How to Repair Alternator VALEO Volkswagen Seat Skoda Audi

[@ItchyKneeSon]

Awesome! Thanks for the video! Let's hope the YT doesn't start taking down videos for playing europop in the background and this knowledge is lost forever.

[@Seboja]

I hope they understand that it is

[@will_doherty]

Excellent video - thanks for sharing your expertise.

[@josefranciscoquevedo646]

Exelente Trabajo !!!!

[@technocris1]

thank you mate, you are professional !

[@mustapharouane-l4r]

You provide great content, thanks

[@fedor1537]

Мира и процветания. Было тревожно за обмотки, когда ты зачищал корпус.) Спасибо за видео На твой взгляд, генераторы каких производителей переоценены, и наоборот?

[@adanlara3713]

Que buen trabajo. 😮. felicidades

[@uniquebarberstattoo2841]

Thank you for the video what cleaning sparky are you using if you don’t mind me asking , thanks

[@uniquebarberstattoo2841]

Spray I meant !

[@petroschristodoulides6116]

Best video ever seen. Thank you for your explicit demonstrations. Where do you find the replacement parts? Where I live they only have regulators. I only need brushes and brush collector. (Valeo alternator)

[@Seboja]

Hello and I'm glad you like my video. Contact me by email, I have all the necessary parts you need.

[@Amurphybartlett]

I looked at and called every auto parts store in my area... none had brushes, but suprisingly Ace Hardware had a pretty wide selection of brushes

[@Biggie_Johns_Son-v3i]

Nice job!

[@wsnxumalo6707]

Good job

[@Seboja]

tnx :D

[@dino5002]

Thanks for your effort a great teardown. If a load was applied to this for a long time (eg an hour) could it continue to produce 140ah or does the regulator start to limit current due to heat?

[@JohannesC-c9k]

Excellent work, what kind of epoxy did you use, JB Weld? Can it be assembled without it? Why cut brushes in the lathe?

[@WiekingderViking]

I think that the lathe was used because the slip rings were not exactly concentric with the rotor shaft. After the lathe work, the brushes won’t bounce/skip on the slip rings! Bouncing would cause arc’ing which would cause (1) poor voltage output AND ((2) premature wear of the brushes and slip rings.

[@naseembeg5396]

Nice video

[@Seboja]

tnx :D

[@michel5613]

What solderingiron do you use for this job? My 200 watt was struggling to get the job done.

[@miloscerovic2055]

Majstore, možeš li mi tačno reći koju lemilicu koristiš i koji model? Gde si je kupio? Pratim te duže vreme, odličan si! Pozdrav! 😁

[@Seboja]

Pozdrav rucna izrada kontaktiraj me na fb ili insta pa cu ti dati informacije

[@Alexandre-iq8lp]

🇵🇹🇫🇷impec bon boulot 👍

[@abdfakhour7561]

hello, Your video is very interesting but the problem is that the image of your camera is blurry and you do not say which product you used to wash the alternator

[@Seboja]

Hello, thanks for pointing out the sim problem, I know that I have a problem, I am recording with my mobile phone, I hope that in the future there will be better recordings. I wash the parts with engine cleaner (K2 AKRA)

[@sinancan9520]

good job

[@Seboja]

Tnx :)

[@ricardojuarez291]

It looks like you are an expert repairing alternators, I have a few questions about alternators.. I need a high output alternator, toons of amps like 300 amps +.. and 15 volts how can you get that out of an alternator?

[@Seboja]

Only to buy another alternator! and other components. look under this number on google 8600628 and 11075N-300A you can visit the page as-pl and see exactly what you need!

[@ricardojuarez291]

@@Seboja thank you for taking the time to reply to me, I do really appreciate it but, I tell you my story I brought an alternator from eBay, and supposed to be 250 amps and I don't think it's 250 it looks exactly the same as the original so, I feel I got scammed..,, internally are different?? And I saw a different companies making those high output alternators and it looks bigger and stronger.. so I'm confused,, so that one you send me 11075 it's 100% high output alternator?? Thanks again

[@Seboja]

@@ricardojuarez291 See this alternator he is exactly 320 amp 8600634 there are also smaller alternators of 250amp from Mercedes but they have computer communication

[@Seboja]

@@ricardojuarez291 as-pl.com/sr/main

[@ricardojuarez291]

@@Seboja Thank you I been doing a lot of research and I found couple companies here in USA, mechman alternator, stinger alternators and some others... They are expensive but I need one of those to run a 8 k watts sound system.. thanks for your help you earn a sub.. I'll make sure leave likes and comments.. keep up the good work..

