works, he tightened the screws more with that ridiculous screw driver. It's pretty......the black matches my changed roof. Praise God.

[@1point9and1half]

Looks like an interior electrical box not an exterior box. Dude what's going to keep the water out? You need to caulk that puppy!

[@HighRidgeHandyman]

Caulking all outside Receptacles and lighting fixtures coming soon. Still haven’t finished editing. Stay tuned in about a week. Thanks for watching 👍🏻

[@oteroluis2010]

Why stay on

[@HighRidgeHandyman]

I can only think of a few reasons . You’re having a party with no interruptions. Or you working in the dark and need it on.

[@loonie3676]

I’m sorry but these lights got to be the shitty lights I have ever purchase do not buy these lights no replacement go out in half a year a wasted time and money.

[@rosalindbrown1300]

i watched to see how you sealed/caulked it but you didn"t.. hum...

[@HighRidgeHandyman]

Caulking in a different video. Hum🤔 but thanks for pointing that out👍🏻

[@EverydayMaga]

Do u know how to remove bulb screen to replace light inside

[@HighRidgeHandyman]

This particular fixture does not come apart to replace bulbs. If you haven’t had it long check your warranty info and return for a new one if you can. I already replaced one myself. And no luck with warranty