How to Time a Coyote Engine (Gen 1)

Рет қаралды 17,169

3 жыл бұрын

Subscribe + Share!
Follow Me!!!
Facebook: / connor-guasti-10790612...
Instagram: Coyote_TwinTurbo
lituningandracing.com/
Instagram Lituningandracing
Brazzel Performance Fabrication
252-675-2582
Instagram: JasonBrazzel
blfabrications.com/
Instagram: BLFabrications
billetproshop.com/
Instagram: Billetproshop

Пікірлер: 50

@RayGT-du6hj Жыл бұрын

Just found this channel after searching coyote building videos. I had a Gen5 Whipple installed on my 2014 back in the spring and I want more! I’m putting out 695WHP but I’m chasing 4 digit power now. I have a block ready for parts that I plan on building myself over the next little bit. Going fully forged internals, billet timing set, stage 3 blower cams. I’m really enjoying your videos. Thanks for making them!

@ConnorGuasti Жыл бұрын

I need to make another one soon.

@Marine2111usmc 6 ай бұрын

Nice same here.

@MatthewRicchiuti 2 ай бұрын

Extremely helpful bro. Thank you

@scottybear6265 Жыл бұрын

I’m so glad I found another coyote lover

@rosco664 Жыл бұрын

Very good video. I'm a little old school and know about sbf, sbc, bbc, bbf. Just ole push rod engines, and currently own a 12 Boss 302 and just trying to rap my head around these coyote engines to have a better understanding.

@ConnorGuasti Жыл бұрын

Thanks sir!

@coleworldcustoms6908 2 ай бұрын

Just finished up mine awesome video helped me more than you will know, but my passenger side tensioner (which is new) is hanging it’s not as springy as the driver side. I know they are pressurized by oil so should I replace it? Ir is that normal

@staytuned8761 5 ай бұрын

Well I’m doing timing chain to my 2011 mustang gen 1 coyote and was watching your video I took cams off and have it at 12 o’clock position and installed cams back with the code facing up but this method works just like going 9’oclock for driver side right?

@Simmonsracing187 3 жыл бұрын

Nice video connor, new camera looks great

@ConnorGuasti 3 жыл бұрын

Glad you're a fan! I got a little wider lense to get a little more in the shot

@crazy87lx 3 жыл бұрын

Great video!

@ConnorGuasti 3 жыл бұрын

Thanks man! Appreciate it!

@seanjones1433 3 жыл бұрын

Great video dude

@ConnorGuasti 3 жыл бұрын

Thanks man! Hopefully it's helpful or enjoyable to watch haha

@bigmotoxer 2 ай бұрын

Half the people on KZbin are using the two colored- links on the intake phaser and the single colored-link on the exhaust phaser.

@dannyorihuela9483 Жыл бұрын

Great video

@ConnorGuasti Жыл бұрын

Thanks man!

@scottybear6265 Жыл бұрын

I like the cam also the clear Visio would you help me with twin turbos on my f150

@ConnorGuasti Жыл бұрын

Shoot me a message on ig

@F1perm Жыл бұрын

My cams got 1 dimple on them and the other 1 have 2 dimples?? Wich is wich?? Im lost

@TheHotSauceGT350 Жыл бұрын

I'm getting ready to replace my timing cover and seriously considered changing my chains since I was there

@ConnorGuasti Жыл бұрын

Do it!

@TheHotSauceGT350 Жыл бұрын

@@ConnorGuasti done and done

@freddiew2242 3 жыл бұрын

good video bro

@ConnorGuasti Жыл бұрын

Appreciate it

@Reggiestreet Жыл бұрын

The Coyote has just two types of phasers (intake and exhaust), which interchange from side to side. The exhaust phasers have two sprockets each. Secondary chains have timing links. The double link goes on the intake cam phaser (left). Single links are located at the exhaust cam phaser (right). This applies to both sides. i was watching your video as a guide now im correcting ing to factory instructions. im not smart enoght to know if it would make a differince or not

@ConnorGuasti Жыл бұрын

Just seeing this, after lots of dyno and street pulls over 1200 hp, i can confirm it did not make a difference haha

@johnanderson71 Жыл бұрын

You said don't turn the crancshaft, if the camshafts are not in place, but you turned it anyway?

