How To Install A Remote Start Alarm Completely From Start To Finish on Any Honda 2001 2017 1 HR Vid

[@markstoneberg4558]

This Is the best and only straight forward to the point detailed video. I like how you explain everything in simple terms of what each wire does no fancy pansy technical jargon. You've earned my subscription! You remind me of Scotty Kilmer

[@markstoneberg4558]

:P

[@dhflannagan1]

I don't know if viewers know how hard this is to do let alone to video doing it. Thanks Dude!

[@ry2322]

Its people like you that help me make money on the side to suport my family when a minimum wage job just doesnt cut it! Great vid!! "TWIST IT UUUP"!!! HAHA

[@INCC74656I]

for anyone following along here i have a few recommendations. 1. try to cut off any unused wires back at the brain, less wires to pull up and makes a smaller wire loom you need to pull from A to B. dont pull the wires out tho and dont cut them too short, leave them long enough you can grab them if you ever need to in the future. you can also double them back on them selves to make a service loop and tape it up so no wires are able to touch each other (the ends) 2. dont tape your wire runs all the way up. it makes it a pain in the ass to peel the tape off, tear shit open again when you need to get back in and service. just use a few pieces of tape every few inches to hold bundles together. follow factory wiring when you can and it will still look clean. (if its a security system then sure, go balls out and hide that shit) 3. poke and wrap in this video is intended to be a temporary connection. poke/wrap/solder is better to longevity and proper electrical connection. you must solder correctly however, too much and you will have weak and brittle spots, too little or too little heat and you will have a cold joint. too hot and you can actually burn up wires and have to cut sections out and repair. crimping is also acceptable so long as it is done properly, it can be just as strong as a proper solder job so long as enough pressure is given to cold weld the wires together. a crimp has no ridged areas so it cant get stress fractures like solder can. 4. while its easy to find wires AT the plug the wires all go back to a computer somewhere or at least pass by another area in the dash. you can often find better locations than in the steering shroud to tag your wires and have a shorter run, cleaner looking install, less bulk inside tight panels, and better serviceability (in some cases) by tracing the wires back to a better, more central location.

[@hashishsenju2015]

How about the plastic wire taps sold on ebay. Can I use those to splice the wire connections? Thanks.

[@cliffordstrohm3623]

P.C. i have bin around for over 60 yrs. and bin repairing auto's the same! This is the first comment that i have ever felt i should share my opinion on. To things i would like to share are first disconnect the negative on the battery, and use a high watt soldering iron (30+)and heat shrink on your connections. But other than that well done,also i learned something! TY for your time and the vid. CBS [Trade Master]

[@elmerbotello320]

No nc

[@elmerbotello320]

Switches

[@ronaldmahoney1283]

You made me laugh when you made those beeping sounds! Excellent job explaining step by step in your video!

[@MrKiddo9200]

One thing I learned over the few years I've been installing is all guys with experience always exaggerate how fast they can do an install. haha

[@1wettfloor]

I do it all the time,lol. It will be done in 20 30 mins i just use the rest of the time to make sure nothing can go wrong when your car leaves. Bullshit meter maxed out

[@hectorramirez8055]

to everyone criticizing his connections: a. if you're so 'pro' why are you watching this? As an experienced tech you should know everyone develops their own style. b. you've missed the point of the video. Kudos to you my guy. Clearly very skilled.

[@Lalofelix73]

Great video You got skills appreciate your info I’m trying to learn remote start installs👍🏼👍🏼

[@johnbecht3158]

Hey my remote start is draining my car battery. I need to shut down the remot start. Where is the remote start shutdown switch?

[@mcbillygoat]

Man you got some mad, crazy, slammin skills.

[@RobPGamerVaper]

Dude great Video very detailed. Simple and to the Point. I feel like if I had a Honda I'd be able to do this following you vid. I have a 2000 Chrysler 300M with Factory Alarm and Chip Key But the Factory alarm does nothing to Physical damage which is my concern. When I get enough$ I'm trying to get The Viper 791 or Similar

[@FrankHoneycutt]

It is very practical to solder the wire for many reasons! Also don’t splice into the wire so close to the plug, I would have gone further down the harness. Overall good video for newbies. I really cant stress enough though that if you don’t have much experience with auto electronics to not try and install a remote start on the vehicle!!

[@PrecisionConnections]

Frank Honeycutt. I'll do a video covering why soldering connections are not recommended in the INDUSTRY by Both automotive manufactures and security company. Ask yourself this: why wouldn't they include this method of wiring in modern installation manuals if it was the overall best way to install their products? And also why Can't you find any soldered connections in new cars going back 60 years?

