Thank you so much for this video. My truck’s idle was surging and nearly dying. I did as you described here and it worked like a charm.
@bbbjim1fixedit Жыл бұрын
Glad to hear
@dubya25143 жыл бұрын
Same problem, it was so old and crusty I just replaced it anyway, one thing to note: if you go around the right side of the throttle body you can pull it right out and unplug it way easier than the left side. Thanks 👍
@bbbjim1fixedit3 жыл бұрын
Good tip
@BobbyGuidry-h3d9 ай бұрын
Hey, just wanted to tell you thank you man that really helped a lot. I thought I was about to have to spend all type of money thank you.
@bbbjim1fixedit9 ай бұрын
Glad I could help
@markvincent2856 Жыл бұрын
Thanks for help... I cleaned it and works fine.. I was having fast idle. Didn't have cleaner so used pb blaster.. thanks again for your help
@bbbjim1fixedit Жыл бұрын
Glad it helped
@Googstuuf Жыл бұрын
Wait what? My idle is a tad high in my opinion. It's runs smooth starts right up. I already used intake cleaner. Did do anything really. Plus it's horrible on gas. No lights are on. Can u advise
@markvincent2856 Жыл бұрын
@@Googstuuf I cleaned the IAC on my truck... it was almost 5grand at idle... took off and cleaned it ... back to normal...
@Googstuuf Жыл бұрын
@@markvincent2856 I did too but it seems like it's idling a tad high. Not running bad or anything but just seems like it's struggling far as trying to pass some one but it's a 6cyl so maybe it's in my head idk. Also horrible on gas .
@No8385811 ай бұрын
@@Googstuufdid you try cleaning your fuel injectors? Or checking the sensor?
@scottb74443 жыл бұрын
Thanks for the video,my ac was making the truck stall way to low idle, thanks!!!
@bbbjim1fixedit3 жыл бұрын
Glad it helped
@tehjosheh5 жыл бұрын
Helped me out a ton, thanks for the video!
@jessenuno42284 жыл бұрын
was your truck shaking as well ?
@tehjosheh4 жыл бұрын
@@jessenuno4228 I did not experience significant shaking
@kalebhorton6564 жыл бұрын
Can we use break cleaner if we dont have the air intake cleaner?
@abinadyoiram3 жыл бұрын
Had the same problem, did exactly as you mentioned and got it fixed! Thanks a lot
@bbbjim1fixedit3 жыл бұрын
Great to hear!
@123-olmngresx Жыл бұрын
Dont clean the IAC just get a new one its probably old anyway. Cleaning the throttle body definitely helps but clean the EGR areas too.
@BOSS_8055 ай бұрын
This is good information that will help a lot of people
@bbbjim1fixedit5 ай бұрын
glad you liked the video
@glenndavidson29434 жыл бұрын
ive done this maybe 4 times to my f150. At least I know the problem.
@chargerscurt4 жыл бұрын
You can buy a new one for about 55 bucks
@anderssoncedillos38352 жыл бұрын
In my case the revolutions go up a little when I turn on the AC and they get normal when I turn it off, do you think this may help?
@bbbjim1fixedit2 жыл бұрын
The engine is supposed to increase in rpms when the air is turned on to ensure the engine does not stall when the a/c compressor kicks in.
@mofopopo4374 жыл бұрын
Sometimes the spring where's out even though we do are best to clean it.
@kahnercalleros82494 жыл бұрын
Is this problem known to f150?
@kimberlyedgins35934 жыл бұрын
Do I need to disconnect battery prior to removing iac? Thanks in advance
@bbbjim1fixedit4 жыл бұрын
it is not necessary, repair manuals tell you to do so to ensure no accidental start ups.
@engr.inigo.silva20007 ай бұрын
Mister, great video. But the matter in my F150 2001 is the sluggish acceleration at total stop. So, could it help to solve this matter cleaning that components according with the video?
@bbbjim1fixedit7 ай бұрын
you may wish to look closer at your vacuum hoses for leaks especially on the back side of the engine. I wish you the best on your repair
@engr.inigo.silva20007 ай бұрын
@@bbbjim1fixedit thank you, let check out this.
@luisponce1472 Жыл бұрын
Do you have to Disconnect the Battery before Installing The IAC valve?
@bbbjim1fixedit Жыл бұрын
I did not disconnect the battery. For lability reasons most shop manuals state to disconnect the battery. I wish you the best on your repair.
