Jabsco pump service and hull inspection

  Рет қаралды 78,550

Dangar Marine

Dangar Marine

4 жыл бұрын

In this video I pull the Jabsco raw water pump apart to figure out how it goes together and replace all the bits that need replacing. Normally in a service you will replace the oil lip seal, mechanical water seal and impeller. After that I go for a short SCUBA dive to check the position of the propeller relative to the rudder and cutlass bearing.
www.marineengine.com/parts/jab...
Flow monitor www.sbmar.com/product/complet...
If you are enjoying this channel, please consider making a donation to www.paypal.me/dangarstu or become a Patreon of Dangar Marine at / dangarmarine
T-shirts and other merchandise available at teespring.com/stores/dangar-m...
Common items used in these videos are available from my Amazon store at www.amazon.com/shop/dangarmarine
Dangar Marine is proudly sponsored by MarineEngine.com. MarineEngine.com supplies a wide variety of spare parts for many brands of outboard motors, be sure to check out their online store www.marineengine.com/
All music available at soundscloud.com/dangarstu

Пікірлер: 432
@DangarMarine
@DangarMarine 4 жыл бұрын
It's finally occurred to me (yes, I know I'm slow...) that I should add a pinned comment to videos to address certainly common comment and save myself a lot of typing. Main points from this one is that yes, if you aren't careful using the two screwdriver method to remove an impeller can dent the housing affecting it's seal. Personally I wouldn't lose any sleep over it if you are careful, but I have ordered an impeller puller anyway to be on the safe side and make the job easier to do once the pump is installed and I am replacing impellers on the water. The second point is that the nylock on the shaft was too tall for the nylon section to reach the thread. I just put some loctite on it for for now, I may find a shallower one down the track.
@geo-s-8530
@geo-s-8530 4 жыл бұрын
If you have a PP account Put a paypal.me link in the description Stu
@xsbuilder1
@xsbuilder1 4 жыл бұрын
Ahhhh, good! Another update. Thanks mate, I was starting to suffer symptoms of "Trawler Withdrawal". Never mind the ad hoc subject matter, when watched with a couple of beers, everything smooths out nicely.
@cybersylo5786
@cybersylo5786 4 жыл бұрын
Mate, don't worry about putting out a less than 5-star video every time. It is just good to see you plugging away on this project. Your explanations are more than they will find anywhere else for the items you are working on. Keep up the good work, you are doing great.
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks mate. There are a lot of jobs to do before this engine can be fired up and unfortunately none of them are particularly interesting.
@iamtheverybestever
@iamtheverybestever 4 жыл бұрын
Finishing with the chooks is perfect. Helps ease the sadness we feel when the video ends. Keep up the good work mate.
@DangarMarine
@DangarMarine 4 жыл бұрын
Glad you like them. :)
@retiredfederalie178
@retiredfederalie178 4 жыл бұрын
Zero degrees Stu, I love it!
@TheByard
@TheByard 4 жыл бұрын
I ran a pair of Ford Transit 2,5 lt diesels in my 1930s wooden 30ft boat, I had problems with the holding screw snapping on the impeller squash plate, repairs underway were difficult as the screw thread did not match anything in my bolt store until I found a screw in the electrical box. Next time in port I stocked up on the correct screws. The blessing of running twin engines is we kept going.
@DangarMarine
@DangarMarine 4 жыл бұрын
It's amazing how a single screw can bring a whole engine to its knees. Twin engines certainly do have their advantages!
@Graham19951
@Graham19951 4 жыл бұрын
Hi Stu I know you have the splined pump, but if someone watching has a keyed pump they must fit the rubber disc. Otherwise the key will travel along the keyway and cut a hole in the end plate. As I found to my cost 40 mile out.
@DangarMarine
@DangarMarine 4 жыл бұрын
Ah, that's good to know. I've really only got experience with outboard pumps so it's good to hear tips like that, thanks!
