How to Replace Headlight 10-15 GMC Terrain

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@CeaseNY]

I got tired of shops giving me the runaround to change my assemblies, i watched this video a few times in a row and went and changed them both myself in 30 minutes. (2011 slt-2) Thank you so much!!!

[@1AAuto]

+@CeaseNY Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

[@suemccabe7496]

Thank you! They wanted $600 to replace the headlight housing I saved almost 500 My daughter and I were able to do it in 40 min. Thanks for being clear and keeping it simple! not adding complicated stuff we didnt need

[@1AAuto]

+Sue McCabe Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

[@charibortner3737]

i watched the video on replacing 2014 GMC headlight assembly. The video was absolutely fabulous, step by step, easy to understand and gave you the required tools needed. Mind you, I never tackled a car repair myself but after watching the video, I decided to order the part from 1A Auto and do the installation myself. The part came in 3 days and it took me about 1/2 hour to replace the headlight assembly and it is working beautifully. Thank you for the video and I will totally recommend you to my friends and family.

[@tjmicsak]

For a 2014 Terrain that has no wheel well access- passenger side all done under the hood 1. Remove the 4 plastic pins that hold the inner trim along the fender/hood from front to back by popping the center up of the expansion pins with a flat blade, then pry the base of the pins out. There are three in front near headlamp and one at the rear end by firewall. 2. Unhook the rear hood rubber gasket strip by pulling it and unhooking it from the tab on the trim back end. Now lift the side fender top trim and pull out from back (it has a built in hinge point) , releasing the two metal clips along the fender top and then back it out of the front inset plastic tab over the radiator. The trim side is now free and can be set aside. 3. Remove the two screws holding the small cross side "T" bracket and the one smaller screw that fastens the headlight top back to that same small cross "T" piece. Lift that cross piece out so the metal formed insert tab on it comes out. 4. You now should have just enough hand access to reach down behind the headlamp to twist off the circular cap seals, and then access to the bulbs inside them. The rest of the replacement is the same as if you had a removable fender access to the bulb back circular caps.

[@rickeylambert6445]

This goes for the 2016 as well. No wheel well access. All under the hood.

[@faychin1104]

Great video, replaced both assemblies in 90 minutes on a 2013 Terrain Denali and your instructions were perfect. Only suggestion is that the corner clip at the edge of plastic bumper is located at the corner so a pry bar used at the edge is effective in popping off the plastic bumper.

[@oliviasumlin]

Just saved $80 with this video. Mechanic wanted to do it hard way and take off panel and charge by the hour saying it would take half hour. Thanks for posting

[@1AAuto]

+oliviasumlin Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/1A/HeadLights/GMC/Terrain/1ALHL02140?KZbin&CTA+Comment&ZMaolGYlWYM

[@lldvpeandrewll8616]

Same

[@wesleymontgomery5301]

I miss when headlights didn’t require you doing anything but removing the headlight. Now you gotta take off bumpers

[@jertexjertex7880]

This does not work for the 2015 Terrain, GMC, in their amazing wisdom, eliminated the round, removable cover in the wheel well and now you have to take the entire wheel well cover off to get to the bulbs. Edit: well, not quite remove it, but you have to turn the wheel in toward the body and remove 3 torx screws and a pop rivet and then force the wheel well cover back far enough that you can get at least one hand in to remove the cap and then remove the bulb. You have to wear some kind of glove when installing the new bulb because you don't want to get skin oil on a halogen bulb, otherwise the heat will be drawn to the skin oil and melt the glass and ruin the bulb. I could only get one hand in, but I was able to change the bulb with just one hand.

[@onionjohn1]

You guys saved me $$$ and time. Consider me a new brand loyal customer.

[@1AAuto]

+John Smiley Thank you for your order. If you would like to leave us a review on Google it would be greatly appreciated. Here is a link to our reviews section. Have a great day! goo.gl/i5JFNY

[@Azadum]

Thanks for showing putting it back together after the bulb is in. That's where I got messed up. I had the plate you twist pointed in the wrong direction and couldn't figure out why it was so hard to get on when it was so easy to take off.

[@vellvirginia2218]

9 year old video saved me a lot of time and frustration

[@Mercileez]

THANK YOU DUDES I thought I was going to have to remove my whole bumper just to get to the housing. Had no clue about the trap door in the fender well

[@JGray-bt1fu]

Thanks! This saves me $60 for about a 10 minute fix.

[@1AAuto]

+J. Gray Thanks for watching 1aauto.com 888-844-3393

[@patrickgraham24]

Thanks for the video! I was able to change out my headlight pretty easily once I got the wheel well cover off. Just have to blindly feel around and know which bulb you need to change.

[@1AAuto]

+Patrick Graham Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@mohoganston]

Really helped me find that bolt hidden by the front panel

[@chadinnocenti4906]

You might want to add the end adjustments so people don't have one head light pointing to left field and another straight to the ground lol

[@tamikab.5868]

Thank you. Replacing my low beam today.

