I Show You Where The Main Jet For Nikki Carburetor Goes Along With A Few Other Tips

[@donaldbarnett8045]

Best video on the internet for these nikki carburetors . You are the only one out of six that I watched that thoroughly explained about the little brass main jet with the tiny "O"ring on one end non of the others explained how it goes in . Great job one hundred thumbs up to you.

[@JOEZEP54]

Donald Barnett, I am glad this was of help .And thank You for watching and taking the time to make such an encouraging comment !! It is really encouraging & appreciated. When you get a chance check out my video playlist for other videos that may be of help & interest to you. Be sure to👍 , share & $ubscribe if your are inclined to do so. Stay well Joe Z

[@keithcamp328]

I agree With Donald. Mine fell off and I thought I but it back on right but it didn't run long. This clearly shows how it goes and shows I didn't have it on the right side of the plastic pipe. Thanks so much

[@Bolero4me]

Thank you. This is exactly what I needed.

[@philliphall5198]

Thank You for information and advice

[@JOEZEP54]

Always welcome. I am glad this was of help. And thank you for watching and taking the time to comment. Phillip Hall I have other videos on my channel that cover different subjects and new videos added weekly that may also be of help or interest. Your support is not required but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and sharing this content do help. Another way to Help Support The Joe Z Channel at no cost to you is by using my affiliate links or just go to: www.amazon.com/shop/joez An affiliate advertising program is designed to provide a means for sites to earn advertising fees by advertising and linking to amazon, that helps me to continue producing videos. Thank you for your support and using the links provided to make your purchases. This is always appreciated. I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@JimHenderson19]

Yes. Clearly the best video online for this carbeurator. That little brass jet fell out before I could see where and how to put it back. Thanks so much for showing this. Easy to follow and makes sense even to a 'weekender' mechanic like me! I couldn't have put this back together without the video.

[@JOEZEP54]

You're welcome! And thank you for taking the time to make such a complimentary comment. Stay well, Joe Z

[@thefinalgamer2514]

Seriously you are the man! I have been struggling with that jet for 2 weeks.

[@JOEZEP54]

Thank you, I glad this was of help. . @thefinalgamer2514 I have other videos on my channel that cover different subjects and new videos added weekly that may also be of help or interest. Your support is not required but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and sharing this content would help me to reach other viewers that may also find this channel useful or entertaining. Stay safe, Joe Z

[@maryloulou370]

Great job! This is the only video I found that showed me the correct position of that tiny jet. Thank you!

[@JOEZEP54]

Marylou Lou, You're welcome, I am glad this was of help. And thank you for watching and taking the time to comment. Marylou Lou I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Your support is not required or expected but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and using the following links do help. You can Help Support The Joe Z Channel at no cost to you by following my affiliate links. Joe Z is a participant in the Amazon Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon, that helps me to continue producing videos. Thank you for your support and using the links provided to make your purchases. This is always appreciated. ******* Thank you for your support ******** Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@bryanmccollum666]

THANK YOU!!!!!! I looked forever trying to figure out where that little jet went. Good job, thanks for the video.

[@bryanmccollum666]

Will subscribe👍

[@JOEZEP54]

Much appreciated!!! Stay well, Joe Z

[@JOEZEP54]

You're welcome. Glad I could help. Thank you for your support! Stay well, Joe Z

[@BangBang-hk4rg]

You saved my butt Joe! I was taking the carb apart, that main jet fell out and I had no clue where it went back in!

[@JOEZEP54]

Bang Bang, I am glad this was of help .And thank You for watching and taking the time to comment. Bang Bang I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Stay safe, Joe Z.

[@ericwilliams3134]

LOL YEAH SAME THING HAPPENED WITH ME TOO.

[@MisterGhosh]

I really appreciate your attention to problems complete newbies might run into. Your instructions are very accessible, I appreciate your effort

[@JOEZEP54]

Thank you for this comment. I do appreciate you saying so and I am glad it was of help. Stay safe, Joe Z

[@googleuser2452]

Oh my God, that little jet nozzle piece fell out and I was not sure from where, and I found this video. God bless you and your children's children for showing me where it went and how to orientate it. You saved me a lot of pain.

[@JOEZEP54]

You're welcome!!! Thank you for not only commenting but with a Blessing. Google user, your commenting, ...👍s and subscribing if you are inclined to do so are a big help for me with this channel. Thanks again and stay well, Joe Z

[@williammartin4648]

You're the man nobody else would show that. They all had cookie cutter diagrams that show the arrow that doesn't show which direction or where it actually goes. Thanks for a video that actually shows real-time solutions and answers. I watch several videos from major companies wanting to sell a product but none of them actually had the information that you provided. The major companies had it down pat for you to order stuff though. Thanks!

[@JOEZEP54]

William Martin, You're welcome, I am glad this was of help .And thank You for watching and your comment. I do appreciate it. William Martin I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. If you'd like to help 👍, share & subscribe . Also not to miss any new videos remember to hit that notification 🔔 *** Thank you for watching I really appreciate your support.*** Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@DialCj-pf3mf]

I just want to say thank you for the video it's saved my butt when I lifted it out it fell to the ground I did not see where it went your video help me very much and thank you

[@JOEZEP54]

You're welcome, I am glad this was of help. And thank you for watching and taking the time to comment. @DialCj-pf3mf I have other videos on my channel that cover different subjects and new videos added weekly that may also be of help or interest. Your support is not required but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and sharing this content do help. Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@greggoldman893]

Thanks Joe! I looked everywhere for a diagram or rebuild kit and wasted a lot of time. I had that jet in three of the wrong places on that plastic piece. Your video showed how I needed to orientate the jet. Ran like a charm after I cleaned it all up and put it back together. Troy Bilt 5550/8550 watts, B&S 9hp OHV, Nikki Carb 695114….in case anyone is looking for the same advice.

[@JOEZEP54]

You're welcome, I am glad this was of help. And thank you for watching and taking the time to comment. @greggoldman893 I have other videos on my channel that cover different subjects and new videos added weekly that may also be of help or interest. Your support is not required but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and sharing this content do help. Stay safe, Joe Z

[@welostourdemocracy]

I don't know what it is about that jet for the folks in other videos but you're the only one who saw the need to tell everyone where that main jet came from and how it goes back in. I must have watched 7 videos. A couple of people came close but stopped short.

