How to Install a Snow Performance Stage 2.5 Methanol Injection Kit!

[@SavageProductionsCars]

Thanks to Nitrous Express and Snow Performance for providing me with this kit to install in this video and have fun with for years to come! Visit www.nitrousexpress.com/ for more info on both company's part offerings, and be sure to use code "savage" at checkout for FREE shipping on any order!

[@hunchojames8491]

It’s nice to see some content on snow products!!

[@robinbanks3288]

I have the 2.5 kit on order for my F56 Mini Cooper S. I got the kit with the braided stainless lines and I’m planning on mounting the reservoir, and pump in the engine bay so it’s all short runs.

[@dangerousfandango5943]

Your dad was a cool kid back in the dayz

[@2vgod460]

Your dad has an ice mustang coyote for life!!! Boss 302 mustang badddd assssss

[@gamerman644]

exhaust header wrap on the intake to keep in the heat thats gold

[@SavageProductionsCars]

Thermal wrap actually works both ways, you know. Keeps heat out. Not to mention the pipe is scratched up, so it looks better.

[@seandebottis3276]

Great video, adding the same kit to my Audi s4 to beat the TX heat

[@Taylorek2011]

I used this video for some reference while installing a similiar snow performance WMI system on my '13 ST. While still an overall great video I want to point out that neither of the boost references shown in this video are accurate. The one edited in this video does not match up to my accessport at all. I bought a different sound symposer delete that had the option for a boost reference and that has fixed my issue. Just an FYI for anyone else doing it on a ST. Overall still a great video, bought a guage pod from the same supplier he did and my system is working great!

[@SavageProductionsCars]

The location referenced by the arrow at 29:13 is an accurate boost reference location. I still have it hooked up this way and it works fine. Your access port gets it's boost reference info from the MAP sensor on the front of the intake. That is probably more accurate since it's directly at the intake, but the place I referenced is just at another location.

[@Taylorek2011]

@@SavageProductionsCars That's where I originally T'd off as well. While it read boost, my WMI controller would report boost and thus start injecting when my AP still read vacuum. The WMI controller would be peaking out at my tunes max boost while nowhere near WOT. Just didn't seem right to me.

[@SavageProductionsCars]

@@Taylorek2011 you make a good point there. I see 20-21 pounds if I'm low RPM and just give it half throttle rapidly (which then reduces to 13-14 at higher RPMs). I figure that's just due to the small turbo immediately spooling. But it would be better to measure at the MAP sensor like the AP does. There's a whole system pressure mismatch not being taken into consideration when you're measuring at the sensor which (I believe) regulates boost for the turbo vs. where the boost actually ends up in the system.

[@ocurrenciachapina]

Thank you for showing your installation, Can you please make a video of how your Ford focus ST is doing with the water methanol I will appreciate that, like a follow up video.

[@SavageProductionsCars]

Thanks. I'll see if I can get it to the track this year and get a difference between a run with off and a run with it on.

[@ocurrenciachapina]

Hello quick question is your Ford Focus ST working fine with the water methanol kit you installed? And if is posible can you upload a video I will appreciate that, thank you I like your channel

[@SavageProductionsCars]

@@ocurrenciachapina yeah it's working fine with it. It's not a potentially harmful mod like nitrous (if done improperly). My tank is empty right now and I don't have any extra just yet. I'll get some soon, but I don't know if I'll do a video on it. I might upload something to my Instagram instead.

[@ocurrenciachapina]

Got it thanks for let me know it is working fine I appreciate you answer fast, take care

[@ocurrenciachapina]

Good morning and sorry to bother you again I'm very excited because I almost finished my installation at the way you did yours thank you for sharing this but before I install the motor is safe to install this outside the vehicle rear bottom bridge like you did? and in the engine fuse box there is 3 fuse opening with key sourced any of those openings are ok? You were a life saver making this video thank you very much for all your help.

[@johng2779]

Great video !! Good job. Very helpful.

[@markrosario8800]

Excellent Video! Oddly enough, I am curious what wire loom you used?

[@SavageProductionsCars]

I believe it's Painless Performance powerbraid wire loom. There are others in this style just called "woven wire loom" or "braided wire loom".

[@onceuponasauce8177]

Great video! A HUGE HELP!

[@AtticAZ]

Great video. I’m sold!!! I’ll be getting this for my car.

[@SavageProductionsCars]

Great choice! Tell em you saw it on the Savage Productions KZbin channel!