@adventure002006
@adventure002006 4 жыл бұрын
love the sound of the tropical birds in the background. We have had about 6ft of snow the last few weeks. Buried in snow for the next few months. Sure love to be in Australia right now :-).
@DangarMarine
@DangarMarine 4 жыл бұрын
Ah, the grass is always greener. When it’s hot here I wish I was in the snow!
@michaelmcclure8673
@michaelmcclure8673 4 жыл бұрын
Stu In the past, we've taken zip ties and put them around the impeller. So you can preload the direction. That way you can cut the with side cutters and pull out of the pump.
@DangarMarine
@DangarMarine 4 жыл бұрын
Nice idea!
@michaelsimpson9779
@michaelsimpson9779 4 жыл бұрын
In case someone hasn't already said, several manufacturers make fans for their 18V battery range of tools. They're surprisingly effective for what they are and a smidge of breeze on horribley humid days makes a world of difference. Amateur hour's ok by me, keep on keeping on.
@DangarMarine
@DangarMarine 4 жыл бұрын
Could be handy for sure.
@mikeelliott7535
@mikeelliott7535 4 жыл бұрын
Here's another tip for you Stu. I keep a big tube of KY on the boat. It makes a good impeller and rubber lube in water. I also use KY on the prop shafts when I move them in and out to protect the shaft seals. Try it on cutless bearings and I guess you'll find other uses for it also. Good luck.
@DangarMarine
@DangarMarine 4 жыл бұрын
It does some worth keeping some given that silicon grease is quite expensive in comparison and there are plenty of materials that don't like oil-based lube.
@N5XHIworkshop
@N5XHIworkshop 4 жыл бұрын
I have sold thousand of those impellers. We even made a white version to be used with milk products. The company I worked for was base in Dallas, Texas.
@RoadhogRNA
@RoadhogRNA 4 жыл бұрын
Great Vid Stu!!! Wow that gunk on the boat bottom is taking off!!! Once it starts moving hopefully some of that crud will come off!!!!
@MrKabDrivr
@MrKabDrivr 4 жыл бұрын
I find it hilarious that you have a poster of Zissou on the wall!
@JeffinLowerAlabama
@JeffinLowerAlabama 4 жыл бұрын
I see progress, Stu I'm always amazed by how fast stuff will grow on any none moving boats. Jeff in LA USA
@DangarMarine
@DangarMarine 4 жыл бұрын
For sure, although I'm also amazed how quickly 5 months has gone since it was launched!
@makeitwork583
@makeitwork583 4 жыл бұрын
Brupeg wants to launch before SV Seeker, but you’re going to beat them both. And Damon was making fun of the size of your boat... lol. Really looking forward to seeing you start sea trials!
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks Paul, I'm really looking forward to starting the sea trials too!
@paulg9314
@paulg9314 4 жыл бұрын
Well done Stu. You've rounded the home turn.
@Colin_Wait
@Colin_Wait 4 жыл бұрын
I suspect there could be enough demand for a D Squad KZbin channel. Keep up the good work and don’t worry about editing the underwater stuff shorter, we like it all
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks mate. I'm looking forward to doing a lot more underwater filming in clearer water. :)
@zetacon4
@zetacon4 4 жыл бұрын
Love the video clip of the birds. They are very pretty. So nice to see your feathered friends. Nice job on the rebuild of the pump too. Watching your underwater section reminds me of my days servicing of barnacle removal many years ago in very dark water while the boat was tied up at a slip. It was more done by feel than sight. Very dangerous job too trying to keep from getting cut on the extremely sharp barnacles.
@DangarMarine
@DangarMarine 4 жыл бұрын
For sure, so many diving jobs are done by feel in bad viz and barnacles certainly are sharp!
@-Viceroy-
@-Viceroy- 4 жыл бұрын
1 meter of snow in here, so what would be better to end the day than watching Stu sweat with an impeller. Btw. The birdie updates are the "cherry on top" of these videos. Keep em coming
@DangarMarine
@DangarMarine 4 жыл бұрын
Wow, that's a fair chunk of snow!