[@JOEZEP54]

I am glad this was of help. And thank you for watching and taking the time to comment. WeLostOurDemocracy I have other videos on my channel that cover different subjects and new videos added weekly that may also be of help or interest. Your support is not required but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and sharing this content do help. I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@davids4727]

Thank you very much for posting this. I was wondering which way the jet went. I watch so many videos, but your video was the only one that made a difference in helping me.

[@JOEZEP54]

I am glad this was of help .And thank You for watching and taking the time to make such an positive comment !! It is really encouraging & appreciated. When you get a chance check out my video playlist for other videos that may be of help & interest to you. Be sure to👍 , share & $ubscribe if your are inclined to do so. Stay well Joe Z

[@anachronisticthings6816]

Thanks for this! Saved me a lot of trouble.

[@JOEZEP54]

Anachronistic Things, You're welcome, I am glad this was of help. And thank You for watching and taking the time to comment. Anachronistic Things I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share and subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. *** Thank you for watching I really appreciate your support.*** Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@michaelhennessey3591]

Joe you Da man! When disassembling my carb that main Jet fell out and I could not figure out where it came from! LOL. You're the best. God bless

[@JOEZEP54]

Glad to help. Michael Hennessey, You're welcome, .And thank You for watching and taking the time to comment Michael Hennessey. I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to like, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Stay safe, Joe Z.

[@catferdcoin3681]

You answered the EXACT question I had!

[@JOEZEP54]

Glad this was of help. Thank you for watching & taking the time to comment. Stay safe, Joe Z

[@biker41445]

Joe I will join the crowd and say thanks for taking time to show us where and how the main jet went into the carburetor body correctly. I too looked at dozens of videos and Briggs and Stratton exploded carburetor diagram but none of them showed you where it went. Thanks again and stay well!! 🔧🛠⚙️

[@JOEZEP54]

biker41445, You're welcome, I'm glad this was of help .And thank You for watching and taking the time to comment welcome to the crowd, it is always a pleasure to hear that one of my videos helped someone out. biker41445 I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Stay safe, Joe Z.

[@victoryfirst2878]

Can you please tell me if the float in the closed position is parallel with the hinge holding roof when looked at from the side ???? Thanks VF

[@JOEZEP54]

It has been awhile but If I remember correctly it had a slight tilt. Unlike the older carbs with metal tabs it is not adjustable. Thank you for stopping by. Let me know if this was of help. Stay safe, Joe Z

[@victoryfirst2878]

@@JOEZEP54 Joe you are correct of a slight tilt. But most Nikki 6 carburetors I call dickie carbs always have something wrong with them. I fixed just to many of them. Your video is right on Joe. Wish other KZbinrs could get the idea and make videos that have pertinent information for the community to use and learn from. Good day and peace too. VF

[@JOEZEP54]

@@victoryfirst2878 Thank you for this comment it is very much appreciated, Hope to hear from you again. Be sure to stay safe, Joe Z

[@victoryfirst2878]

@@JOEZEP54 Thank you so much JOE Z. I plan on staying virus free. Peace. VF

[@JOEZEP54]

@@victoryfirst2878 You're very welcome.👍

[@missbettyboop1953]

Great video. A little out of focus, but it saved me a lot of time trying to figure out where the main jet fell out from. Screws were very difficult to remove. Thank you.

[@JOEZEP54]

The focus could have been better but glad you still found it useful. Your support is appreciated, Thank you. Stay well, Joe Z

[@SeekerFor1000]

Hi Joe. Greta video. I pulled the bowl off (no solenoid on the bottom) and the spring and the jet fell out. Thankfully they fell into the bowl. Appreciate the explanation of how and where it goes. And your video is a touch fuzzy but excellent. You explained everything. The carb is still on the engine (a Generator) and I am wondering how i get the float to stay in place while I ut the bowl and spring up against it? Thank you!

[@JOEZEP54]

Thank you for your comment. I do appreciate it. As far as the float the hinge pin should hold it in a hanging position. It has been awhile I am not sure of the spring you mentioned. Also was the solenoid replaced with a bowl nut or just never had one? Just curious. Stay well, Joe Z

[@johnbercier3229]

Thank you for the video. Helped me figure out how to reinstall the jet that fell onto the garage floor.

[@JOEZEP54]

Glad it helped John Bercier, You're welcome and thank You for watching and taking the time to comment. John Bercier I have other videos on my channel that cover many different subjects that may also be of help or interest. Be sure to 👍, share &; subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. *** Thank you for watching I really appreciate your support.*** Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@jacobhensley3035]

Thank you for your video. You saved me alot of money. I had main jet fall out last year. It took me forever to find it and even longer to realize what it was. Untill today i had not had any clarification as to where or which way it goes, this video answered it all and my mower is running again. Thank you again, really helpful video.

[@JOEZEP54]

Hey Jacob Hensley, You're welcome I am glad this was of help. Thank You for watching and your comment is very much appreciated! I have other videos on my channel that cover many different subjects & new videos added weekly, so check out my video playlist for other videos that may be of help & interest to you. Be sure to hit the notification bell not to miss any new videos. . Like, share & subscribe if your are inclined to do so.Happy mowing 🙂 & until next time, Stay well Joe Z

[@jakxian3690]

I agree with Donald Barnett - yours is the best video I've found on KZbin explaining the main jet position. It fell out when I opened my Nikki carburetor, like you described. Wasn't sure where to put it (inside or outside of tube?) until watched your video. Was only piece of info hanging me up with finishing rebuild. Thanks for great info!

