How to take a part an "Oster Fast Feed" by: JOE FADE

In this video, I'll be taking apart an OSTER FAST FEED. Also, I'll show you how to ZERO GAP your clipper.
FACEBOOK: Joe Fade
INSTAGRAM: joefade_mlb
STYLESEAT: Joe Fade
Beats I Used out in the link below:
piff.me/4098359
Thanks again, GOD bless!!

[@DepartmentOfJustice]

Thank you so much for this. I could not for the life of me figure out where that little copper piece went. I'm not sure how taking the clippers apart and putting them back together fixed the problem, but they're working again, so thanks for saving me $70 on a new set!

[@BobHamiltonRWH]

I just bought a used one of these. It hasn't been used much. The blades were loose, the black holder wasn't in place and the copper thing was off. Luckily, they were all there and I got it all back together. My wife cut my hair and loved the new machine. After watching this, I'm going to go take it all apart again. Now, I know where the copper thing goes. Thanks for the video!!

[@JeffinTD]

Super helpful video. Thanks for taking the time.

[@dree2373]

Thank you so much for this easy to follow vid. Really helped me.

[@nancybloore918]

Best video I have ever seen cleaning a clipper! What can I use in place of the original sponge?

[@esuohelyk]

Thanks man, great video!

[@ziggypowers1644]

OMG, ty!! I'm repairing mine because I was stupid and lent them out during the early months of covid and the POS broke the exterior metal blade. Problem was where the fuck does the stupid copper piece go!! Sub and a like, Thanks for the thorough walk through.

[@paulmaloney2383]

I have no problem taking things apart , putting things back together is the problem

[@nelq415]

thanks for the vid

[@micheleiams4]

Great video! I am waiting for my gray bar to get in however is there anything I can do to Linda makeshift it until it gets here?

[@josephalejos5443]

If you have any detachable blades for a 76er that are laying around you can take one off of there and use it. It might got fit properly but itll work for time being

[@acordova8014]

Well done,thanx.whats your thought on ceramic blade for the fast feed? To zero blade

[@josephalejos5443]

I haven't tried them bit I hear they're good they don't heat up

[@foodiequeen116]

Where can I purchase the sponge inside???? (Hair guard sponge) very helpful video thanks

[@josephalejos5443]

hobby lobby sells it or any craft store near you should sell

[@kriticol3052]

everytime i put the lever open and close, it doesn’t look straight or aligned whenever i play with the lever, it looks like it’s not aligned or something . is there a way to fix this?

[@marlostanfield1946]

The background music👎🏾

[@rottiejakeluke]

Do you have this type of video for the Oster 76?

[@josephalejos5443]

No I sure dont but give me time and I can make one 👌🏽

[@alexanderreyes3356]

Broo can you help me out here I assembled everything back together and even lubed them like you did here, but now my fast feeds are louder than before.

[@josephalejos5443]

Check to see if the rubber mod is on the bar where the top teeth rest on is attached

[@thespoho32]

Nice vid bro. I have a question though, my fast feeds make a whistle noise when the lever is all the way closed few seconds after turning them on. Think you know of a fix?

[@josephalejos5443]

thespoho32 have you oiled the blades?

[@thespoho32]

It got fixed I just needed to oil the inside of both blades I guess I didn't put enough the first time. Thanks for the help!

[@josephalejos5443]

thespoho32 no problem glad I could help

[@ExtremeKBdotCom]

where do u get that grey bar if its damaged or lost?

[@josephalejos5443]

Heres a link I found. I've never used this website bit it's worth a shot. www.ereplacementparts.com/blade-guide-p-649229.html?gclid=CjwKCAiA9JbwBRAAEiwAnWa4Q2Bl7nBU9tcYgwSEDmMx_ppgmiZqV1CQ0nP5jdpXRPeCetjKorkbhhoCYpQQAvD_BwE

[@huskygunslinger5636]

Is there any way to remove the metal pole that the pivot wraps around? I’m trying to convert to a cordless and the pole is just in the way.

[@josephalejos5443]

You can remove the pivot pole with square plyers and move it in a twisting motion and pull at the same time it'll take a bit of force but its doable

[@huskygunslinger5636]

@@josephalejos5443 thank you! I wasn’t sure if it was possible.

[@luvyatubers]

I'm here for the part he forgot. The sponge. But all the rest helped greatly. Thumbs up

[@andrewheale9170]

My fast feeds straight up don't cut.. I even bought a ceramic blade and zero gapped them but they still didn't cut. They just pull hair. I'm wondering if I got a lemon...

[@blkschizo]

check to see if you lost that grey bar. I didnt realize that was the problem withmine for so long. I have 2 sets of Fast feeds and neither had that part. This fixed it right up.

[@blkschizo]

www.ereplacementparts.com/blade-guide-p-649229.html?gclid=CjwKCAiA9JbwBRAAEiwAnWa4Q2Bl7nBU9tcYgwSEDmMx_ppgmiZqV1CQ0nP5jdpXRPeCetjKorkbhhoCYpQQAvD_BwE

[@leoparra898]

does the blade get loose after cutting hair ?

[@josephalejos5443]

Leo Parra it's not supposed to

[@juanperegrina6236]

Is the foam piece necessary ?

[@josephalejos5443]

Juan Peregrina it helps to keep hair from getting inside the clippers.

[@mikespeer8852]

A little gray bar came out mine when I took the blade off where does it go

[@andrewheale9170]

Did you figure it out cause that messed up my cuts till I put it back where it belongs

[@mikespeer8852]

@@andrewheale9170 I think I did not %100

[@user-gp6um1nb1g]

супер обзор

[@sushanawatson932]

Whats the name of the foam piece when i go to hobbly lobby ?

[@josephalejos5443]

Look by the paint section it should be around there

[@allamark3]

@@josephalejos5443 ok thank you

[@allamark3]

@@josephalejos5443 so you just looking for a grey sponge in the paint section what do hobby lobby call them at the store i wanted to buy online if you could send the link that would be even better

[@josephalejos5443]

@@allamark3 www.hobbylobby.com/Crafts-Hobbies/Basic-Crafts/Craft-Foam/Metallic-Glitter-Foam-Sheets---9-x-12/p/80764375

[@josephalejos5443]

@@allamark3 online this is what I found

[@AztecBrown]

where can I get the foam

[@josephalejos5443]

You can go to a arts and craft store

[@AztecBrown]

Joseph Alejos thanks 🙏 bro

[@AztecBrown]

Joseph Alejos I need help you can show me How fix persistent loose levers 😭

[@josephalejos5443]

@@AztecBrown it might be the washer in inside the lever might be to flat that its not giving tension, or that the bottom housing might be stripped that it doesn't hold the lever in place. Try to bend the washer a bit to see if that works if not, then you might need to buy a new housing

[@AztecBrown]

Joseph Alejos thanks you bro 🙏

[@lrgmook9920]

What's in the e.p.a??

[@josephalejos5443]

it's barbicide, it's mixture that kills all form of life

[@lrgmook9920]

Joseph Alejos whats the water to barbicide ratio if u dont mind me asking?

[@josephalejos5443]

LRgMoOK 99 you mix Barbicide is mixed correctly by adding 2 oz (1/4 cup) concentrate to 32 oz of cold water. Also, you can mix Barbicide Plus correctly by adding 1 oz (2 Tbsp) of concentrate to 128 oz (1 gallon) of cold water.

[@horse5407]

What is that goddam awful fucking noise?