@tombauer5293
@tombauer5293 4 жыл бұрын
Great video. Three helpful hints for free. 1. Look at getting your next impeller from Globe. It’s made of blue silicone and lasts about 5 times longer. 2. Aligning the impeller ears is not really necessary. I had the pump end plate off to watch the impeller rotate rotate and noticed everytime I shut the Cummins off, it kicked back just a little. That was enough to flop the ears in the incorrect orientation. The ears realigned properly when I cranked the engine. 3. That brass cam plate or ramp is overlooked a lot. If that plate thickness wears by 25%, you loose 25% of your water flow. I didn’t realize how thin my cam plate was until I had a new one to compare it to. Mine was almost 30% gone. We have a lot of glacial silt around tidewater glaciers, and that must contribute to increased wear. The pump and cam plate had 5000 hours on them, but who checks the plate thickness?
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks for the tips!
@bartonrobinson4266
@bartonrobinson4266 4 жыл бұрын
Could ask for an easy job but what would be more fun, never done or viewed a few videos prior, it's a never ending push for easy and relaxing bits of work. Looked more complicated than my old chevy water pump. Did a pretty good job in my way of thinking !!
@DangarMarine
@DangarMarine 4 жыл бұрын
Car water pumps are nice and easy, you just replace the whole thing. :)
@JOHNJONES-qo3fh
@JOHNJONES-qo3fh 4 жыл бұрын
Nice rebuild on the pump mate very nice, great, interesting video, starting see a glimpse of light at the end of the tunnel.
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks mate. Every little bit that goes back on is one step closer to firing up!
@LeytonC
@LeytonC 4 жыл бұрын
Yes, I was speaking to the screen a bit when you were taking that pump apart :D but great Video! The back plate, the wedge and the front plate are designed to wear, we always called the front cover and back plates just 'wear plates' I have to admit I would change them just because it out and easy to get to, but they do last for years - I never changed mine again. I have seen people wreck a Jabsco pump using screwdrivers to lever out impellers, there is a proper puller for the job (Search jabsco impeller puller). The body of the pump is very pretty soft and if you mark / burr the gasket area and it wont seal the pump is dead. I know you have 'the feel' so you were going to be fine, but if its the first time you have ever touched one, use the puller - its will save you a fortune also make sure you have room to use it when installed, my boat you couldnt, so i bought some small plastic levers. Obvious being careful is the best bet!! One other to note, there is a gap between the PTO drive and the main pump body where you can see the shaft of the pump, if the seals are iffy or the shaft is worn water will drip from here and you can see it. (Also stops it running back in to the engine through the oil seal) Cannot wait to see the boat making way now, most of the fouling will just come off when it moving!
@DangarMarine
@DangarMarine 4 жыл бұрын
Interesting to hear about that puller. It is going to be much harder to get out once the pump is installed so that could be a good thing to keep with the spare impellers. I did notice that gap, it does make sense to not let water into the crank case if the seals both fail.
@seanbaldeschwiler1891
@seanbaldeschwiler1891 4 жыл бұрын
It's a good idea to have a spare pump on board. It's a bad day if it breaks. Scour ebay, scrapyard and Detroit forums for one. Great work. You're almost home. Dont forget to exercise and grease the valves, steering, strainers and other parts that have been installed but not in use. Nice work on the rose box by the packing gland too.
@DangarMarine
@DangarMarine 4 жыл бұрын
For sure, carrying spares is essential. Definitely have a bit of work to do on some of the bits that haven't been opened since the boat went in the water. Those seacocks are bound to have a bit of growth in them by now, not to mention the sonar transducers.