[@JOEZEP54]

Jak Xian, You're welcome, I am glad this was of help .And thank You for watching and your kind comment. I do appreciate that. Jak Xian I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 If you like you can help support the channel at NO cost to you by using one of the above affiliate links. Let me know any thoughts you have in the comments! Thank you again. Safe, Joe Z

[@hbui2916]

Thanks! 4 years later you helped me figure out where the jet went and Found that I didn’t put that o ring back in and was flooding the engine and couldn’t figure out why 🤣

[@JOEZEP54]

H Bui, You're welcome, I am glad this was of help. And thank you for watching and taking the time to comment. H Bui I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Your support is not required or expected but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and using the following links do help Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@michaelbidwell4210]

I've done dozens of carb rebuilds and somehow missed the jet falling out into the gravel part of my driveway. Put it back together and couldn't figure out why it ran like crap so I put it up for the winter. Pulled it back out to fix the deck this week. Disassembled the carb again and I still didn't notice the jet missing. Your video helped me realize I was missing the jet and an O ring. Thanks

[@JOEZEP54]

Michael Bidwell, You're welcome, I am glad this helped .And thank You for watching and taking the time to comment. Michael Bidwell I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. *** Thank you for watching I really appreciate your support.*** Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@race091]

Haha I tore apart the carb on my pull behind finish mower so many times it would not run right I knew it was a fuel problem but couldn't figure out y till this video I had the main jet in wrong thanks for the video

[@JOEZEP54]

You're welcome, glad this was of help. Thank you for taking the time to comment. Your commenting helps me with this channel and your sharing it, 👍s and subscribing if you're inclined to do so would also help and be most appreciated. Stay well, Joe Z

[@acoupetroop617]

Thanks a bunch for showing where the jet actually goes. I've watched about 50 different vids and they all manage to skip that part

[@JOEZEP54]

acoupe troop, You're welcome, I am glad this was of help. And thank you for watching and taking the time to comment. acoupe troop I have other videos on my channel that cover many different subjects and new videos that may also be of help or interest. Your support is not required or expected but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and using the following links do help. Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@acoupetroop617]

I'll be sure to check them out

[@JOEZEP54]

@@acoupetroop617 Thank you.

[@ronrussell6716]

Very good mate I did not know where that bloody jet went thanks mate

[@JOEZEP54]

Glad I could help and thank you for taking the time to comment. If your are incline to do so your subscription, likes & comments would be appreciated. Hope to hear from you again. Stay well, Joe Z

[@davidheider13]

Thank You. This was Very Helpful as I took apart the carb on my Swisher mower yesterday and that main jet fell out when I turned it over. And as you said it can fit in a few different places. And I didn't see where It fell out of. I had to use an impact driver to take those 2 bowl screws out. Thanks again.

[@JOEZEP54]

David Heider, You're welcome I am glad this was of help .And thank You for watching and taking the time to comment !! I have other videos on my channel that cover many different subjects & new videos added weekly, so check out my video playlist for other videos that may be of help & interest to you. Be sure to hit the notification bell not to miss any new videos. And if you would like to help do not forget to give it a 👍 & to share my channel with others. Stay well, Joe Z.

[@jilldriggers2728]

Thank you very much somebody else took my carburetor apart and I did not know where the main jet win great video

[@JOEZEP54]

Jill Driggers, You're welcome, I am glad this was of help .And thank You for watching and taking the time to comment. Jill Driggers I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of the above affiliate links. *** Thank you for watching and your support I really appreciate it.*** Stay safe, Joe Z

[@MA-SH]

Very nice friend 🙂🇷🇺

[@JOEZEP54]

Much appreciated.

[@billyanthony8153]

where can the little o ring be bought i cant find it and the one in link dont show it in the picture

[@JOEZEP54]

Hi billy, Off hand I do not remember the size of this o ring. Take a look a this kit, just make sure the number is the same as on your carb amzn.to/3bgPnEG Also if you can measure the o ring check out this o ring assortment to see if it has the size you need. amzn.to/3y1RiGM Let me know if this was of help. Joe Z

[@silwan6784]

Thanks for video. Happened to me exactly and could not figure out. Your camera work is stupendous.

[@JOEZEP54]

You're welcome! Thank you for watching & taking the time to comment. Stay safe, Joe Z

[@itsmeforsure5475]

A 1000 thumbs up for focusing on how the jet goes in. I've watched a 1000 videos and not one mentions how it goes in and nor can I find a diagram online.

[@JOEZEP54]

I am glad this helped. Thank you sooo much. I really appreciate your support. Stay safe, Joe Z

[@michaelfarr4951]

thanks for the video saved me alot of time...I had snowblower up on end to service bottom parts when I was finished I could not get blower started gas coming out of carb sputering back firing etc..Found that all gas from tank ran into crankcase oil...changed oil 4 times to try and fix... took carb apart and found small part in bowl !!! which after seeing your video found where it belonged.. put carb back together changed oil again and machine ran cleared itself out and now runs great.. I would like to know how main jet got to the bottom of carb bowl before I took it apart thanks

[@JOEZEP54]

Michael Farr, You're welcome, I am glad this was of help .And thank You for watching and taking the time to comment. As far as how the main jet got to the bottom of carb bowl before you took it apart the only thing I can think of is that maybe someone started to clean the carb prior to you getting to it. Michael I have other videos on my channel that cover many different subjects and new videos added weekly ( been behind on videos lately🙄 ) that may also be of help or interest. Be sure to like, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Stay well, Joe Z.

[@Bunky1267]

We are working on one of theae carbs but it doesn't have the fuel cut off. It's on a generator and it only wanted to run smooth on 1/2 choke.. so we took it apart everything looks clean put in a kit. Now it runs off choke but surges. Could this be the oring on the main jet?

[@JOEZEP54]

Thank you for stopping by. If the o ring on the main jet is missing or deformed it would cause flooding. You may still have some debris clogging a passage, it doesn't take much. Dose your carburetor have a "hidden" jet on the top. If this is clogged it would cause surging. Before you take it apart again check to see if the mounting gaskets are in place & everything is tightly secured. An air leak will cause surging. Let me know how the repair goes. Stay safe, Joe Z

[@dantucker7402]

Thanks, saved my butt on where the main jet goes cause when I pulled everything out if the ultrasonic cleaner there was the jet which I had no idea where it came from👍

[@JOEZEP54]

You're welcome dan, I am glad it helped. Thank you for the 👍 & comment. This along with sharing this channel & subscribing help me to continue making these videos. Stay well, Joe Z

[@cummins110declanmaccarthy8]

Exactly what I needed. The main jet fell out like you said and I didn't know where it went. Thanks for the presentation. Excellent.

