The Hive Mini is set up out of the box for use with a Hub, the method of operation as described in this video is "standalone mode" as explained at the end of the installation instructions .
@paulwatkins15 күн бұрын
Hi Mark, great videos on the hive installs - ive wired mine in and all conected to the phone etc - (stand alone boiler Y set up with 3 way valve) - green lights coming on for water or heating as they should on the receiver - but heating only is not firing the boiler - water only is bringing hot water and heating on together - what have o done wrong? any help please.
@stephenkirk11542 ай бұрын
Just bought my first house and I’m trying to install my Hive mini set up into the existing ideal iMini boiler. It’s already set up with a Drayton Digistat+2 which is connected with a three chord flex but the earth wire isn’t connected to anything. My question is - will everything work fine if I just replace the Drayton with my hive and use the three chord flex and wire it up as you’ve shown ? What’s the benefit of using the switch wires ?
@VBScab6 ай бұрын
Hi, Mark. I'm pretty confident that I can replace my WR1 with the Hive receiver - it looks as if it'll just literally drop on - but am unsure as to what to do with the old British Gas (Drayton DigiStat) thermostat. If I were to do away with it, would I need to make any wiring connections? Is it best to simply leave it where it is and forget about it, since it will no longer have a WR1 to talk to? Lastly, would I still need the small grey gadget (again, a British Gas-branded thing) that's connected directly by an Ethernet cable to my broadband router?
@norman75278 ай бұрын
Thanks Mark. It does sound like a very poor device to me. Please advise on a good quality device with timer and external sensor
@MarkBallardLTD8 ай бұрын
This is a real problem I have been having. All manufactures are changing to smart controls which all have good and bad point and in general are more complicated. I find a lot of people don't want smart. They just want simple. Which I am totally on board with. I am trying to find a simple control which believe it or not this is simple control.
@MarkBallardLTD8 ай бұрын
I am trying out the new Drayton Digistat RF901, Video to come. But that has some not intuitive setting for manual operation, which is very frustrating. Honeywell T3R has become very unreliable which is also frustrating.
@Brando16678 ай бұрын
Very informative and well explained. However, I can’t stop thinking you look like one of those prisoners in the US 🇺🇸 that wear the orange boiler suit and chains. You ain’t got your ankles chained together under the table have you?! 😛
@daver32506 ай бұрын
Hi Mark, We're moving house and leaving all of our hive stuff behind. Do you know how to reset it all so the new owner can use it and it's totally from our email address etc please?
@antoniogalluccio42136 ай бұрын
The only way to change the schedule without using the app is to actually by the the hive with hub. Told by Hive over the phone
@gamereva64138 ай бұрын
Great video as usual. Do you still need a live, neutral, and earth to the boiler, to power the boiler. Thanks.
@MarkBallardLTD8 ай бұрын
Yes you do
@philipdavis95798 ай бұрын
Can you use these to replace an old Honeywell thermostat?
@MarkBallardLTD7 ай бұрын
yes and no. If you want to remove an old thermostat off the wall and replace it with this in the same place, then NO. If you want to remove an old thermostat off the wall and find the wiring centre and wire the receiver unit in there, then Yes. Watch my other video How to Install Hive Thermostat Mini on a Traditional system. Coming Soon.
@philbrown224 ай бұрын
The advice I had for years the hive is not clear
@jaywonder70997 ай бұрын
Hi my receiver doesn’t power on I replaced the old receiver. I only have two wires the negative and live wire. I have no light on the receiver.
@simon87617 ай бұрын
You need 5 wires Live Neutral Earth Heating on heating off