[@rodger6940]

@PrecisionConnections hey bro help me with my remote start please

[@Tierone1337]

@@PrecisionConnectionsof course you don’t have to solder in new modern vehicles because they are not adding splicing into the harness. Everything is planned out. Soldering is best way to splice into wiring . Mechanical connections fail.

[@kmlexso92]

It was a very educational experience thank you 🙏🏾 yeah keep doing them Slow and go

[@jeremy_from_texas]

This is an excellent video! Thank you so much for posting this!

[@rubensilvestre600]

Hi. I find the video is great. Good explanation step by step. I took the viper remote starter out from a 2009 Nissan Altima (Keyless) to install it into a 2008 Chrysler Pacifica. You are working in a Honda CR-V. Wiring is different. I don't know or find the functions of the immobilizer harness wires. From left to right: RED, BLACK/white, PINK/grey, WHITE/light green and WHITE/violet. I don't know what wire is for keydata, lock/unlocked, etc. I will appreciate your help. Thanks.

[@joeyalbergo]

Brother, the best guidance and it all makes sense. I never knew how much really was involved. Lot's of work... thanks again !

[@PrecisionConnections]

Joe Albergo thank bro

[@joeyalbergo]

PrecisionConnections hey the best part that made me laugh was when you were like, "I'm going too make a fast forward version but I'll leave the full version for those of you that just want to be entertained" hahahahaha, that's me !

[@benjaminhanscome7768]

Good informational video. I disagree with the wiring. A few things are shoddy and give a lot of shops a name. I'm a fan of fast turnout as I do custom electrical work for people but I've never in my whole life twisted two wires together and taped them for a permanent connection. I prefer solder but butt splices work great if you use them correctly, and they will always hold better than tape.

[@HOPE-bi5lz]

Hey Bro, I have a 2008 Honda Civic si manual that I need your help installing a universal push start system.

[@Keeping-It-Real-55]

Thanks for the video, i have a 2019 Accord 2.0 6spd manual. I gotta get a remote start installed. I'm pretty handy and don't mind doing this, would rather go plug and play though. Any recommendations on what system I should go with? I heard the Direct 4 x 10 might be a good option.

[@joannejean-louis4059]

Thank you so much for this video. clean straight forward very to the point!

[@mikemilne1954]

Thank you for this video it has helped me greatly as I prepare to install my viper model 4706v with the idata link AL CA in my 06 Honda civic. I do have one question though do you have a video on how you prepare the remote starter harnesses with the idata link module? I want to make sure that I connect everything properly and neat and tidy as I see yours

[@juanesteban8827]

Doing things the right way may not always seem practical, but that's what makes a "professional" a professional. Always solder. Failing to do so can shorten the life of your install and could potentially be hazardous!

[@Chitownster]

Thanks for the video, you put z lot of effort into it. Why didn't you use a harness instead of butchering all those wires?

[@xiaocardot1160]

that is a excellent video,the video show you is a professional installer,I like your Professional

[@missanthrope2]

4:20 ❤😢 Question you never said the door ajar /dome light alarm trigger? Or the proximity trigger? ❤ 😢 sorry if I missed it what time ?

[@ManoochM]

Hi. Great video. Do you have a video installing the same Viper 5305v on a Toyota Camry 2009? Thank you

[@dragonrider9051]

I found this in my truck, was wondering what it was, guess i gotta order some fab's. Thanks for the info.

[@sweatyxsteve5401]

So we have a 2009 Toyota RAV4 and we don’t know which wire is which, how did you know your wires on the car and what to connect

[@xiaocardot1160]

Friend, it seem you are looking for a product like the video show,it is happen to we have the similar product,we have 4G gsm gps car alarm,smart watch car key car alarm ,liquid crystal key,watch key smart car alarm,remote start module...so on. maybe you will interesting in one of them.you can look at my youtube know more,if you like it,you can add me whatsapp: [phone] WeChat：13417625973 mobile phone control car,watch cotrol car,keyless entry，remote start，push start, ... 4G gps mobile phone control car：www.ebay.com/itm/273785328395 liquid smart key control car：www.ebay.com/itm/284267230545 smart watch control car：www.ebay.com/itm/284302869970

[@c230benzito]

Did you make a mistake with the blue and pink wires? I noticed when the video skipped, you had removed the pink from the blue. Just dont wanna make the same mistake and not know wth I did wrong.

[@XellosMetallium]

Can you help me find the wire for the door lock/unlock/trunk release for a Kia Forte 2019? I got the keyless system install. Just need to know where to connect these three wires.