[@JOEZEP54]

You're welcome, I am glad it helped. Thank you for visiting & taking the time to comment. I appreciate your support. Stay safe, Joe Z

[@kevinthompson6986]

Mine fell out too I think it needs new plastic pieces

[@pogtuber5146]

Rubber o-ring down dropped into the tube and pushed in, thanks bro, literally all I needed to know I appreciate this video

[@JOEZEP54]

You're welcome, I am glad this was of help. And thank you for watching and taking the time to comment. @pogtuber5146 I have other videos on my channel that cover different subjects and new videos added weekly that may also be of help or interest. Your support is not required but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and sharing this content would help. This is always appreciated. I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@InstantRyPlay]

Great video Joe! I am not mechanically inclined, but really like watching your videos and learning new things! Thanks so much for sharing!👍

[@JOEZEP54]

Thank you for your kind words and taking the time to comment. Is is much appreciated. I am glad that you enjoy my channel and find it use full. If you have any questions let me know. Stay well, Joe Z

[@johnconrades2324]

As others have said, great details on Nikki main jet, very concise. I have been resurrecting old Murray rider and "repairing" Nikki carburetor for several days now and keep finding out what I'm doing wrong. This video has shown me that the jet is installed upside down. Now if those new gaskets would only arrive....

[@JOEZEP54]

John Conrades, I am glad this was of help .And thank You for watching and taking the time to comment. It took me a little time to figure this out myself. John Conrades. I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to like, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Stay well, Joe Z.

[@mikeuva2273]

thanks for the video if the idle circuit is clogged where would i look for the jet to clean? where is the idle jet?

[@JOEZEP54]

You're welcome and thank you for taking the time to comment. I do not have a clear shot of the idle jet, but at 2:58 when I remove the plastic piece it will be under there. It is flush in the the body of the carb. It will be a brass color. Stay safe, Joe Z

[@silentwalk1768]

Thanks I took it apart for cleaning and thanks to you I found out where the jet went you're right can go a few different places thanks a lot yeah the older ones were threaded not these ones

[@JOEZEP54]

Silent Walk, You're welcome, I am glad this was of help. And thank You for watching and taking the time to comment. Silent Walk I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share and subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. *** Thank you for watching I really appreciate your support.*** Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@kevinthompson6986]

I wonder if it was changed because of stripping the brass jet?

[@samararugar5412]

Hey grandpa!!! How are you doing? I miss you and everyone else!!!!!! I hope I’ll get to see you guys soon! Love you!!!! Great job on your KZbin channel!

[@JOEZEP54]

Thank you.. Be good 😐

[@SimplyShannan]

You are so aknowledge on all car issues I believe!! Another great video.

[@JOEZEP54]

Thank you, and I am glad you my channel. Your comment is much appreciated. Stay well, Joe Z

[@raypowell4804]

Do you have a vid on reinstalling and tuning this carb?

[@JOEZEP54]

I do not think I have a video showing the adjustment on this carburetor. If you have to adjust it loosen the adjusting screw to richen and tighten to lean it out. These motors will run a "little" rich no problem (too rich will cause carbon build up) but they will not run right if too lean. If it runs too lean with it loosed all the way out you can pull/break off the plastic limiter cap and move it further to make it run richer (turn lefty loose to richen) and it will help your engine in the cold. If its cold outside they like to be a little rich but If its hot out they like to be just right. Let me know if this was of help and thank you for stopping by. Stay safe, Joe Z

[@mikehopper8897]

Get video. Was very helpful. Thanks

[@JOEZEP54]

You're welcome, I am glad this was of help. And thank you for watching and taking the time to comment. @mikehopper8897 I have other videos on my channel that cover different subjects and new videos added weekly that may also be of help or interest. Your support is not required but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and sharing this content would help me to reach other viewers that may also find this channel useful or entertaining. Stay safe, Joe Z

[@geoffdunstan8567]

Thanks Joe, just got a Murray ride on with bad flooding. These videos are a great help. Regards, Geoff from Merimbula Australia.

[@JOEZEP54]

Hello Geoff, You're welcome I am glad this was of help .And thank You for watching and taking the time to comment !! I have other videos on my channel that cover many different subjects & new videos added weekly, so check out my video playlist for other videos that may be of help & interest to you. Be sure to hit the notification bell not to miss any new videos. And do not forget to give it a & to share my channel with others. Have a KZbin Channel? If you haven't installed the TubeBuddy browser plugin yet, to help your channel grow do it! Just go to www.tubebuddy.com/joezep54 Start with the free version, yes it is free to not only to down load but to use.I hope you enjoy other videos on my channel as well. Be sure to like, share & $ubscribe if your are inclined to do so. Stay well Joe Z

[@Cards-In-The-Closet]

I had to use vise grips on those dang screws! Thanks for telling us how the main jet is placed.

[@JOEZEP54]

CentexRocket, You're welcome, I am glad this was of help .And thank You for watching and taking the time to comment. Those screws can be a pain to get out. CentexRocket I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Stay safe, Joe Z.

[@jeffglueck4099]

Yeah, me too ! I twisted a DeWalt Phillips Bit on them!

[@larrycox3378]

good job Joe watched other video , like about 10 or so it seemed , took carburetor apart , main jet fell out - what the hell is this and where does it go then I found your video ,thank you

[@JOEZEP54]

Larry , Thank You for watching and taking the time to comment.You're also welcome, I am glad this was of help . I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to like, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Stay well, Joe Z.

[@ericwilliams3134]

This is a great video. Saved me some money for sure. Glad I ran across your channel...whuuuu!

[@JOEZEP54]

Awesome! Thank you for your comment. Eric Williams, You're welcome, I am glad this was of help .And thank You for watching . Eric Williams I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. *** Thank you for watching I really appreciate your support.*** Stay safe, Joe Z

[@JohnCRV]

Very good instructions Joe, Full View and a like. Have a great day.

[@JOEZEP54]

Thank you John! Heading your way

[@idontwantachannelimjustcom7745]

I took my carb apart, and couldn't find the jet. Wanted to clean the brass stem thinking my jet was different. Watched your vid and during reassembly found the jet in the plastic piece. 20mins and 8 bolts/screws to get the bowl off with the carb on the mower. 20 seconds to clean jet.