[@AtticAZ]

Savage Productions will do

[@stephensmith1880]

Awesome video I'll be installing this kit in my 2019 civic type r this weekend

[@milaperegon2787]

Very helpful video... thanks man

[@nstylemotorsportsracing1471]

Amazing video looking into meth and this video is incredible! Thanks for such a great instructional video!

[@2vgod460]

I always thought the gauge was like a super high end gauge option for the water meth kit, but nope the vc50 is just a gauge type controller it’s cool tho, I needed uo ordering that thinking it was better then my stage 3 controller big mistake, lol but I like to have it in my gauge pod but the stage 3 is way more options

[@Gene4666]

Lexus GS300 comes stock with a 2JZ

[@SavageProductionsCars]

Yes, but not the 2JZ-GTE, which is what that car has.

[@genevox2941]

needed to see the plumbing for the water/meth from the pump to intake, which nozzles? 2 port nozzle upgrade?????

[@SavageProductionsCars]

I showed the plumbing. Snow Performance has a chart for which nozzle they recommend for your setup. Dual nozzles are a case by case basis, and talking to Snow Performance themselves would be the best bet.

[@khalidkharraz9007]

Hey, where did you connect the purple wire? It should go to the level sensor but level sensor wires are 2!!

[@lethal_chevy5442]

Hey love the video was very helpful. I am installing my kit now but I need a longer vacuum/boost line what did you use for your extension tubing

[@SavageProductionsCars]

We had extra vacuum line at the shop. It's always good to have some laying around.

[@lethal_chevy5442]

@@SavageProductionsCars so you just used some 1/8 inch vacuum line

[@SavageProductionsCars]

@@lethal_chevy5442 I forget what size it was, but it doesn't have to be large. 1/8 is probably right.

[@SavageProductionsCars]

@@lethal_chevy5442 just whatever you have or you can find that will adapt properly to the provided line.

[@lethal_chevy5442]

@@SavageProductionsCars thank you 🙏

[@FabulousMrCheeks]

nice video, very well done. I found it odd that you were running the stock FMIC with the WMI.. any reason you didn't upgrade the FMIC?

[@SavageProductionsCars]

Because the car is stock, and this kit was graciously provided by my sponsor for advertising/instructional purposes

[@FabulousMrCheeks]

@@SavageProductionsCars Makes sense! After running it for a while on the stock FMIC, did you feel like the WMI reduced the need to upgrade the FMIC?

[@SavageProductionsCars]

@@FabulousMrCheeks I never really felt the need to upgrade anything on the car, so I couldn't tell you. I've waxed heavily modded STs in my stock ST even before the water meth. Driver mod is worth 100 hp in some cases. Lol

[@BimmerHausPerformance]

Thanks for the video, can you confirm if it matters if you install the pump upside down or not?

[@SavageProductionsCars]

It does not matter. As long as the inlet on the pump is below the lowest part of your reservoir and drain system.

[@BimmerHausPerformance]

@@SavageProductionsCars Thanks so much for the quick answer! Did you ever do the follow up video you talked about to get some of your impressions?

[@SavageProductionsCars]

@@BimmerHausPerformance I did not, but that's something I may do in the future

[@mdwdrumlife]

Hey im reading the description on this and its saying for smaller, faster spooling turbos to use the snow performance 212 instead of this one(210). Ive read a few comments of you saying its working great im just checking before i order.

[@SavageProductionsCars]

I've never seen the 212 kit. Looks like it would be a good fit for a smaller turbo, like you said. I don't know if it comes with an on/off switch so you can turn it off when you're not using it. That's one good thing about this kit with the controller as a gauge. Although, you have to get a gauge pod to mount it. So it's really up to you. As long as you select the right nozzle size, they should work similarly.

[@AtticAZ]

Need assistance. How did you connect the VC-50 to a boost source. The line off the gauge is pretty dang small. What fittings did you use? My kit came with a T-fitting. But it’s more for a regular boost line. Would heating the lime off the gauge work? P.S. I watched this video 6 times so far. Love it.

[@talon8u]

Hi Boosted 3.7. What did you use to connect the two vacuum lines together? I’m wondering the same thing and mine came with the little T that won’t even nicely go into the VC-50 vacuum line.

[@Gauges480]

You still running this? If so how had it been? Any issues? Just ordered mine today.

[@SavageProductionsCars]

Yep, still running it. No issues at all!

[@minimanadam]

Just ordered my kit...

