Consider supporting our work on Patreon: / buildingwithbudd to help us make better quality videos! This is how to install pre-stressed lintel
Пікірлер: 46
@justice007willprevail2 жыл бұрын
Amazing job, and even more remarkable is the time you spent to share your knowledge. God bless you brother!
@BuildingwithBudd2 жыл бұрын
Rob many thanks for watching 👍👏👏
@prozachblinded-butterflies55309 ай бұрын
Don't you own any tuck pointers Like literally you could probably tuck that in a little better with The right tools it looks like you're just surface pointing you aim to get nothing towards the back half I would give you a low score on your quality plus you're using the wrong type of mortar way too much cement for that **** old building
@neojted4 ай бұрын
You mentioned slate a couple of times but I couldn't quite make out what you were saying. Was there more to do or is the job finished?
@TheMundin13 жыл бұрын
Very helpful!
@BuildingwithBudd3 жыл бұрын
Thanks for the feedback, be sure to stay subscribed for more videos. Lots of stuff planned! 😀
@brianobrain898514 күн бұрын
Nice job Budd. I have a problem with an aperture in an old stone wall in France. The stone blocks are sitting on a massive wooden lintel which is half rotten. I intend to support the lintel from below but I cannot take it out nor can I change the fact that the lintel might well disintegrate over time leaving a huge gap. Any ideas anyone?
@BuildingwithBudd13 күн бұрын
If you could send some pictures we could have a look 👍
@ManontheOutside2 жыл бұрын
Me, cutting one brick : drive to DIY store, buy a grinder, cutting disc, dust mask, ear defenders, gloves, goggles, extension lead; spend 10 mins measuring brick, 10 minutes cutting brick. Cost = 200 quid, time = 1 day Budd the builder: casually whack the brick with trowel, cuts perfectly, already had the trowel. Cost = zero, time = 5 seconds 😂😂😂 Top job mate, great video👌👌👌
@BuildingwithBudd2 жыл бұрын
Many thanks for watching 👍
@mrblack61 Жыл бұрын
Thanks Budd, this is exactly what I have do after changing out a small window in a 9" wall that had no external lintel. The bricks above it were near the roof and all loose. Cheers for the lesson 👍
@BuildingwithBudd Жыл бұрын
Many thanks for watching 👍
@jezzyby47 Жыл бұрын
Brilliant again, you don't live in Yorkshire do you? I could do with you for some work that needs doing.
@BuildingwithBudd Жыл бұрын
Thanks for watching 👍
@GrantGunTV3 жыл бұрын
Use a tuck pointer for pushing in the mortar, much easier to ensure all muck gets to the back of the brick 👍🏻
@tlee89472 жыл бұрын
it looks a soild wall, what about behind the lintel? will be 2nd lintel behind the first one installed? please advise.
@BuildingwithBudd2 жыл бұрын
It’s a 9 inch wall , we put the 1st lintel in then let that go off, then we can cut the hole out and install the 2nd lintel, Cheers for watching 👍👍
@user-cn1em2qx6f Жыл бұрын
if if wasnt going to be rendered is a concrete lintel still ok to use. or would you recommend a different type of lintel. i am raising a door opening with an arch and dont know what is best to use as its built in lime
@ronaldlangley2592 жыл бұрын
Why cement, when the rest appears to be lime?
@BuildingwithBudd2 жыл бұрын
If it was face work we would use lime, but it’s all going to be covered up so there was no need to go that route, many thanks for watching 👍
@strummer664210 ай бұрын
Great video. Does a lintel need to sit on a padstone?
@BuildingwithBudd10 ай бұрын
This particular lintel didn’t , your average lintel over a window wouldn’t have one either, if your not sure have a look at the specifications on the drawings, Much appreciate you watching the video 👍🧱
@michaelbennful3 жыл бұрын
This is great! Thanks Budd. Love the trick at 8:00 to get the brick to shape.
@BuildingwithBudd3 жыл бұрын
Thanks!
@rjb26265 ай бұрын
Bteer use a poining trovvel next time...
@Batsahead3 жыл бұрын
Hi, I have a double brick house I want to access under it from the underhouse garage. My walls are also all brick. Would my wall run down all the way to the ground. The floors seem to sit on the side of the walls and not run under them. Hence I want to get under. They put an extension along the back 4 foot from the main building but go down stairs through what looks like the old toilet. So it’s dropped down and they just left this tiny access hole under the boiler between the house. I’ll get stuck in it for sure. Q: if I cut into the brick via the carport I’m thinking it may be double brick. How can I support the back layer of bricks by using this method as it only supports the front layer? Know what I mean ? Also wouldn’t I be better using an I beam. I’m thinking the bricks run all the way down to the earth, so would under my house be exactly the same as if I was walking through it as the floor plan above yeah? So I’ll cut under the house where the hallway is yeah? Massive long hallway. I play bowls in it.. ;) so that would be my bet bet to access the rest yeah ? If I knock the first bricks out to put the ibeam in what do I do about the second behind it ? Knock them all out at once? Cause I get round the other side.
@karlmullowney9985 ай бұрын
THUMBS DOWN : WHICH SIDE UP ???????????
@matthewspry421710 ай бұрын
LOOKS F IN GREAT FROM MY HOUSE
@Batsahead3 жыл бұрын
I can’t quite hear you properly, two day time you’ll take the first bricks out, then how will you get at the back to put a beam in ? Also why won’t that beam crack ?
@chrisbirchall28763 жыл бұрын
Has pre stressed metal rods through it
@chrishamilton35822 жыл бұрын
it doesn't need an acrow support while you are doing the work?
@BuildingwithBudd2 жыл бұрын
If you know your work, using individual lintels is a great way of not having to use an Accrow, but it’s only my way I do things, cut the first one in, cement it in , then let it go off, then cut the other one in repeat the process, job done.cheers for watching 👍🧱
@meejhgggg3 жыл бұрын
If u do the same work but grand floor door opening, dont need any support to prewent crack? Inside block.
@BuildingwithBudd3 жыл бұрын
Always best to put more support in than needed
@ACE9993 ай бұрын
Budd for PM!!!
@topcatcoolio88073 жыл бұрын
Finger, or margin trowel useful Bud. To push the mortar home. Top man
@buildorder06 Жыл бұрын
Every such opening should have a cavity tray to direct any penetrating rain water to the outside.
@BuildingwithBudd Жыл бұрын
I guess you are not in the building trade it’s a solid 9 inch wall and it’s ending up being the inside of a room, cheers for watching 👍
@prouserprouser964611 ай бұрын
Solid wall! Delete your comment if I were you !
@dimitardobrev329610 ай бұрын
I've got a tricky one and can't seem to find a video on it, does anyone know how to do this for a single skin brick wall? I need to install a 600mm wide window but don't know where to start. If I take out the lintel course I'll have around 4 - 8 courses above supporting rafters (roof is mono pitch and low). Thank you.
@Romanchelli-ci9on7 ай бұрын
Did you manage to sort it? I’m doing a door in the external wall, planned to use acrow props and some “strong boys” above where the lintel needs to sit
@dimitardobrev32967 ай бұрын
Nope not yet - been dealing with storm water channels (rainy season) - the window can wait. I reckon if its done quickly (cut, bash, grout in new lintel all in one session), there will be no time for settlement and it should be fine. @@Romanchelli-ci9on
@garytango Жыл бұрын
👍
@saveirodiesel2 жыл бұрын
Valeu Bud. Essa contraverga ficou legal.
@BuildingwithBudd2 жыл бұрын
Edval many thanks for watching 👏 where are you watching from ? Keep well 👍👍