[@JOEZEP54]

I am glad this was of help. And thank You for watching and taking the time to comment. I don't want a channel I'm just commenting I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share and subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. THANK YOU for taking the time to check out my page and watch my videos. Your likes, & comments are are much appreciated and I will respond to them as soon as possible. Even your dislikes if you leave a comment as to why. Your support is not required or expected but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and using the following links do help. *** You can Help Support The Joe Z Channel at no cost to you*** by following my affiliate links. Joe Z is a participant in the Amazon Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon, that helps me to continue producing videos. I am building SOMETHING NEW to my channel. Joe Zs on line Store at: www.amazon.com/shop/joez Thank you for your support and using the links provided to make your purchases. It is a Win/Win!!! And always appreciated!!! If you do not have Amazon Prime no problem: Enjoy this special offer: Try Amazon Prime for one month FREE TRIAL (After one month, Prime is $12.99/month plus any applicable taxes). Click amzn.to/36QXdCj Cancel anytime Click amzn.to/36QXdCj *** Thank you for watching I really appreciate your support.*** I don't want a channel I'm just commenting I just want to mention If you haven't installed the TubeBuddy browser plugin yet, to help your channel grow Just go to my favorite tool for channel growth Tube Buddy. Now You can use it too, here's my affiliate link to the Free versionwww.tubebuddy.com/joezep54 Start with the free version, yes it is free to not only to down load but to use. Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@markt.7377]

You are right about the bowl screws. I used the largest slotted screw driver that would fit, and it worked well.

[@JOEZEP54]

Mark T., I am glad this was of help .And thank You for watching and taking the time to comment. I have other videos on my channel that cover many different subjects & new videos added weekly, so check out my video playlist for other videos that may be of help & interest to you. Be sure to like, share & subscribe if your are inclined to do so. Stay well Joe Z

[@jeffglueck4099]

Ballz!! I just put my carb back on with the Main jet upside down!!! I hope I didnt smash anything on that plastic....oh well, a new carb is cheap enough. But I wish I saw this first. Thanks

[@JOEZEP54]

Jeff Glueck, You're welcome, and thank You for watching and taking the time to comment. Jeff Glueck I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 You can support the channel at NO cost to you by using one of the above affiliate links. Let me know any thoughts you have in the comments!Thank you for watching and subscribing!Stay safe, Joe Z.

[@Pinkstonfamily123]

Really nice video thank you for sharing have a great night

[@JOEZEP54]

You're welcome & thank you for your kind words & $upport. Stay well, Joe Z

[@FourthWallPro]

THANK YOU! I was lost on where that main jet fell out from. 🙏

[@JOEZEP54]

Fourth Wall Productions, You're welcome I am glad this was of help .And thank You for watching and taking the time to comment !! I have other videos on my channel that cover many different subjects & new videos added weekly, so check out my video playlist for other videos that may be of help & interest to you. Be sure to like, share & subscribe if your are inclined to do so. Stay well Joe Z Have a KZbin Channel? If you haven't installed the TubeBuddy browser plugin yet, to help your channel grow do it! Just go to www.tubebuddy.com/joezep54 Start with the free version, yes it is free to not only to down load but to use.I hope you enjoy other videos on my channel as well.

[@dj5752]

Nice video. I just subscribed.

[@JOEZEP54]

Awesome, thank you! Let me know if I can be of additional help. Stay safe, Joe Z

[@chadr00]

I've been installing the jet with oring side facing up toward pick up tube. Isnt the oring supposed to seal against the brass pick up tube? Thanks.

[@JOEZEP54]

Thank you for watching & your question. As far as I know this is how it should be. It is working as it should installed as I showed in the video. Your explanation sounds reasonable & is working for you , now you got me curious LOL. Stay safe, Joe Z

[@chadr00]

@@JOEZEP54 I think I was installing it backwards. I found this web site "Disassembly, Cleaning and Repair of Briggs and Stratton Intek Single Cylinder OHV Nikki Carb" at outdoorpowerinfo.com/repairs/briggs_intek_single_ohv_nikki_carb.asp where it explains that all fuel goes through the main jet. The fuel for the idle circuit also must go through the main jet so it makes sense to have the main jet oring seal tightly against the bottom of the plastic tube instead of sealing against the brass pick up tube.

[@JOEZEP54]

Thank you for the follow up information & link. It is much appreciated. Hope you get a chance to view & enjoy some more of my channel. Your comments are not only interesting but helpful. Thanks again, JOe Z

[@ronwilson8397]

Saved me brother..main jet fell out couldnt find where

[@JOEZEP54]

Ron Wilson, You're welcome, I am glad this was of help. And thank you for watching and taking the time to comment. Ron your support is much appreciated. Thanks again and stay well, Joe Z

[@joesphbaumgardner4579]

@JOE Z Thanks for vid. Need some input please. I have cleaned etc few carbs in my time. Mostly two stroke, but few on push mowers. I have not fully rebuilt one however understand most of what is. I have a used older Yard Machines rider I brought. By the gas line I could tell bad gas was in carb. I should of left alone because mower ran fine. But I knew that carb had crap in it. I made the mistake of opening it. The carb is pretty much like yours. Mine is a Nikki same style. Yeah the little brass with O ring fell right out and I was like great where the hell does it go. I suspected it went in spot you show. Problem was I was tossing what way it goes, but that issue is solved. So the carb did have white junk in it. I cleaned the carb with carb cleaner inside and out. More less looks new now. Bolt it to mower and leaks out center side gas a tad. Also throws gas ( out choke flap side ) in large amounts out breather tube every time mower is turned off and back on. When running that stops so please note that one. At this time I am at my wit ends. Here is why aside from issues I mention. For me the worst part in this was the round big bowl gasket. Worst thing I ever seen and why can't it just sit in the groove of bowl. It wants to pop out of each side and all else. A nightmare I tell you. So how exactly is this done? Gasket sits round at the very edge of white plastic all the way around? I did order a rebuild kit but before I install stuff or mess up the new gasket I will hold till you reply. So I can better understand the gasket install. The kit I got was -- # 799727--. I do see parts in it that appear some do not go in my carb. Is that common with these kits? Stuff I can't id as well like a little round silver cap or something. Lastly on the subject of carb issues I do notice my float is not lined center and it sags down a good bit. What is likely I need to do to solve the issues? Darn thing worked fine till I opened it lol. Side note also- the bigger round O ring that sits down in carb that the nub of the plastic sits in. That O ring looks to be bad. It has a shred of rubber hanging on one side. You wouldn't happen to have a FULL vid of a full rebuild on this carb would you? Like how to remove the brass seat etc also on this one......

