Damn, I'm in the process of installing a thermostat and decided to check out a video prior just because. I never knew about that little vent hole. I've played with it with my finger but never knew it should be facing up.
@elchanojose10 ай бұрын
Hello Scott! That component helps to get the air pockets out of the engine or as we call it burp air out. Also, this helps small amount of coolant to get by and always to have circulation through the cooling system and help or prevent static flow. Take well care Scott!
@terencescott395710 ай бұрын
@elchanojose4633 thanks for the info. I finished installing my new thermostat shortly after my last post. I went to check the positioning of the vent hole on my old thermostat. By luck I positioned it at the 11 o'clock position. Bit I'm good now. No leaks.
@sari-saritv.82357 ай бұрын
Thanks for this info
@twizted_josh2 күн бұрын
That's a super clean teggy
@jfcalix7 ай бұрын
The information what I was looking for thanks
@elchanojose7 ай бұрын
Hello! Thank you for taking your time to watch our video and for sharing that this was what you were looking for. Take well care!!
@GilbertMendez-j2s3 ай бұрын
Tab always goes to the top at its highest point 👍
@PlatinumtagАй бұрын
I usually drill a hole on the lil pin, did it on a dodge car and work perfect. Now i did it on a pontiac vibe and the car buble alot so i install the factory thermostat...
@elchanojoseАй бұрын
Hello! Thank you for watching our video and for sharing your experience and results. Take well care!
@merchanthandson52713 ай бұрын
Thank you for very important info. Can i make small hole to it same size?
@elroco48274 ай бұрын
It should be 12:00. The jiggle pin also helps bleed the vehicle
@Carpenter_King867 ай бұрын
Thanks homie
@anthonytrejo668 ай бұрын
So the little metal thing has to be open?
@elchanojose8 ай бұрын
Hello! The metal does not have to be open, it would be good and helpful to sit at the highest point when installation. Also, keep in mind that the thermostat be installed in the right way for it to operate properly. Take well care!
@TheShangralaaaa1710 ай бұрын
the jiggle pin faces upwards so the air can escape
@2STATIC_4LYFE2 ай бұрын
What happens if it's not? Does it cause the fluid to boil out of rad when trying to bleed
@mavadoroaster2 ай бұрын
Great info 👍
@elchanojose2 ай бұрын
Hello! I’m Hank you for taking your time to watch our video and hope this was helpful. Take well care!
@luisematos_8 ай бұрын
Great! 👍🏻
@elchanojose8 ай бұрын
Hello! Thank you for taking your time to watch our video and for sharing that it was great and you liked as well. Take well care!
@donaldwhiteman32247 ай бұрын
could this cause overheating? if installed with jiggle pin facing downward?
@towcars55507 ай бұрын
I think so I'm waiting on mine I bought one from AutoZone didn't have that lil jiggle...I got one from Amazon and it has it
@donaldwhiteman32247 ай бұрын
it was the cause of my overheating along with the coolant temp sensor. replaced no problems now! @@towcars5550
@PlatinumtagАй бұрын
@@donaldwhiteman3224 yes I think so bc on my vibe I bought a new thermostat and the original one was has the jiggle pin on 3 o clock position ,so I put a new one but was bubbling a lot bc I drill a hole on the jiggle pin...so I put back the original thermostat and I set it at 12 o clock and working well heard some Bubble coming out as it purge it own self.... Most of the time u have to see if fan is turning on time too....
@kenappel6149Ай бұрын
If you install the thermostat correctly the jiggle pin will be correct also, simple really
@midwest_nikk2682 Жыл бұрын
It does that no matter where the thermostat is located.
@lorddraako16554 ай бұрын
I bought a thermostat from AutoZone and it doesn’t have the jiggler pin should I install it?
@sergiocalderon5416 Жыл бұрын
Thank you dude I just changed mine a while ago🙏🏽
@elchanojose Жыл бұрын
Hello Sergio! Thank you for taking our video and hope this info is helpful for your next replacement. Take well care Sergio!
@CaratLV8 ай бұрын
i just bought a thermostat for my jeep compass but it didnt come with that silver piece in the hole???
@elchanojose8 ай бұрын
Hello! Some thermostats are not made the same. Some are made different but still work. The only advantage of that little silver valve is to allow air trapped to move by when the thermostat is close. This helps the engine to burp air out and fill the space with coolant. Take well care!