[@carbonspeed1050]

How’s the kit holding up

[@pjmprojectman9018]

Watched the entire video very nice content... but I am still unsure if I should go Snow Performance on my S550 Gen5 3.0 Whipple Supercharger.. any power gains, lower IAT'S, will the kit come with all I need... what r ur thoughts!... thanks

[@SavageProductionsCars]

You absolutely should! The power gains will mostly come from lower IATs, which means it's good for back to back runs. At the same time, the octane will be slightly raised with the meth, so your knock sensors will be happier than normal, meaning you may be able to get a revised tune for the meth and run more timing. The difference it makes scales based on horsepower, so your car will really see the effects of it. When we put it on my dad's ProCharged 2012 Mustang, it felt like a night and day difference when we were spreading it vs. when not. The kit will come with everything you need minus the bung to tap into your intake pipe and (I believe) the connectors for wiring. You'll also need zip ties to secure the line and hardware to secure the pump and reservoir.

[@pjmprojectman9018]

@@SavageProductionsCars Super Awesome. Thanks for your quick and detail response. I am really thinking hard about ordering but everyone said it does help/ add power but Snow Performance said it does. Maybe those saying no r "haters"! My IAT's were extremely high last summer here in Ga... so I added a killer chilla but now I want that Menthol for the extra coolant & power..... do u recommend? Thanks I really appreciate you giving me the time and help/support... that's Cool Stuff....

[@SavageProductionsCars]

@@pjmprojectman9018 no problem man! And yeah I highly recommend. When we installed the kit on my dad's car, I was sponsored by Nitrous Express. Nitrous Express acquired Snow Performance sometime after that, so that's how I'm also sponsored by Snow Performance. But I stand behind their product regardless. They have recently come out with a bunch of plate kits for spraying the water/meth instead of using a nozzle and a bung. I could be wrong, but I think the Whipple uses the stock throttle body housing. If that's the case, you could get a plate kit instead which are more efficient and don't require any tapping of an intake pipe.

[@PinksGarage]

Did you mount the pump with only 2 bolts?

[@avidashoalhaven4555]

wasnt the nozzle supposed to be mounted within 6 inches of the tb?

[@SavageProductionsCars]

There's different mounting points for different applications. Further from the throttle body (right after the intercooler) is better for optimization with the fuel, giving you a better blended octane. Closer to the throttle body is better for cooling. I wanted more octane out of it than cooling, so I opted for mounting it far away. I actually ended up having to get a charge pipe to replace my factory one, and it had a welded-in bung which put the nozzle about 8 inches from the throttle body.

[@minimanadam]

I'm disappointed the gauge only reads boost not vacuum...figures , snow skimping as usual

[@ajsracing6318]

What fuse/circuit number did you tap off of for your keyed power?

[@rizzoid]

Out of curiosity, why have your last videos been flipped? Causes writing to be backwards. As for the Snow kit, that pump seems absolutely overkill for the application. Keep them coming, enjoying the videos.

[@SavageProductionsCars]

I'm recording with my new phone now and the forward facing camera flips the video. I need to look into having it record the other way. But yeah this same kit applies to 2000+ hp cars...lol

[@rizzoid]

@@SavageProductionsCars For what it's worth, I use Sony Vegas and it has a setting that'll flip video. Might have something like that in your software. And since it'll do up to 2,000 HP, looks like you now have a reason to modify your ride even more! ("Yes, I really do need those two 88 mm turbos. This poor meth injection pump is totally underutilized! Think of the meth pump!")

[@SavageProductionsCars]

@@rizzoid I make those excuses for modifying my Mustang now...it's a good thing I don't really have to convince anybody except for myself right now. And I use iMovie and couldn't find the flip functionality in a 10 second search, so I'll investigate further.

[@dexterboi9564]

A little late, but where did you get that gauge pod???

[@SavageProductionsCars]

Ortiz Custom Podz

[@DJCRIS3B]

Hi there guys which ignition live fuse did you tap in to please can you help me as i cant find which 1 to use

[@ecobeast3604]

How long does that small tank last? Do you fill it up daily? (If you daily drive with a heavy foot)

[@SavageProductionsCars]

I leave the injection off daily and only turn it on when racing. I've had to top it off once since I installed it and that's only because I was doing a lot of testing with it right after installing. I'd say it would last maybe 50 full runs, if I had to guess.

[@bryanmccool2587]

I'm not completely sure but I don't think Loctite works with plastic parts

[@SavageProductionsCars]

Good point. I believe it eats up the plastic a bit, but I also think it gets worse the stronger the formula is. This was blue Loctite, and luckily I haven't had any leaking issues with it, and it's been installed for about two years now.