[@JOEZEP54]

Joesph Baumgardner, I read your question about 1:00 am last night but it was just too late to respond. I noticed you crossed out some of your questions. I am guessing that you figured that part out. That little round silver cap is a welch plug. It is to replace the one installed if you removed it to thoroughly clean the carb & yes depending who you buy the parts from is is common to get extra parts that my not be for you particular model. If that big o ring is damaged the carb will flood. This is a common issue with these carbs. I have to check to see if I have a full carb rebuild. In this video if you go to 4:04 & slow the video down ( go to the setting icon & click play back speed) this should help you with the bowl gasket. Let me know if this was of help. Joe Z

[@joesphbaumgardner4579]

JOE Z As for the crossed lines I did not do that. I have had that happen before and don't know why. I have also seen it before with others. Must be a KZbin thing. I did however manage to rebuild this carb last night. Took me a good while. But now I understand a bit more. The big gasket went on pretty well with no issue when I watched your vid slowly. The issue was the kit and little O ring and brass that fits in center tube upward.The ring was fatter or brass was. So I had to reuse my old which worked. Also the bigger O ring that sits on plastic nub for main gas. That was thicker and a pain to get all locked down tight. After forever I managed. Moment of truth when I got up was to run gas and fire up mower. Verdict no leaks or flood in oil. Works great. I did not see a welch plug in my carb and I gutted it all down and cleaned and rebuilt. As for the seat I mentioned in first reply, I see now there is no seat. Well, the plastic and sealed is pretty much it. So I did not have to worry about remove of seat. Any event all is well. I may shop around and try differ kits till I get exact O rings and brass. I have another Nikki to rebuild and have to learn it. It appears gasket is slightly differ and carb that has spring under bowl unlike mine I did.

[@JOEZEP54]

@@joesphbaumgardner4579 I am glad you got it together, up & running👌. These carbs take a little getting use to. That plastic piece where the seat is can sometimes warp, so look for that when you rebuild your other Nikki. I had a little time getting that o ring on myself. In the video I showed how I rolled it off a screwdriver. If you have trouble putting it together wipe a little 2 cycle oil on it. Hey if you would like to give a hand & are inclined to do so give this video a 👍, share it & subscribe. Stay safe, Joe

[@joesphbaumgardner4579]

@@JOEZEP54 Will do. Thanks for time and reply. As for the O ring I did lube. It was the one that goes on plastic nub and sits down in where gas comes in I think. Getting it on nub was no issue. Getting the ring locked down in hole was the pain. Being that ring looked alot fatter than my old. Any event I use 90 no eth gas so unlike prior owner the carb should not be trashed and me back in it lol.

[@JOEZEP54]

@@joesphbaumgardner4579 That ethanol is the worst thing made for these small engines. O rings, gas lines, diaphragms & even the aluminium bowls get destroyed. Unfortunately for us in my county they do not sell non ethanol. The only options are buying pre mix in the big box stores at $7.00 plus a quart or just stay on top of the maintenance.

[@PamL-mj3iq]

Thank you!!!

[@JOEZEP54]

You're welcome! Glad this was of help, thank you for watching and taking the time to comment. Your commenting, sharing, 👍s and subscribing would be a big help & much appreciated. Stay well, Joe Z

[@jackzuranski852]

great tip

[@JOEZEP54]

Glad it was helpful and thank you for watching and taking the time to comment. Stay well, Joe Z

[@REVNUMANEWBERN]

Can you take the center brass tube out???

[@JOEZEP54]

Numa Newbern, Thank You for watching. I left it in & cleaned the out the small holes in the tube with a thin bread tie wire. Then sprayed carb cleaner. Be careful not to get carb cleaner on any of the gaskets. Hope this is of help. Stay well, Joe Z.

[@saneauto]

I have a set of those Craftsman screwdrivers too. There great tools.

[@JOEZEP54]

I can not remember how long I had these. When I have to get serious they are my go to tools. I will probably get a few comments from the snap on guys LOL.

[@JimHenderson19]

I liked and subscribed!!

[@JOEZEP54]

Thank you Jim. I do appreciate your support. Let me know if I can be of help with your future projects. Stay well, Joe Z

[@paultillmann2918]

Another great video Joe. Had a similar setup that this helped me with. Thanks for the great info. I’ve learned a couple things from you already. You make great videos. Keep up the great work.

[@JOEZEP54]

Hi Paul, I am glad this video helped you out. Thank you for such a complimentary comment. It definitely helps & is much appreciate! Stay well, Joe Z

[@charlesyoung4744]

should the float be level or slanting down

[@JOEZEP54]

Hello Charles Young, The float will slant down when you hold it upside down putting the bowl back on. Let me know if this was of help. Stay well, Joe Z.

[@johng9444]

Great video I didn't know where main jet belonged when it fell out onto bench. My gaskets & needle are on order, thanks for sharing your knowledge!

[@JOEZEP54]

John G, You're welcome, I am glad this was of help .And thank You for watching and taking the time to comment John G. I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to like, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Stay well, Joe Z.

[@allan2524]

Thanks wasn't sure if O-RING went in first from other people sites. If had found your site first would have known where main jet fell out from and how to install.

[@JOEZEP54]

You're welcome,I am glad this was helpful. Thank you for taking the time to comment,👍 Stay safe, Joe Z

[@madscientisthut]

Nice video Joe! Useful info, LIKE+

[@JOEZEP54]

Thank you !!

[@stevenbaumann8692]

Thanks for the great info!

[@JOEZEP54]

Steven Baumann, You're welcome, I am glad this was of help .And thank You for watching and taking the time to comment. Stay safe, Joe Z.

[@joshuaheart2764]

Thank you

[@JOEZEP54]

Joshua Heart, You're welcome I am glad this was of help .And thank You for watching and taking the time to comment !! I have other videos on my channel that cover many different subjects & new videos added weekly, so check out my video playlist for other videos that may be of help & interest to you. If your are inclined to do so be sure to hit the notification bell not to miss any new videos. And do not forget to give it a 👍 & to share my channel with others. Stay well, Joe Z.