@locknload91432 жыл бұрын
What year? What side is it located? Also, can it be tested? Thanks
@bbbjim1fixedit2 жыл бұрын
This was done on a 2000 5.4L, it is located on the top of the engine near the fire wall. I am not aware of any tests for this part. I wish you the best on fixing your vehicle
@k.padraigokane14723 жыл бұрын
I have a 2000 manual. when I push the clutch in, the rpm will stay up. My mechanic unplugged the IAC and that issue went away. Of course it bog out a wee bit at idle, but the racing RPM issue went bye-bye. He said, "bad IAC, or bad computer." Think he's right?
@bbbjim1fixedit3 жыл бұрын
It is hard to say since one would need a rather sophisticated scan tool to pin point the issue. Removing the IAC and cleaning it is rather inexpensive and may well be worth a try. I wish you the best on your repair.
@travisburt2322 Жыл бұрын
I tried it. Didn't work. Replaced it. Nothing. Still idles choppy. Any other options?
@albertdelaney6814 Жыл бұрын
@@travisburt2322 did you find the problem , I have a 1999 f150 , and has a mind of it's own , normal idle rpm is 600 but at different times it jumps up high rpn ,
@kennyherrick8379 Жыл бұрын
Is there 2 IAC on a 98 f150? What is the one on fire wall above brake booster
@bbbjim1fixedit Жыл бұрын
I am only aware of the one IAC. I no longer have the truck and I am unsure of the one by the booster. I wish you the best on your repair.
@kennyherrick8379 Жыл бұрын
@bbbjim1fixedit it is the iac purge valve. The hose that comes off that part and runs to the back of the top part of motor. It has a Crack in it the size of around 2 inches. I rigged it it seem to keep it from sounding like it's going to die. Now it's figuring out what it's called. It has a green tip thing at the end
@bbbjim1fixedit Жыл бұрын
you may wish to do a Google image search with a picture, that has helped me out in the past. Thanks for the update@@kennyherrick8379
@kennyherrick8379 Жыл бұрын
@@bbbjim1fixedit and thank you as well for the response. Have a blessed evening
@reneramirez89223 жыл бұрын
I have a 2001 ford f150 5.4 only at cold starts the rpms drop then comes back up again. No check engine light, no codes. First I cleaned the throttle body with new seal gasket the issue went away. After a few months it came back and I cleaned the idle air control valve put it back on and also went away. A few weeks after it did it again any help on what could it be ti get it fix thank you.
@roxannekopecky13532 жыл бұрын
Any luck?
@reneramirez89222 жыл бұрын
I replaced the IAC and after that it turns on just fine.
@porterbennett70413 жыл бұрын
I have a question did your truck feal ruff when at normal temp Like did it feal like it had a ruff cylinder or no?
@bbbjim1fixedit3 жыл бұрын
It was only erratic when stopped, I didn't notice it when driving. I wish you the best on your repair
@williamisabell95394 жыл бұрын
Funny my ABS is out too.
@waynebastianelli83912 жыл бұрын
On that asap same as mine big difference thanks
@bbbjim1fixedit2 жыл бұрын
glad to help
@keeks2freakssseqz2294 жыл бұрын
Question: do you have to disconnect the power ?
@bbbjim1fixedit4 жыл бұрын
The electrical connector has a locking feature, I can't remember if it is the style you push down on while pulling off or the type you lift the tab up while pulling off. I do wish you the best on your repair
@pinacate8975 Жыл бұрын
What is the normal RPM in park position MY TRUCK IS A LITTLE BIT OVER 500 RPM.
@bbbjim1fixedit Жыл бұрын
depending on the temperature 500-700 rpms is normal
@pinacate8975 Жыл бұрын
@@bbbjim1fixedit thank you so much....is always in the middle
@reneramirez89223 жыл бұрын
I was thinking of just replace the idle air control valve since I left the same one on again. O'Reilly told me that it could be the throttle position sensor. If anyone had this same issue and got it fixed let me know pleace .
@randyu86883 жыл бұрын
What was it?
@fsca723 жыл бұрын
iac only effects idle. A bad tps usually causes things like the throttle not to respond correctly when you press on it or one most common the engine will rev real high on its own in park or neutral.
@JDIZZY0242 жыл бұрын
My 05 f150 stx will rev on its own sometimes any suggestions?
@bbbjim1fixedit2 жыл бұрын
you may wish to check for some check engine codes, several things affect idle: cracked hoses having vacuum leaks, MAF sensor, EGR issues, I wish you the best on finding your issue
@MegaErick20073 жыл бұрын
Could be many other problems, but this also an other one the MAf sensor
@bbbjim1fixedit3 жыл бұрын
thanks for the tip
@tonymctony45514 жыл бұрын
My engine revs up and down at the red light like im trying to race someone and bogs out if trying to accelerate. Runs smooth once u play with gas pedal up to speed.