@ConnorGuasti Жыл бұрын

Are you referring to right when i started? I moved the crank a few degrees gently by hand to get it to 12 o'clock. I mean something more like, "If you're very nervous about damaging something, just don't spin the crank with the cams on and chains off." Im just trying to help empower people, while keeping them out of trouble. But also letting them know..... its not that serious 🤣

@mcdaniel01 Жыл бұрын

Why didnt you roll the crank to the 9:00 position for the right side of engine

@ConnorGuasti Жыл бұрын

I could be mistaken on this, but I think the reason you have to do that is because the valve spring tension will be fighting you as you try to put the primary chain on bank 2. I can assure you that i personally (in my limited experience) haven't hurt a valve or piston surface doing it this way.

@ConnorGuasti Жыл бұрын

You can't see, but off camera im rolling the cams back counter clock wise with a wrench. Once rolled back far enough, i secure the wrench so the cams don't roll back clockwise

@Relaxedraindude 2 жыл бұрын

Why did you stay at 12oclock for both sides instead of doing the driver side at 9oclock and then the pass side at 12oclock just wondering.

@ConnorGuasti 2 жыл бұрын

At the 12 oclock position the pistons are far enough down to not hit either side. I pull the cams around to make up the slack. Different strokes same result lol

@shadjohnsen8143 2 жыл бұрын

@@ConnorGuasti I have a 2011 GT I am trying to time. I had to remove the driver side cylinder head because of the valve problem on cylinder 8. I turned the crank like I wasn’t supposed to (more than once). The pass cylinder head is still installed but the main chain is not on it. Do I just rotate the crank until the crank key-way is at 12:00 and just make sure the timing marks line up?

@ConnorGuasti 2 жыл бұрын

@@shadjohnsen8143 you could remove the cams and position the crank anywhere you want without worry. Once the keyway is at 12 then reinstall the cams

@shadjohnsen8143 2 жыл бұрын

@@ConnorGuasti Does it matter if the #1 cylinder is TDC or not, what about the intake stroke or compression stroke? The passenger side cams/secondary chains are still installed. With the main chains off, could I rotate the key way to 12 and rotate the cams on the passenger side so that the ID pads are at 45 degrees and be ok? And are the ID pads on the driver side to be moved to the flat horizontal position? Thank you for the quick response. I have to finish this thing before the weekend…per my landlord.

@ConnorGuasti Жыл бұрын

@shad johnsen with the keyway at the 12 position cylinders 5,6,1,3 are about an inch below the deck surface. I do not recommend spinning cams with the engine out of time, or chains off. The best thing to do (if you're worried) would be to pull the cam caps off, position the qr codes face up, then put the caps back on. On both the right and left side the qr codes will be facing up.

@staytuned8761 5 ай бұрын

Hey I sent you a DM about the timing chain

@miketaylor8688 Жыл бұрын

So, I recently completed a 3-1-1 build. I originally timed it with the driver side at the 9 o’clock and the passenger side at the 12. It was throwing cam codes. The exhaust on the driver side the was advanced. The exhaust cam on the passenger side was retarded. I installed limiters. Then the both showed advanced. A friend of mine helped me. We put the key way at the 10 o’clock position. (That’s how he always does them). Now it is showing both banks are running rich. Fouled set of plugs about to foul another. Replaced up streamed O2. Boost reference regulator at 55lbs with the vacuum off. Would you have any ideal what would cause this.

@ConnorGuasti 9 ай бұрын

I wonder if you have a stuck injector?

@SpicyGaijin 9 ай бұрын

I'm having the same issue (P0024 exhaust advanced timing bank 2) on my 2013 F150 even after retiming. I found out after doing the retiming that there is a cam oil filter inside the center of the cam for the phasers. I'm hoping this fixes the advanced timing issue. My phasers are not locked out.

@miketaylor8688 8 ай бұрын

@@SpicyGaijin I ended up having to replace my cams and heads to fix my issues.

@malcolmgunnell1082 3 ай бұрын

OK on the timing chain dark colored links that line up on the timing marks, for us first time guys worth saying FACTORY says - as Reggiestreet below states - single link on exhaust etc etc. Other videos state factory settings then you say something else, result waste a lot of time trying to find out who is right and or if it makes a difference, i did not want to mess this vital step up, watched your video first, then folks are telling me no. Did,nt seem like it would make any difference BUT ????

@ConnorGuasti 2 ай бұрын

The meat of it is this. The tooth count on both sprockets is the same... either way you put the dark links, there's the same number of links in between the marked teeth. Therefore, in my opinion, it shouldn't matter. Also my car runs perfectly fine the way I do it in the video. If you are not confident, follow the factory setup guide on that part. Hopefully the rest of the video was helpful.