[@charlesroberts3838]

Your video was the best one I saw on this model carb , are you a New Yorker , I like the way you said warp you said wawp not making fun of you we are all different

[@JOEZEP54]

Thank you for your kind comment. I am glad it was of help. Yep I am a New Yorker, living upstate for over 48 year now, the accent is fading slowing. I heard that I am different 🤣 Stay well, Joe Z

[@totalrecone]

Hi Joe. A million likes for your great instructional video on how to find where that jet goes. It's helped me tremendously. One thing I noticed about this model carb is that the rubber needle valve that rides on the float doesn't have a metal seat to mate with. Is this how it should be or have I lost another bit to this thing? Cheers from ɐᴉlɐɹʇsn∀

[@JOEZEP54]

You are very welcome. I am glad this helped you out. Thank you for taking the time to comment.You're doing fine, this carburetor doesn't have a metal seat. If you have any other questions let me know. Also if you are inclined to do so you subscribing, giving a 👍 and passing my channel to others would be a big help and most appreciated. Happy mowing , you and yours stay safe down under, Joe Z

[@roninthenek4530]

My main jet won't stay seated. Is that normal?

[@JOEZEP54]

It does slip, but still check the o ring. ron in the NEK, Let me know if this was of help. And thank you for watching and taking the time to comment. ron in the NEK I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Your support is not required or expected but always appreciated. If you are inclined to do so your Subscription, Likes, Comments and using the following links do help. You can Help Support The Joe Z Channel at no cost to you by following my affiliate links. ******* Thank you for your support ******** Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@johnsilvey3208]

Hi - very helpful video - that small jet with the o-ring on it was confusing me. You clearly answered that question - Thanks ! Appreciate the time you took to make and post this. Only thing that could be better would be a better focus and less moving around of the camera (I get motion-sick too darn easy ...).

[@JOEZEP54]

John Silvey, You're welcome I am glad this was of help .And thank You for watching and taking the time to comment. I am always open to constructive criticism & I do keep it in mind. I have other videos on my channel that cover many different subjects & new videos added weekly, so check out my video playlist for other videos that may be of help & interest to you. Be sure to like, share & subscribe if your are inclined to do so. Stay well Joe Z

[@Karlacook89]

Hi Joe! Nice video👏👍🤗

[@JOEZEP54]

Hi Karla,thank you & good to hear from you, hope all is going well.

[@JIB310]

Liked the video good stuff keep up the good work rantjam stream subbed as well i support u....keep bringing out more videos man

[@JOEZEP54]

You're kind comment & support is much appreciated. Your channel has helpful content as well keep it up and continue to grow. Joe Z

[@garryludwick2990]

Tp get the 2 screws out that hold the bowl, use a GOOD ViceGrips. Straight in and tite. Crack loose then use screwdriver

[@JOEZEP54]

Hi Garry, thank you for visiting & taking the time to add useful content to this video. Hope you get to visit regularly & continue to help with your suggestions, Stay safe, Joe Z

[@garryludwick2990]

@@JOEZEP54 Hey Joe, I'm into restoring the old 60/70 tractors, the OH120, HH120 type with the Walbro LMH, and the Briggs with the Flow-jet carbs. Rite now I'm arguing with a LMH17. Keeps flooding, been thru it 3 times already. Beating me to death

[@JOEZEP54]

@@garryludwick2990 If the seat & needle are good maybe the float. The older ones have the metal float & some time they leaked & once a little gas got into them they no longer floated & shut off the gas flow.

[@maloo3049]

great video , just had the jet fall out on me as it did in the video , thanks....another aussie viewer......

[@JOEZEP54]

maloo 304 You're welcome I am glad this was of help .And thank You for watching and taking the time to comment !! I have other videos on my channel that cover many different subjects & new videos added weekly, so check out my video playlist for other videos that may be of help & interest to you. Be sure to hit the notification bell not to miss any new videos. And do not forget to give it a 👍 & to share my channel with others. Stay well "down under", Joe Z.

[@Jim-ie6uf]

Well done, Joe!

[@JOEZEP54]

JOE Z 35 seconds ago jim s, Thank You for watching and taking the time to comment. I hope this video was of help. jim s if you haven't installed the TubeBuddy browser plugin yet, to help your channel grow, just go to www.tubebuddy.com/joezep54 Start with the free version, yes it is free to not only to down load but to use.I hope you enjoy other videos on my channel as well. Be sure to like, share & subscribe if your are inclined to do so. Stay well Joe Z

[@larencegagland506]

Great vid, what the best way to get the o ring on the jet?

[@JOEZEP54]

Thank you for watching & your comment. It is a little tricky because of the size but the only way I know of is to rest it on your flinger tip & worked it onto the jet. Patience & a steady hand, maybe a small needle nose plier to hold the jet. Sorry I do not have a better explanation. Let me know how you got it on. I'm always looking for different ways to get things done. Stay safe, Joe Z.

[@compresswealthdivideeconom3757]

This is confusing. Apparently there are so many variations. The jet on the nikki carb I have going along with Briggs 40N877, I have to pop out the jet the other way out the tube. Impossible to go the opposite way as the brass tip is wider than the end of the tube. Anyone with great expertise, please affirm I am understanding this correctly.

[@JOEZEP54]

I agree it can be very confusing the first time or 2 you run into these. You can have the same engine but a different year or on different lawn tractor with the same name carb. but a different version of it. If yours is not like the one I have in this video Google the carburetors model # & check for a rebuild kit. You may find a diagram of your carb. depending on the site. Hope this helps. Joe Z

[@compresswealthdivideeconom3757]

@@JOEZEP54 I think someone at the factory installed it incorrectly. I will put in as shown here. As seen on another video it 'looks' like it's positioned correctly feeding in at the top and maybe a new worker did just like that, or a worker who knew better thought of playing a joke.

[@JOEZEP54]

@@compresswealthdivideeconom3757 Could have been on Fridays production line LOL. Let me know how you make out. Come back to visit again. Stay well, Joe Z

[@michaelmassey7897]

Thanks a ton- saved my ass .

[@JOEZEP54]

Michael Massey, You're welcome, I am glad this was of help .And thank You for watching and taking the time to comment. Michael Massey I have other videos on my channel that cover many different subjects that may also be of help or interest . If you would like to help out be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. *** Thank you for watching I really appreciate your support.*** Michael Massey I just want to mention If you haven't installed the TubeBuddy browser plugin yet, to help your channel grow Just go to my favorite tool for channel growth Tube Buddy. Now You can use it too, here's my affiliate link to the Free versionwww.tubebuddy.com/joezep54 Start with the free version, yes it is free to not only to down load but to use. Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@Doomzdayxx]

Sir, may you live to be a thousand years old.