[@joelvandiest7027]

I hope people are not just slapping these on and expecting hp gainz 😬 you will lose hp and that's a fact.... you have to tune your setup with water methanol injection after installing...

[@SavageProductionsCars]

Actually, if you're just using it for cooling or even if you have a car that auto-corrects for octane, you'll still make more power without a custom tune. Not to say you can't get an optimized tune for it that'll make even more, but lower IATs and higher octane (usually up to around 93-95 octane on newer self-correcting vehicles) will always make more power. (Clarification: more octane will make more power up to the stock allotted timing increase)

[@SavageProductionsCars]

The trick is to not spray too much and just flood yourself out. This is why Snow Performance offers a chart for the correct nozzle size for your engine size and boost range.

[@milaperegon2787]

Did you order bung and check valve separate? Or it came with kit? Thanks

[@SavageProductionsCars]

It comes in the kit

[@BlackYellow_s7]

How were you able to lengten the vaccuum line from the VC50? can you just pull this out of the controller or do i have to find a nipple socket to lengten the vaccuum line to make it longer?

[@SavageProductionsCars]

@@BlackYellow_s7 I attached another vacuum line to it

[@BlackYellow_s7]

@SavageProductionsCars Wow, thanks for the reply. I wasn't sure if you were still active.🙌🏾

[@SavageProductionsCars]

@@BlackYellow_s7 Yep, just not uploading atm

[@FKfilmphotography]

Does the pump need to he underneath?

[@SavageProductionsCars]

It just needs to be underneath the tank that holds the water/meth. Other than that, you can put the pump anywhere you like.

[@pospc2]

I got a snow sno-210 on the way for my daily 2013 Gti. Where is your shop and do you do cages?

[@SavageProductionsCars]

We're located in Hebron, KY about 20 minutes south-west of Cincinnati. And no, we don't do cages, but we recommend Tin Soldier Racecars for chassis work.

[@pospc2]

@@SavageProductionsCars I am in the Columbus Ohio area.so not too far away. Thanks for the recommendation. I will likely need a cage in the next year or so. Not for my gti.

[@SavageProductionsCars]

@@pospc2 Gotcha. Let us know if we can help you with anything. We are a parts supplier as well. And no problem, we highly recommend TSR.

[@mjstewart69]

At 22.10 the bit u put in the pipe for the injection can u please send me a link to where u go this please I need 2 of them

[@SavageProductionsCars]

I bought the CP-E METHcharge cold side pipe.

[@mjstewart69]

I want the same kind of little fitting he has there as I am fitting my own to my can and need us standard piping and thats would be amazing to have two of those little things in my size

[@SavageProductionsCars]

@@mjstewart69 Snow Performance sells that fitting. We got that along with the kit.

[@eduardopadilla8532]

How long does it takes to empty the water methanol tank

[@SavageProductionsCars]

Depends on how long you have it on, but I'd say about 25 pulls

[@sleepymalo06]

Planning on any dyno runs with and without the snow kit on ??

[@SavageProductionsCars]

Definitely no dyno runs for this ole girl. I might do a 1/4 mile comparison at the drag strip, but that'd be it.

[@jasonss424]

hello... for your power source, did you throw a fuse into that line?

[@SavageProductionsCars]

We hooked in the line directly to a key power on fuse socket in the engine bay.

[@Veau88]

Where did you buy the air vent gauge pod? Ive only found one online but its like 150$??

[@SavageProductionsCars]

Ortiz Custom Pods. Mine was $139.

[@Sonicaceman]

Hello I had mine installed at a shop a week or so ago and it seemed to work good and for no reason the gauge is not recognizing boost. We used the port on my symposer delete, I’m confused it just stopped working Any ideas

[@SavageProductionsCars]

The vacuum hose may have popped off in line somewhere.

[@gabrielreyes6393]

What cable did you connect the in line fuse too?

[@druumoren4458]

+1 I believe its between the pump and controller

[@jasonss424]

I was thinking you need a fuse for the power line going into controller... not a fuse for pump cause if pump fails why would the controller fry? Wiring diagram doesn't show an inline fuse anywhere

[@robertosaenz4635]

What do you guys charge for this install on the 13 st ?? For this system of course lol

[@SavageProductionsCars]

If you're interested, it's better to call or message us on Facebook for quotes. We'd be happy to do it!