@RobertMorris-l3l6 ай бұрын
Tha k you for explaining the little thing that can be a fatal mistake
@MiguelOrtiz-kl1yb Жыл бұрын
Is it hard to install one ?? Just asking cuz I took mine to the shop and it’s been 2 days 😅😅
@elchanojose Жыл бұрын
Hello Miguel! A thermostat is not that hard to replace. Some cars require more labor than other but 2 or 3 days is too much time for this kind of job. The reason on why your car is taking too long for a thermostat replacement, is probably because the shop has other cars that are being worked on and your car is sitting there until a spot is available. Take well care Miguel!
@M.Qambar Жыл бұрын
It takes 2-3 hours at most if you don't know what you're doing
@gta4162 Жыл бұрын
@@M.Qambarbro. It takes like 20 minutes or less to replace a thermostat. On this type of car.
@M.Qambar Жыл бұрын
@gta4162 Yeah, that's true for me and you, but the original comment obviously doesn't know much about cars so it'll take them longer + i was talking about cars in general not just about this one because some would need a lot more work just to change a thermostat
@elroco48274 ай бұрын
It’s super easy. If you have the funds to pay the shop and you don’t feel like fooling with, then take it to the shop. But if you want to save money, do it yourself. I do a lot of maintenance myself. I’ve learned a lot by watching many KZbin videos.
@SimonLopez33125 ай бұрын
Hell yeah Brodie
@DFWAuto_Hack Жыл бұрын
Someone told me to break this off so my car does not overheat even if thermostat gets stuck closed. It was true. Car wants to overheat but cannot
@kevinhancock4064 Жыл бұрын
May I ask how you know it wants to overheat ? Ty
@Dcdc956 Жыл бұрын
Don’t do this… 🤦♂️🤦♂️🤦♂️🤦♂️🤦♂️ Jesus…
@DFWAuto_Hack Жыл бұрын
@@Dcdc956 lol i did and it worked
@AbelG8781 Жыл бұрын
@@Dcdc956only a dumb mfr would do something like that SMH
@OtherDalfite Жыл бұрын
@@Dcdc956all it does is bleed a bit of fluid over constantly. Not the end of the world
@chavatoyz6416 Жыл бұрын
That’s why I have a problem with my truck 😡 I installed it the wrong way!
@Thelost90910 ай бұрын
I just redid it on my jeep to find out I did it wrong to 😂
@2STATIC_4LYFE2 ай бұрын
@@Thelost909what happened when u did wrong, I'm trying to diagnose
@waltersmith316511 ай бұрын
Real mvp
@modelphotographyisart3456Ай бұрын
My thermostat doesn't have a little hole my friend
@elchanojoseАй бұрын
Hello! Not all thermostats are made the same. Some vehicles have been equipped with thermostats that don’t have the small hole or valve. If your thermostat is just full face metal with no hole, it’s ok and is going to work fine but just install it on the right orientation. Take well care!
@mindofmantae828810 ай бұрын
Thank you
@Travis-bs6hm11 ай бұрын
Thank you for your post
@kenstole46012 ай бұрын
It called as jiggle pin
@elchanojose2 ай бұрын
Hello! Thank you for sharing what it is called! Take well care!
@TaylorRamirez-uz9fw Жыл бұрын
Pregunta. El Ac De mi carro no está funcionando Sale caliente el aire y tiene coolant y el fan no está running
@user-xh2jz6jc4q Жыл бұрын
I don't understand how you can install it the wrong way. You can't install upside down, only a 180 maybe
@KKDriver Жыл бұрын
The thermostat I replaced on my civic literally wouldn’t fit unless the release tab was at the top. Pretty smart engineering.
@89gt5.02 ай бұрын
In short it’s a bypass.
@elchanojose2 ай бұрын
Hello! Yes, to let the air go by and keep fluid flowing. Take well care!
@alejaz840311 ай бұрын
Does it matter which way you Install it?
@wbforsure21048 ай бұрын
It does matter. The side with the coil spring always faces into the motor. If you install it backwards it will overheat
@elroco48274 ай бұрын
Probably not but I’d install it with the jiggly point facing upwards at 12:00
@Codeineworld5 ай бұрын
I need help from you
@durantplayz71112 ай бұрын
My stant one doesnt have any hole im so confused
@elchanojose2 ай бұрын
Hello! Not all thermostats are made like the one we showed on our video, some are made without the bypass valve that we talked about. If your thermostat doesn’t have it, don’t worry about that it is going to work fine. Take well care!
@Caleb-lbj Жыл бұрын
I drill it out sorry don't need it can drives better and faster
@elchanojose Жыл бұрын
Hello! There is nothing wrong about drilling it out. Makes sense on having a small hole to let small amount of liquid to go by. I don’t know about making it go faster but everything can be posible. Take well care!