[@csongorbalazs7404]

Good job!

[@TheFoxho]

My car battery voltage does down to 12.8V when the AC and lights are turned on. When i turn off the AC... it goes to 13.5V. Is this a sign of a bad alternator?

[@SpikesMavic]

Excellent vid tanks you, but I wish you would use some dissposable gloves when working with all that crap on them !.

[@masoudnikfar3766]

Very nice job man you are a pro. I just wanet to know the kind of spray you applied to bearing before pulling it out and second the material you applied with with brush before soldering the two brushes wires in their holes. THANKS

[@boombook6508]

Spray is wd-40 penetration oil. Not sure about material he applied with brush, some sort of soldering flux

[@matejpupex9749]

what type and marking does this valeo alternator have? thank you very much

[@medranolopez3853]

What liquid do you use to clean it ?

[@marius4668]

Hello. Can you tell me please from what piece could be the sound like rubbing stones?

[@Seboja]

May be 1: Bad bearings 2: The rotor will touch the stator

[@marius4668]

If rotor is touching the stator could be seen from outside with engine on?

[@tiago39283]

Hello , very nice work , wath kind of glue /paste can be used ?

[@Seboja]

tnx :D Name of paste Felder 250g metal content at least 60%

[@mihalym.6876]

@@Seboja Hi, what type of two component epoxy glue can be use to fix the wires?

[@Seboja]

@@mihalym.6876 Wurth liquid metal

[@doudoumohamed7885]

👍👍

[@1.9tdilove71]

I just my skoda Octavia mk1 1.9 tdi alternator repaired. Two coils got shorted. Now working fine. But is repair successful in long term?

[@Seboja]

Was your stator shorted? burnt coils or what?

[@1.9tdilove71]

@@Seboja yes, startor motor was burnt and ignition switch was also not returning. So first starter and ignition switch was replaced then battery then repaired alternator.

[@1.9tdilove71]

@@Seboja now I am getting running voltage around 13-14 . Is it ok?

[@Seboja]

@@1.9tdilove71 13,7 - 14,2

[@1.9tdilove71]

@@Seboja Thank you for your expert advice my dear friend .

[@Дмитрий-с9ш6б]

26:35 please tell me the number of this ring

[@radanmilakovic2913]

Kolega gdje se moze nabaviti taj radapcige.

[@Seboja]

Force ga prodaje

[@WiekingderViking]

Unsolder those brush leads!!!!!!!

[@zekass1986]

Alternator clutch pulley you turn on with air tool,are you sirius?😀

[@Seboja]

Hello, I always finish the pulley with the gun and I never have a problem with that

[@Starter0831]

Could tell me the bearing numbers?

[@Seboja]

Bearing 17x47x14 (number 6303) and Bearing 15x35x11 6202 (number 6202) Cargo Number

[@Starter0831]

@@Seboja thanks so much

[@Seboja]

@@Starter0831 and another time: D I'm here to help

[@muradshaikh1587]

Dear soldran iron why oarches

[@milidragvukovic4047]

Гдје се може набавити овај радапцигер

[@Seboja]

Force

[@silasatlas3835]

niether you or the alternator say much!

[@ascenchon]

Too much time por cleaning…

[@abdfakhour7561]

hello, Your video is very interesting but the problem is that the image of your camera is blurry and you do not say which product you used to wash the alternator

[@Seboja]

Hello, thanks for pointing out the sim problem, I know that I have a problem, I am recording with my mobile phone, I hope that in the future there will be better recordings. I wash the parts with engine cleaner (K2 AKRA)

[@domingocorona3559]

I was just about to ask what the spray was until I saw your comment, still best videos on Bosch alternators I’ve seen on KZbin

[@WiekingderViking]

He may turn the new slip ring assembly in the lathe to make SURE that it is absolutely concentric with the shaft! Otherwise the brushes will “hop” at high rpm’s -- poor contact will affect output and cause unnecessary arcing on the slip rings which is BAD!!!! IMHO.

[@WiekingderViking]

BTW, This is a great example of mfgrs now making us NOT be able to repair our own alternators. -- thin copper slip rings and all potted in epoxy. I have no idea where he was able to get new slip ring assembly…. Don’t know how he can make any money doing all this work, which I highly commend him for doing!!! RIGHT TO REPAIR!!!