[@isidrobass1374]

Hello how are you, a question, do you need a relay to install PARKING LIGHTS (-) in a 2012 CRV

[@hassanoukaddour9434]

Thanks very much for this great video ! Is well spoken and good explanation of how you doing this. For that... thank you again👍 I just bought one cardot keyless entry and start stop button and will try it to do it myself. Nice work friend!

[@PrecisionConnections]

Thanks Man!

[@pablomarquez4431]

Question. Could you just wire the 1st 6 wires only if u just wanted to remote start only or you got to wire all the other small wires too?

[@craigberube9890]

You need to review and explain the bypass module, the wires you talk about I can not locate on my 5x05 ?

[@Stormnorman15]

I just picked up a Viper 5706v for my 2001 Honda CRV. Do I need that bypass module for it to work?

[@Bugzsbunny1]

Love the video thanks. Now my question is where did you find the information for the colors on the car?

[@kennethmaddux1026]

Can i get a little assistance? I got everything wired up after a rigorous wire diagram search for the V5900( old installed system), the 5806V (new system)and my 1996 Acura Integra. I believe the unit is powered on indicated by the red light on the shock sensor blinking, but the Antenna/Control is not responding. I get no chirp when the ignition is turned to On position and the button is pushed once, let go and held in order to sync the remotes. The system does not seem to be responding to the Antenna. What might be the cause of this issue? Everything is wired up as it should be as a majority of the wires are not utilized for my vehicle. Any assistance would be greatly appreciated. Please let me know.

[@hypetekauto]

thank u for this, made it so simple to follow.

[@jeffreyramos287]

Hello sir, i have a viper 7856 remote starter installed on a 4runner. Can the firing-up/ignition timing be adjusted? It takes about 4sec before it fires-up the engine. Thank you.

[@abdou6003]

Question, I have a CM3000 installed in 2 different cars. While trouble shooting i programmed my 2 way 2w fob to the second car. no its not in "2 car mode" it literately controls BOTH CARS AT THE SAME TIME.. where is the the security? rolling codes?

[@josepaz7286]

How do you install vsm550 to my viper remote start I already have the 5305v and the db4 installed before.

[@wilzedens8676]

Precision connection Do you have a video of the wiring of the immobilizer that you used in this video? I can not seem to find one to help me with my "DIY Installation".

[@710pappy]

Very good tutorial Camera set up was perfect and talk through

[@onway78]

Good evening sir I have a 2018 Honda Civic Sports model I don't know how to get the wiring diagram my question is can I color code the wire that come with my start-up kit to connect on to my car is that the right way to go about it

[@tommyolivas1644]

Need help with a viper 5706 with the 10 pin connector to the ignition. Three red wires what goes to what. Can you help out?

[@jinjara23]

Do you know if that works on other cars also? for example Mercedes benz E class?

[@dirtkingx]

Got a 2016 ram 1500 and having issues on the remote start wiring also and I’m stuck with cutting wires on the ignition switch .. once i try initiate remote start I only hear clicks coming from my db3 module

[@raulanaya4030]

Have you installed the Avital 5105l on a 2018 Jeep Wrangler JL

[@tinkerwest81]

Is their anyway to simply bypass the immobilizer and or security on a 03 honda civic?

[@82Devilz]

Good stuff bro 👊🏼🤲🏼💪🏼💯 nicely done ✅ very simple & explainable

[@KennethT32505]

I'm looking for door unlock/lock wires for a 2009 Volvo S40. I found on the web it said black/red and black/yellow @DDM driver control module but I need to find the exact location @the interior fuse box to connect. Do you know where I can find this information? TIA

[@yosefbeyne8043]

Hey bro Awesome video ..... Am intalling remot starter on my Accord 2000 4 cylinder.. Where The NEGTIVE STARTER OUT PUT SHOULD BE CONNECTED which is the PINK/WHITE on my remote starter? Please help. Thanks.

[@need100peace]

Thank you it’s in fully details and very Neatly

[@Sharky_Mcstevens]

So solder it when it's my car, but use electric tape and send it when it's a customers car at a shop? 🙃

[@jgray7454]

Soldering for installing vehicle accessories is really not practical bro. Unless youre installing a harness that is modular. When you splicing into stuff like for a professional business or even at home this is the best way like he said...

