How To Replace Vapor Canister Purge Solenoid Valve 2006-12 Ford Fusion

Buy Now!
New Vapor Canister Purge Solenoid Valve from 1AAuto.com 1aau.to/ia/DMEEV00011
Vapor canister purge solenoid valves are an important part of the EVAP system that allow the contained fuel vapors to be released into the combustion chamber under certain conditions. Modern purge valves are controlled by the vehicle’s computer system, and electronic solenoids. Failure of the valve or the control solenoid will result in an emissions trouble code that could prevent passing emissions testing. This video shows you how to install a new vapor canister purge solenoid valve on your 2006-12 Ford Fusion.
• Check here for more videos on the 2006-2012 Ford Fusion: • Ford Fusion 2006-2012 ...
This process should be similar on the following vehicles:
2006 Ford Fusion
2007 Ford Fusion
2008 Ford Fusion
2009 Ford Fusion
2010 Ford Fusion
2011 Ford Fusion
2012 Ford Fusion
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXAA00013
• Straight Cutters
• Floor Jack 1aau.to/oa/1AXAA00068
• Jack Stands 1aau.to/oa/1AXAA00065
• Pick 1aau.to/oa/1AXAA00037
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Ford Fusion 2006-2012 1st Generation: • Ford Fusion 2006-2012 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@ghettohey2388]

So my 2001 ford f250 fuel vapor tube assembly needs replaced. I cant find the OE replacement so will it matter if I replace the tube assembly with a smaller diameter tube. The original is 1/2 O.D. and the replacement would be 3/8 O.D

[@2paulm]

This is not a "Purge Solenoid" it's a "Canister Vent Solenoid" the purge solenoid is always in the engine bay

[@aaronsumano2994]

Great video very clear ! Can be p0442 code caused for this valve ? How do I check it is working? ….thank you TRQ!

[@haxino]

Great video 👍

[@joshuag8988]

Is car the 4 cyl. or 6 cyl. model? Is the purge valve in the same location on both? Please specify.

[@austintorvund1]

I am about to replace my fuel pump. No codes just wrench light. Constant fuel pump pumping when running random fast pumps. Could it be this canister causing fuel pump to pump gas?

[@rabiaasad5553]

what are the symptoms to make it safe for all the parts? every time new parts light comes to the desk light.. after I replaced then again new light has come. so what is the solution to make it cure.

[@alexissabbagh4049]

If i replace the charcoal canister will i still need to replace this part in the video? Is it connected to the charcoal canister?

[@amaldonado956ify]

could a bad canister cause gas to come back up at gas pump?

[@Arnseto88]

That’s the purge valve canister, we’re is the purge valve location?? I can’t find the diagram anywhere???

[@gustavocampos4395]

I replace this part on my 2008 fusion v6. Does the check engine light erases by itself or I need to delete it from my dashboard.

[@TRQ]

+@gustavocampos4395 The engine light should be cleared after the new part is installed.

[@nickboyes6536]

How do I diagnose that this valve has failed?

[@isaacchavez1062]

The engineer light will tell you

[@appelsinnadurai]

This person is misleading the people. He is not replacing a Purge Valve.