[@TheMrmmkkpro]

Hey guys ,I recently bought a 2015 6.2 Silverado , will this injection system work for keeping intake valves clean? Just found out about DGI intake valve issues ,I am running a range technologies AFM delete , and plan on a good catch can. Not worried about hp, just thought this might help carbon build up ,thanks.👍👍🏁

[@SavageProductionsCars]

Methanol should definitely help with cleaning the valves. On this car in particular, I can notice a good difference in performance after I have sprayed it recently. I'll go a few weeks without spraying it, I'll make one hit with the system on, then I'll turn it off again, and it almost still seems to be helping!

[@TheMrmmkkpro]

@@SavageProductionsCars Thanks for the quick reply. I am very concerned the truck has 70k ,very nice ,well kept ,but I know nothing about how the engine was treated. This DGI intake valve thing is not good ,wish I would have known about this before I purchased it. CRC claims to have a product for removing carbon but I've read conflicting reports on that. Thanks again .

[@SavageProductionsCars]

@@TheMrmmkkpro no problem. Yeah there's nothing dangerous about water/meth. This kit is for use with a boost reference, so at max boost, I spray about 50% of the nozzle's capability. A low amount like that won't harm anything. The worst you could do with too much meth is wash the oil off your cylinder walls, but you'd be really flooding the cylinders and noticing a loss of power when spraying if you were spraying that much.

[@collinparks4960]

For the inline fuse, what was connected to what,

[@SavageProductionsCars]

The 12v source from the pump to the gauge

[@collinparks4960]

@@SavageProductionsCars was it a 20amp in-line? I bought my kit used and I’m only missing that.

[@SavageProductionsCars]

@@collinparks4960 we added the fuse ourselves. I don't think it came with the kit. I don't remember what amperage we used.

[@collinparks4960]

@@SavageProductionsCars that’s ok thank you!

[@Nathan-wn5mc]

What kind of mix or methanol are you using? I've heard a lot of people say you can run Windshield wiper fluid.

[@SavageProductionsCars]

I run Snow Performance Boost Juice. It's 50% methanol. You can run windshield washer fluid, but they typically have less methanol content. Also, some of them have a chemical additive that you do not want to run through your engine. So if you want to go the cheaper route and run windshield washer fluid, do your research.

[@Nathan-wn5mc]

@@SavageProductionsCars Awesome, thanks for responding.

[@rexmeadows9681]

What boost line did you tap in to for your gage please let me no thanks.

[@SavageProductionsCars]

Email me at [e-mail] and I'll send you a picture

[@isawul00k]

Loctite reacts to the metal causing it to cure.. its worthless on plastic.

[@grandpa_stinger]

I need help brother i bought a 2.5 kit no instructions. Where do I hook up with vacuum on the unit not car

[@SavageProductionsCars]

The thin black tube coming from the back of the gauge/controller is the boost reference for the system.

[@grandpa_stinger]

My kit only had the gauge in it

[@SavageProductionsCars]

@@grandpa_stinger yes, it's attached to the back of the gauge. It looks like a thick wire, but it's a vacuum line.

[@grandpa_stinger]

Thxs anyways brother mine only has one black anything coming out the back and its the ground wire. Wish i could send you a picture

[@SavageProductionsCars]

@@grandpa_stinger shoot me a dm on Instagram @ThatGrayFox

[@realtalk9648]

are you having a leak nozzle on this product? my aem is having leak nozzle and need to replace everytime have this problem

[@SavageProductionsCars]

No leaking at all

[@realtalk9648]

thank you for reply. ill replacing my kit to this product. i own type r what stage is the best for 400hp

[@SavageProductionsCars]

@@realtalk9648 it would be best to talk to the guys at Snow Performance. They know a lot more about it than I do. Feel free to use the vode "savage" at checkout for free shipping on any order.

[@torvarrisevans3961]

Hey bro , what you recommend this kite for a G37s

[@SavageProductionsCars]

You'll only see substantial benefits of methanol injection on boosted applications.

[@torvarrisevans3961]

@@SavageProductionsCars ok , I have a full bolt on G37s coupe , l live in the Caribbean islands we dnt have high octane fuel . I was just wondering if I decide to get my car tune , will it be beneficial to have

[@SavageProductionsCars]

@@torvarrisevans3961 not really. You'd have to spray a large amount in order for it to really affect your octane levels. You would maybe see a 25hp difference if it was tuned correctly for it.

[@torvarrisevans3961]

@@SavageProductionsCars thank u

[@mcfly727]

Update ? How much of a difference did this make after tuning?