[@blazeaglory]

Ikr? The prelude I bought last year had a nice viper installed but there were all kinds of shorts and the dash lights wouldn't come on. After I bought the car I decided to check out the under dash area... OH MAN WAS IT A NIGHTMARE! I mean the alarm was installed great but everything around it was horrible! Burnt and exposed wires. Disconnected grounds. Random cut wires. Broken interior parts. Etc... It took a bottle of liquid tape, a box of heat shrink solder tubes, 2 rolls of proper fuzzy electric tape, proper splicing, re-grounding factory grounds and replacing entire stretches of wire. It went frm snapping and popping, smoking no dash lights/ dimming head lights, flickering intermittent brake lights, to solid bright quick vivid dash lights ON with NO dimming or smoking Haha Just sucks that the dude who sold me the car told me that the guy who did the work was a solid guy and does all his work. He even gave me his card(which I quickly threw in trash)

[@FazalFariz]

I love to install the 5806V to my car, but I'm confused since I'm worried whether the functions would work with it. I have an 1979 Datsun Sunny which is pretty old car and I'm already using a simple Chinese door unlock/locking system which is quiet unsafe. The doors and the trunk have the actuators installed. Other than that, everything else is pretty simple and needs to be configured manually since I can't find any cables like in new cars. What I would like to know is can the 5806V be installed on my car with all the features working?

[@kennethmanson746]

Hooking up avital 5305L with a DB3 bypass module in a 2000 Honda Accord EX. Was wondering what color wires from the bypass module do I hook up to the 7 pin immobilizer . Problem is there only 5 wires. From left to right Pin 1 blue/white Pin 2 empty Pin 3 black Pin 4 empty Pin 5 white/red Pin 6 white/black Pin 7 white/yellow Also Whitch wire color from the immobilizer do I use to to interrupt the security ligh. Any help would be appreciated

[@IsmailKhan-js5ki]

Please cover on Toyota Carolla 2009 to 2013 model

[@dbrunette3042]

Im trying to hook this remote start up on my 1998 chevy truck. I know this isnt the same vehicle but it should be close. I have a pink with black stripe, a red with black stripe, and red with white stripe left over. Can you help?

[@marielbrotzel]

Are you still in business? My 2007 Ridgeline was declared dead by Honda due to a recall issue. The guy I had bought it from had a remote starter put in which I am in process of removing because the truck is going to be crushed. I have it lowered from the dash right now but unsure about the disconnecting? It is a maybe Viper or a Autostart with two little red modules on top of it called upgradable Xpresskit on them, one is XK01 and the other is XK05

[@Superman12321]

Great video and explanation but one major problem for newbies. since the wires are all bundled up and connected from the beginning, the newbie doesn't know which ones and where the wires are going to the by-pass or starter. I know you explain some things but someone who doesn't know would like to see the connection to the source.

[@PrecisionConnections]

Most Viewer would complain in the comments when we used to include that in the video

[@missanthrope2]

​​@@PrecisionConnections 4:20 ❤🎉❤😢 make 4 part video one undoxing telling what comes in the box. Then show the steps ? What about the door triggers and dome light?

[@missanthrope2]

​​@@PrecisionConnections4:20 0n 😢😢 on a 5706v how do you wire up the sensor to the dome light / slash trigger on a standard no electric windows or door locks. Two door regular cab Truck . and catch both doors.? ❤😮 What about the door triggers and dome lights ?

[@nazarrizvi878]

Great Info. I just bought a Banvie car remote start system. DO you know if anyone sell Tee Harness for for 2015 Honda Civic so I don't have to cut any wires. Thanks. Nazar

[@minnecraftsmn]

I have a Crimestopper RS4-G5. Will this work in an ‘03 Element?

[@ludarican8392]

I have a 2000 honda accord lx. I just want to install a basic remote starter. Whats an affordable brand that can I buy? Also how can I get the wire diagram to install a remote starter for my car?

[@MrDarren1423]

Absolutely great video...CHIEF...I'm looking to do my 2002 Honda accord.

[@Aldo718bx]

Did u ever get the alarm installed on ur 2002 Honda Accord?

[@rallfy01]

good video but what happen to the 24 pin connector didn't show anything on that harness for some people that harness is more confusing

[@johnbecht3158]

My viper system is draining my battery and the alternator will not charge car battery. I need to turn it off. I keep reading about a “shutdown switch “ but I don’t see it anywhere on the system.

[@samuelmccarty56]

He made all the connections properly‼️ He didn’t solder the connections because these are are data wires, and too much or not enough solder can cause the data transfer to not function correctly, also as the solder oxidizes it can cause performance issues on these wires. Canbus and data wires aren’t your old school wiring, these new computer controlled vehicles are vastly different.