[@JOEZEP54]

I thank you Sir & may you live a long & healthy life. Doomzdayxx, You're welcome, I am glad this was of help .And thank You for watching and taking the time to comment. Doomzdayxx if your are inclined to do so 👍, share with others that may also find my channel useful & subscribe. This would be a big help & much appreciated.. Also not to miss any new videos remember to hit that notification 🔔 Another way you can help support this channel at NO cost to you is by using one of my affiliate links. *** Thank you for watching I really appreciate your support.*** Again I hope you get to enjoy other videos on my channel as well. Stay safe, Joe Z

[@lujangaming2354]

Like 1 bro Super Nice upload stay connected full watch time support

[@JOEZEP54]

Thank you! Heading your way :)

[@deanfranklin9239]

i take a #2 phillips bit make sure the tangs are on something solid and tap the bits with a small ball peen works most times. but i had one the other day the bowl was fused to the body

[@JOEZEP54]

Hey Dean thank you for viewing & adding a tip to help out. These carbs can be a challenge at times. Stay well, Joe Z

[@carlosfilipepereira284]

WHAT CARB KIT NUMBER IS THAT PLEASE I NEED TO ORDER ONE AND A MAIN JET

[@JOEZEP54]

Hello Carlos Filipe Pereira Thank you for $ubScribing. It has been awhile since I worked on this carburetor so I had to look up the parts again. If you check in the description I just added a link for the carb kit & a newe carburetor if you decided to go in that direction. If you have Amazon or Amazon Prime this link will flow right to it. If not I also added a link for a 30 day free trial for Amazon Prime which gives you free delivery. Let me know how you did. Stay Well, Joe Z

[@carlosfilipepereira284]

THANK YOU JOE,,

[@JOEZEP54]

You're welcome, it is my pleasure.

[@percywest5448]

enjoyed the video. concise and clear instructions. thank you

[@JOEZEP54]

Percy West, You're welcome I am glad this was of help .And thank You for watching and taking the time to comment !! I have other videos on my channel that cover many different subjects & new videos added weekly, so check out my video playlist for other videos that may be of help & interest to you. Be sure to like, share & subscribe if your are inclined to do so. Stay well Joe Z

[@MrJayprojects]

Thanks a lot I placed the main jet in the wrong place

[@JOEZEP54]

You're welcome. I am glad this was of help. Thank you for taking the time to comment. If you would like to return the help give a 👍 & share my channel with someone else that my find it helpful. Stay safe, Joe Z

[@kds4140]

Thanks

[@JOEZEP54]

KD S, You're welcome, I am glad this was of help .And thank You for watching and taking the time to comment. KD S I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to like, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 Stay well, Joe Z.

[@kds4140]

I would have never figured out where the main jet goes without this video. It fell out when opening carburetor.

[@wcjcnc]

If you want to replace the Nikki carb get on eBay or Amazon and search for Briggs 594603 and look for a carb with a shiny metal bowl and a short stubby fuel solenoid for $30.00 or less. This will be a knockoff of the Walbro carb that is a direct replacement for the Nikki. Other part numbers are 591734, 594605, 591731, 594593, 697202, 594593. The Walbro is much less problematic and easier to work on.

[@JOEZEP54]

wcjcnc, Thank You for watching and taking the time to comment. wcjcnc, the first time I had an issue with one of these I thought the same LOL. There are times when the carb is in good shape & the repair is easy enough. Thank you for posting the Briggs part #. This could be of help to someone that just needs a new carb that stopped by my channel. I also prefer the Walbro Carb. But it may be just what we were use to. I see more & more plastic carbs, which have some advantages but what erks me are plastic gears. Hey stay in touch I will visit your channel soon. Stay well, Joe Z wcjcnc Have a KZbin Channel? If you haven't installed the TubeBuddy browser plugin yet, to help your channel grow Just go to my favorite tool for channel growth Tube Buddy. Now You can use it too, here's my affiliate link to the Free version www.tubebuddy.com/joezep54 Start with the free version, yes it is free to not only to down load but to use.I hope you enjoy other videos on my channel as well. . Stay well Joe Z

[@idiotsinc2241]

The type of screw driver you need is one that's commonly used by electricians. It's a philips screw driver where one blade is bigger than the other. Look at the connections on your circuit breakers. The wide blade is good for producing torque while the smaller blade keeps the driver from slipping and plunging into a box of hot wires. Which they can be even if you've turned off the main.

[@JOEZEP54]

Robert Gustafson, Thank You for watching and taking the time to give this tip. Always good to learn & help others . Robert Gustafson I have other videos on my channel that cover many different subjects and new videos added weekly that may also be of help or interest. Be sure to 👍, share & subscribe if your are inclined to do so. Also not to miss any new videos remember to hit that notification 🔔 You can support the channel at NO cost to you by using one of the above affiliate links. Let me know any thoughts you have in the comments!Thank you for watching and subscribing! Stay safe, Joe

[@baggins1]

Thanks dude. I was all bass ackwards.

[@JOEZEP54]

You're welcome. Glad I got you straightened out LOL Thank you for taking the time to comment. Stay well, Joe Z

[@przemysaw6660]

Very poor film sharpness. Do you insert the nozzle with the new O-ring, O-ring down, or vice versa, because I didn't notice?

[@JOEZEP54]

Watch from 3:40

[@przemysaw6660]

@@JOEZEP54 Thank you. I wouldn't have any doubts if the movie was sharp. The jet falls freely there. Shouldn't it fit tight? The O-ring should not seal the space in the hole, so that the fuel stream only enters through the hole in the jet ?

[@vtl5c3]

I feel less stupid now that I know this has happened to someone else.

[@JOEZEP54]

LOL we all have to learn. Hope this helped. Stay safe, Joe Z

[@billlovett4256]

I hate those Nikki carburetors. I find that using a small pair of visegrip pliers on those screws to first loosen them works well and avoids stripping them.

[@JOEZEP54]

Hi Bill, I know what you mean. These carburetors can be changeling. Thank you for taking the time adding a tip to help out. Stay well, Joe Z

[@Pinkstonfamily123]

💕💕

[@JOEZEP54]

Much appreciated.