@bbbjim1fixedit4 жыл бұрын
you may wish to take a close look at your vacuum hoses for leaks. I wish you the best in your repair
@tonymctony45514 жыл бұрын
@@bbbjim1fixedit do you think its o2 sensors? It runs clean, no smoke out of exhaust
@bbbjim1fixedit4 жыл бұрын
@@tonymctony4551 a faulty o2 sensor would trip a check engine code
@ianb1564 жыл бұрын
Did you figure out a solution for this tony?
@jarodbrown15293 жыл бұрын
@@ianb156 did you have the same issue? My 03 v6 does the same, my buddy says it could be the idle air control valve but I wasn't sure.
@stevendodge8144 жыл бұрын
When I bought this truck (2004 v6 manual f-150 xl) and he said something about a vacuum problem and the heat only runs through the defrost vents, do you think the iac is the problem? It isles between 790-1000 a lot
@bbbjim1fixedit4 жыл бұрын
what i believe he was talking about is the blend door actuator (changes the location of the heat). That not working would not affect the idle. If cleaning the IAC does not work try cleaning the MAF sensor, I have a video on that. I wish you the best on finding the idle issue
@Twilkins204 жыл бұрын
I could be a broken vacuum line too that happened on my truck thats what it was good luck
@Big_John_C4 жыл бұрын
There is a vacuum line under the throttle body that also connects to the PCV valve on your passenger side valve cover, the elbow that connects it to the throttle body dries and cracks causing a vacuum leak that makes the truck idle high and effects other things that require vacuum to operate...
@haydentrozzi2643 жыл бұрын
Is it the same for a 4.6L?
@bbbjim1fixedit3 жыл бұрын
I believe so, and I wish you the best on your repair
@jakefx42 жыл бұрын
the 4.6 is actually easier, it’s right on the top
@Angell-Angell Жыл бұрын
Looks like the helper did all the work to me!!..
@bbbjim1fixedit Жыл бұрын
she is awesome at turning wrenches, and I wish you the best on your repair
@tangleass Жыл бұрын
And you stay classy San Diego
@reygenabraham75644 жыл бұрын
I bought new one..but did not fix the problem
@PremiumFuelOnly4 жыл бұрын
@Reygen Abraham Probably a vacuum leak somewhere.
@dirtberger45334 жыл бұрын
Thank you so much. 😀🏁
@bbbjim1fixedit4 жыл бұрын
You're welcome!
@michaelvorgang27854 жыл бұрын
Q
@thefaith68914 жыл бұрын
Mine still vibrates what else could it be?
@JakeNaughtFromStateFarm4 жыл бұрын
Check for a vacuum leak. Maybe a loose or cracked hose.
@michaelbidwell42103 жыл бұрын
I started having a low idle issue then a vibration issue that came shortly after. I was really sure the 2 problems were related. It turns out my harmonic balancer was bad and completely separated a few days later. Unfortunately it put a huge hole in my timing chain cover. Not a good thing for sure
@rickytovar2263 жыл бұрын
Anyone had it stall n thoe wax the issue ?
@JoseyMcatee5 ай бұрын
Tryed this did not work long cleaning it made the problem wrost started humming after 2 time cleaning replace at parts house and i get a lifetime warranty.
@pauloremez2954Ай бұрын
Timing Chain Tensioners if Not leaky fuel injectors (Cylinder #5 probably)
@JuanLima053 жыл бұрын
Hi my f150 v8 triton. Has low and fluctuating idle but 1 click start.
@bbbjim1fixedit3 жыл бұрын
You may also wish to look for a vacuum leak on the intake hoses, if you have a check engine code for lean bank one or two. I wish you the best on your repair
@2_Sleazy Жыл бұрын
thank you
@bbbjim1fixedit Жыл бұрын
glad to help
@MarioLopez-ml8uw4 жыл бұрын
Thanks 👍
@bbbjim1fixedit4 жыл бұрын
Welcome 👍
@ingascheib88733 жыл бұрын
I have no idea where that is.
@bbbjim1fixedit3 жыл бұрын
top rear of the engine
@barbmalone4415 Жыл бұрын
I have replaced the cam shaft sensor and one next to it, throttle position sensor. Still does same thing, when you start it makes a knocking spinal noise. Give it gas goes away, if I am low idle it will start making the spinal knock noise til you give it gas in neutral. Anyone have any ideas. 2010 f150
@bbbjim1fixedit Жыл бұрын
you may wish to take a closer look at your vacuum hoses for leaks, especially if you have bank lean code. I wish you the best on your repair
@MrTootybooty Жыл бұрын
Did u ever fix ur problem mine is doing same thing