[@anthonymarino4260]

A real skill. Thanks

[@marlionisaac8072]

Have you ever install a Alarm System on a Acura Legend 1993?

[@juanmarquez1050]

Yo i feel like i learn something here . I used have the 7142v on my car but I don’t have it anymore so I take of but I don’t know much about what’s the orange wire mean on my remote star wiring ‘ I wonder if you can give some help on that.

[@Keyko5150Estrada]

thank you for sharing your knowledge

[@conga8363]

may I ask one module can we use two antenna and two remote control

[@samyacob2119]

Awesome the best

[@kuttan9321]

First of all let me congratulate you for the amazing video you have done on this. Hi i have a quick question, i recently bough a similar smart start system for my 2016 Honda Civic manual drive. in the manual booklet provided they have mentioned about extra relay for central lock connection which confuses me. do i need extra relay for my 2016 honda Civic to install it.

[@juniorv9565]

Can I wire this on to my Chrysler pt cruiser 2004 just the way you wired yours on the video

[@nema2182]

Thank you very much I appreciated

[@rodneys9805]

This dude is fire!!!!!!

[@marlionisaac8072]

Have you ever install a Car Alarm Programmable Voice Module on a Acura Legend 1993?

[@myeyes7501]

appreciate the vid and info!

[@MILO20121]

Thx u so much question can u install all those boxes in the truck and just wire them to the front

[@xiaocardot1160]

Friend, it seem you are looking for a product like the video show,it is happen to we have the similar product,we have 4G gsm gps car alarm,smart watch car key car alarm ,liquid crystal key,watch key smart car alarm,remote start module...so on. maybe you will interesting in one of them.you can look at my youtube know more,if you like it,you can add me whatsapp: [phone] WeChat：13417625973 mobile phone control car,watch cotrol car,keyless entry，remote start，push start, ... 4G gps mobile phone control car：www.ebay.com/itm/273785328395 liquid smart key control car：www.ebay.com/itm/284267230545 smart watch control car：www.ebay.com/itm/284302869970

[@shanicebutler4160]

wow I didn't know that a remote start was this involved

[@PrecisionConnections]

15:57 explains the reason why wire we chose to make our connections at the steering column: for the purpose of visual understanding of the overall installation

[@tuffy16]

Someone without experience , 3 days to figure out antenna cable was broken another day to figure out the module was fu44ed , old module only blinks twice not 4 times any idea why? autostart

[@michaelgoodwin8006]

Can you give a few pointers on a compustar 7900as with a blade al on a 2003 chevy silverado 2500hd. Also the same system on a 2009 kia spectra

[@mehosalihovic3813]

Very professional thank you

[@edgetonbeckford4611]

Yo man good video. I'd love to learn to do that and be as good as you .

[@Lambrada_co]

The wire harness on the viper is different than mine.i can't seem to find anything like my viper 7816v.

[@justinrodriguez176]

Does the 2008 Honda Civic lx could work for this video

[@guitarhero5461]

I'm trying to add a tailgate lock to the system but now only the tailgate operates and the doors don't. Any ideas?

[@johnkosheluk1041]

Nice work I usto be a dei installer I worked for a dealership i know how hard some alarms can be nice video

[@BabboDiGaggo]

Hi there. I appreciate this video very much and I am wondering if the all process described will be the same on a 2014 Honda CRV. Can you tell me?

[@Waltertech_official]

Great video) where do you get the car diagrams from?

[@JoseFlores-lu4fw]

Need some help, installing viper 5x05 remote start on my 2008 silverado 1500. Can't locate truck wire and color diagram.

[@ns8623]

Can you use quick connectors instead of stripping the wire like done on the large Guage wires at 8:50 ?

[@poeki8891]

Good job installation is clean! I have the 5904v. I'm getting a "toggle switch off" msg in my key when I try remote start what could be the issue? Tanks for your help

[@missanthrope2]

😮The two pin connector has to have a switch installed. On it or the circuit is stays open😢

[@roslynkyle8555]

which system is better compustar or viper compustar has better reviews on amazon and is a little cheaper. whats your opinion ?

[@DJNICOGENT]

Hey bro where can I get the wire diagram for my car .. its a 03 Honda element

[@chrisgreer1911]

I have the exact same viper system my ? I have a 03 gmc envoy do u have to use the interface

[@GabrielMorales-il4sf]

I need help installing 5706v on my 03 F150. Need to take off old one and install new one same model....

[@azvasamusic7095]

Man I need help with my neutral safety switch.... It looks like i have the same viper mod.. 2001 Prelude.. this is driving me nuts and no info anywhere