[@toridr4484]

Hello I want to say thank you so much for your video it explained it perfect I was able to complete it and now my lights look good I we'll definitely keep you in mind when I buy car parts

[@izekecantu7656]

This was very helpful able to swap bulbs in less than an hr

[@derricklongstreet7849]

Thanks guys😁👍

[@crzycop]

I have a 2015 and the access panel you show in the wheel well area does not exist You will have to remove three of the clips 2 T15 screws Lastly two 7 mm bolts underneath the front spoiler Where the wheel well connects to it You can then gently pry back be wheel well to access the door panel to the headlight bulbs When removing the screws from the wheel well keep the wheels turned inward then When you are prying back the wheel well slightly to gain access to the headlight assembly you will want the wheel turned out

[@ffighter6932]

My 2014 Terrain SLT only has the fiber wheel well liner with no little door. You have to change to bulbs from the top.

[@kristinazalzal]

Great video! I changed my headlight bulb myself! Thanks! :)

[@1AAuto]

+Kristina Zalzal Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@matthewstaton9197]

Thank you! Worked on my 2013 Terrain. Replaced the low beam.

[@1AAuto]

+Matthew Staton Thank you!

[@FSmithSE1]

EXCELLENT BULB REPLACEMENT VIDEO

[@1AAuto]

+SPARTAN SMITH Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@williamtruong4119]

I am trying to remove the headlight cover, the one right in front of the access hole, but it isn't coming off when I turn it counterclockwise. It looks like the long tab is missing from mine. Any advice on removal of the cover?

[@willyquiles8421]

Very helpful thanks

[@caseymiller846]

We’re that second bracket goes into the headlight with the 10 mil bolt my headlight is broken we’re that bolt has to go in will the bumper still snap on securely without that bolt in the headlight. I’m trying to figure out if I’m gonna need a new headlight before I get to it because right now Im working on putting the fender back on and maching it into place along with getting all the pieces back on the bumper!

[@r.powerborn8026]

Excellent video! Took 5 minutes to change the bulb through the wheel well access point. Would have been faster if it wasn't 16° outside. 🤣🤣🤣 Thanks Bro!

[@frenchispluss4976]

Thank you for your help.

[@charleskincaid5718]

Thanks for the video

[@boomertsm]

Most techs say not to touch the actual bulb with fingers (oil) to prolong life of the bulbs..

[@1AAuto]

+Terry Moore True. The oils on the bulbs themselves can make them burn out prematurely.

[@samzaa5069]

Thank you so much

[@jeanannthompson7960]

Know where I can order more of those clips from inside the wheel wells? Thanks for the video, upgrading my bulbs!

[@1AAuto]

You may be able to get new ones from you local auto parts store or from the dealer. Hope this helps you out. 1aauto.com 866-403-3393

[@sessypinkmama]

Do I need to take the whole headlight off to change the bulbs?

[@1AAuto]

+Kendra Jackson You may be able to reach around the back of the headlight to remove them.

[@vnappen]

How do I adjust the height of the lights my car was in an accident they were replaced but they are aiming too low. 2014 SLT Terrain

[@Don_ECHOguy]

There is no headlight adjustment... so if your headlights are aiming low the headlight mounting points are out of wack.

[@johnmays7651]

Thanks for the info. Saved me money and time. Would have to have had mechanic do it since I got ot due to health reasons years ago but could do this. Thanks again

[@1AAuto]

Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com +john mays

[@nickr3441]

I dont understand how you are suposto change the headlamp by just removing the cupbord behind the wheel. You are basically working blind, bc you can only fit your arm in there. If you can shed more light on it it would be greatly appreciated

[@1AAuto]

You can access just the bulbs by removing that access panel that we show. They should be right in front of you once you take the cover off.

[@NPAMike]

Turn the wheel to have better access.

[@dustystix76]

My 15 doesn’t have that wheel well access on either side

[@dawncarman1481]

So I replaced my headlight assembly. But I dont know how to adjust the bulbs. Apparently I need to adjust the one side and do not know how.

[@AlfredoCosta77]

Can I buy only the front clear plastic to my headlight?

[@KorbenDallas]

Cannot remove any such quick access cover from a 2014

[@101xotic]

curious 2015 headlight fit on a 2016???

[@Broncomaniac-15]

great vid

[@dalast1woke]

hey this is not the same for the 2015 terrain or newer. is there a new video coming for those models?

[@1AAuto]

+Brandon Floyd Thank you for watching. Unfortunately, we do not have a video for your application. We will keep this in mind for future repairs. www.1AAuto.com?KZbin&CTA%20Comment& 866-403-3393

[@lycanwarlord]

Thank you

[@DanLoFat]

Is it me or is it the method for changing the lights the same as removing the whole light assembly? Do I miss something there?

[@1AAuto]

+Dan Lo Fat Thanks for checking us out! You can change the bulbs without removing the assembly however for the purposes of the video, we show how to replace the bulbs on an assembly that was removed. You do not need to remove the assembly to just replace the bulbs.

[@wendelllynch120]

I don't see any cap in the wheel well of my 2015 terrain sle-2. Is there any other way?