[@SavageProductionsCars]

The car doesn't have a tune on it. I don't think it does much for this setup untuned. I've been wanting to get some real before and after data with a few friends whose cars are always dead even with mine. I think if anything, it helps it up top in 3rd gear onward because the IATs remain low throughout the pull.

[@micp8700]

Hi what size Snow Nozzle did you use? The number 3 or number 5 ? Thanks

[@SavageProductionsCars]

I chose the white nozzle, I believe. If I remember correctly, they send you the nozzle you chose, as well as one size smaller and one size bigger.

[@micp8700]

@@SavageProductionsCars ok thanks i have the Snow #3 nozzle in my Focus St in throttle body spacer, also where did you get the Vent Pod holder for the gauge? Thanks again

[@SavageProductionsCars]

@@micp8700 check 4:30 in the video. I got it from OrtizCustomPods. I ordered through Facebook, I think.

[@micp8700]

@@SavageProductionsCars Hi Thanks ok will check it out 😀👍

[@DavidDiaz-vi1xx]

Mine kit is not working. Did you install the solenoid?

[@SavageProductionsCars]

There is no solenoid with this stage kit.

[@DavidDiaz-vi1xx]

@@SavageProductionsCars 😳 the shop i took it to installed one . They also installed the pump in the engine bay and the tank in the trunk

[@SavageProductionsCars]

@@DavidDiaz-vi1xx it's might be a different stage kit then.

[@justinhinsey4093]

How is this holding up?

[@SavageProductionsCars]

The kit is great. Had a small failure of the check valve, but other than that, all the electronics are great. My dad's, which he installed (I think) 2 years prior to this one is working great as well.

[@justinhinsey4093]

@@SavageProductionsCars Awesome thank you.

[@justinhinsey4093]

Also meant to ask. How are your pistons and piston rings holding up. I've been hearing a lot of failures because of the methanol breaking down the oil? But obviously if it's been a couple years you guys aren't having that issue. Any advice or feedback on that issue would be much appreciated.

[@SavageProductionsCars]

@@justinhinsey4093 I haven't had any issues with that

[@SavageProductionsCars]

@@justinhinsey4093 that sounds like something that could happen if the mixture is too rich. The same could happen with any fuel, and can often happen when you have a leaky injector.

[@minimanadam]

I thiiiiiiink you did that gasket wrong

[@SavageProductionsCars]

If you're talking about the plastic bung, then yes. I drilled too big of a hole.

[@NhungNguyen-mt7gn]

How mane

[@minimanadam]

I just STOMPED a focus rs in my modded mini

[@SavageProductionsCars]

Good for you. This is an ST, which is even slower.

[@minimanadam]

@@SavageProductionsCars How are you liking this kit ??? I just order the same one for my mini

[@SavageProductionsCars]

@@minimanadam been working great. Recently had a little failure with the check valve so it dumped all the meth in the tank into my charge pipe, so that was fun. Other than that, all the electronics and everything else has been working great.

[@griffon3275]

Unboxing? description on the 1 gallon meth tank ? you can drill it to install a float ? just came here after watching product videos on AEM injection and not only do you not have to add a float but they use sensors which is a float upgrade and this fucking kit doesnt even have a HEY your out of meth in your tank warning system your gonna blow your motor cause its tuned to run with meth ?? not buying this shit .. how much extra you gonna charge for a basic necessity of adding a float ?

[@SavageProductionsCars]

This was an install video, not an unboxing video. If you want to see what comes in the kit, you can look at their website. The kit does come with the float seen in the video. The reason the float isn't pre-installed into the tank is because this kit gives you the option of using a different reservoir for the water-meth. My dad installed the same kit on the Mustang featured at the beginning of the video, and he used his windshield washer fluid reservoir. The whole purpose of the float is that it connects to the gauge, which does warn you when you're running low.

[@stickytireproductions7516]

Hello i just ordered this kit from panda performance but my question is does it come with the check valve or is that ordered separately?

[@SavageProductionsCars]

It should come with the check valve. Check the part number on nitrous express's website.

[@jeremy5641]

So does the kit come with this gauge? I know it comes with some type of boost controller

[@SavageProductionsCars]

The stage 2.5 kit comes with this guage, which is also the controller for the water/meth injection, which works off of boost. It's not really a boost controller.

[@lettuce9612]

Hello, what does each color on the gauge mean?

[@SavageProductionsCars]

You can change all the colors. There's no specific meaning to colors.

[@lettuce9612]

@@SavageProductionsCars also did you implement the solenoid into your setup at any point?

[@SavageProductionsCars]

@@lettuce9612 no