[@1AAuto]

+Wendell Lynch I would pop the hood and see if you can reach in there to access the back of the headlight. If not then you will probably have to remove the wheel wheel cover itself. 1aauto.com

[@wendelllynch120]

@@1AAuto I noticed that I have to go from the top under the hood. You should do a video on that type🤔

[@ohiotim7742]

The later models do not have the access port in the wheel well. You need to remove the headlight assembly as the video shows for “replacing” the entire assembly. Once you have it pulled out, you just replace the bulbs and reinstall it. Way too much effort for routine maintenance; gross oversight by GM or a new way to force many people into the shop for what should be a simple DIY fix.

[@dirxwirx]

Yeah, the one they show in the video is the easier method. The model you have requires you to go from the top under the hood. It's extra hassle and time unfortunately.

[@travisjames1263]

thank you!

[@1AAuto]

+Travis James Thanks for checking us out! 1AAuto.com

[@RobRestoredMorgan]

What a Pain in the Butt!!

[@1AAuto]

Hopefully this video will help out. If any of our viewers needs to replace their headlights, we carry the headlight kit shown in this video on our website. Here's a link to them goo.gl/RK0pHn

[@RoseGold823]

Try doing it on a Ford escape. This is gravy

[@jpontiac4294]

Nice

[@TonyMontana-ew4xd]

thanks for the help

[@bethvickers6560]

Mine doesn’t have the little trap door I have a 14 terrain we have to take the front off

[@7777777Beau7777777]

Is it the same on 2016s or different?

[@1AAuto]

+Beau Man At this moment, the closest how-to video we have to your request is for this vehicle, which is very similar to the one you have. The steps may not be 100% the same, but should contain an adequate amount of information necessary for accomplishing this task. Thanks for checking us out. 1aauto.com

[@jeffs4904]

How does one go about changing the fog light bulb?

[@1AAuto]

+Jeff Sinclair You should be able to reach behind the fog light assembly and remove the bulb. You may have to twist the bulb in order to pull it out. If you need to remove the entire assembly to gain access to it, this video will show you how to remove the fog light assembly. Hope this helps you out kzbin.info/www/bejne/aaK1dImYZ9F6jNU

[@beckytrotti7963]

is this the same for 2010 model GMC terrain?

[@crlaw75]

Should be. Model years '15 and up have a different fender liner, which do not have the cap to unscrew.

[@JRGoehring23]

I have a '14 that has the fender liner with no cap. It's much more of a pain. And yes, it's a '14. Guess I'm just lucky...

[@naviambigram]

Thanks!!

[@alexwhateva]

Can you guys make a video of how to remove headlights on a Chevy Equinox 2010 please

[@geraldwayne6261]

It is the same as Terrain! One is Chevy, the other is GMC! Same vehicle though!

[@dsmartinez6096]

You forgot to show how the whole assembly comes out

[@meanman61]

Can’t find any video on how to change an Alternator/Belt on a 2013 GMC Terrain SLE. Not even a video on whether it can be done from the top or bottom?

[@blakemartinez9315]

Can you just replace the lens? Mine is all faded...

[@racerx6284]

Yup. I just bought a pair and am going to replace the whole "pod assembly" on my 2010 Terrain this weekend. Didn't you watch the video?

[@dexterstanley4185]

Just restore it instead of replacing. Much easier and turns out bend new

[@chrisrehkop7797]

Not all terrains have the dust covers

[@1AAuto]

+Chris Rehkop Thanks for the feedback!

[@VegasTales]

The 2014 doesn't have those covers

[@arcticwolf8150]

Too bad the SLT version doesn’t have that round access for the bulbs you have to take the wheel hull plastic flap out of the way to get to them

[@uhsenli6424]

Why does the guy feel like he’s about to pass out changing a bulb

[@marksmopar609]

I was hoping there was a adjustment that could be made but I guess not.

[@1AAuto]

+marks mopar Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@ronholder4373]

This is not true I have a 15 terrian and those covers are not inside the wheel well!

[@Timmhudd55]

My brand new light fixture has water inside. Thanks

[@Don_ECHOguy]

Don't use cheap reproduction parts if you can help it.

[@lionelthompson9916]

You didn't show enough information how to take it out

[@Rubenowski]

NEVER TOUCH THE LIGHT BULBS WITH HANDS THE OILS FROM YOUR SKIN WILL CAUSE THE BULB TO GO OUT PREMATURELY.

[@1AAuto]

+Ruben Rivera Thanks for the feedback!

[@jeseniacortez2869]

no tanks

[@whitebread1011]

That's ridiculous

[@smithrock9311]

Ppl 9a

[@holmes1956O]

Worst how to I have seen you guys do how about changing the bulb with the nacelle in the car. Whole different ball game

[@1AAuto]

+holmes1956O Thanks for the feedback!

[@mikeschneider9462]

Well I already hate this car.

[@neillameier8644]

Gmc engineering is so bad👎

[@FSmithSE1]

EXCELLENT BULB REPLACEMENT VIDEO

[@1AAuto]

+SPARTAN SMITH Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@raqueelking]

Thank You

[@codyrace4595]

How do you adjust the beams