@rideswithscissors
@rideswithscissors 4 жыл бұрын
7:36 I am literally screaming "Stu, remove the cam!" We had one of these for a bilge pump, and ran it dry during hurricane David, had to clean burnt rubber out of the thing with the wind just howling and water filling the bilge, with both the 471 engine and Onan generator banging away. Nerve wracking! Abandoning ship in a rubber dinghy with 80 mph winds (127kph) would not have been good. Your videos flood me with great memories.
@DangarMarine
@DangarMarine 4 жыл бұрын
That does sound a bit stressful! I've seen a few bits of equipment fail during times like that as the pressure of the moment can very easily cause people to forget their usual routines like swapping valves over etc. Glad you survived okay!
@rideswithscissors
@rideswithscissors 4 жыл бұрын
@@DangarMarine We had some redundancy in our favor. Damned if I let everything I have go to the bottom of a lagoon while I get blown into the mangroves! A lot of carnage around us as we headed home, but you can't be smug when you see other people's dreams showing nothing but a mast or a Bimini top above the water. Captain Peter could be a bloody ass, but we will be friends forever 'cause of all the crap we went through together. Boat life will do that to you!
@BushPigADV
@BushPigADV 4 жыл бұрын
WOW! I'm amazed at the growth and how fast it came. Keep up the good work man, love your videos. Cheers from the coast of Maine.
@michaellacey7303
@michaellacey7303 4 жыл бұрын
WOOT, D-Squad for the win! Nice update Stu, look forward to seeing you beat the hell outta that drive shaft.
@DangarMarine
@DangarMarine 4 жыл бұрын
Yeah, it’s certainly going to be a battle that’s for sure!
@trixiegreatorex6676
@trixiegreatorex6676 4 жыл бұрын
I know you need to get in the water but drop the drone (rov) in for a look first, you know what your in for then. Great stuff mate.
@DangarMarine
@DangarMarine 4 жыл бұрын
Trixie Greatorex The trouble with the drone in murky water is that it is very easy to get lost and never find the bit you are looking for.
@navigator902
@navigator902 4 жыл бұрын
Installed a hundred red idiot lights almost every installation... keeps me from coming back in less than a year in most cases.... lucrative marine diesel mechanic. S.F.bay.
@ilarsson1
@ilarsson1 4 жыл бұрын
Keep up the good work that you do! I greatly appreciate being able to follow along on the journey.
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks mate. :)
@ThorbjrnPrytz
@ThorbjrnPrytz 4 жыл бұрын
love your temp conversion!
@johnlong5343
@johnlong5343 4 жыл бұрын
The sensor is a great idea for water flow. Love the dive video can’t wait for some wreck diving!!!
@davidwoods4366
@davidwoods4366 4 жыл бұрын
Thanks as usual Stu, glad you saved tthe pigeons till last,take care
@DangarMarine
@DangarMarine 4 жыл бұрын
I know what you’re thinking, save the best for last!
@jeremynewhouse6530
@jeremynewhouse6530 4 жыл бұрын
I don’t understand why someone would dislike this video. He isn’t doing brain surgery and half a$$ing things. It’s a water pump and he just uses the tools he has at his disposal. I don’t know it just doesn’t make sense to me, maybe one of the 9 people who did can enlighten the rest of us.
@gavinb9627
@gavinb9627 4 жыл бұрын
Maybe coz no chickens were harmed in this video?
@martinpiggins5772
@martinpiggins5772 4 жыл бұрын
Good stuff Stuey, nice to something going easy for a change, although couldn’t believe the grime under the water line and after all that hard work. Looking forward to the next one 👍🏴󠁧󠁢󠁥󠁮󠁧󠁿
@johnkinnane547
@johnkinnane547 4 жыл бұрын
Good job Stu, it was good how you just went ahead with it even though you didn’t know that much about it but you figured it out and learnt a few things while doing it. Good one Stu kind regards John
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks John. I find when you look at most things they are a familiar set of components. Oil seals, bearings, drive shafts etc.
@glastronjohn1
@glastronjohn1 4 жыл бұрын
Nice job. Dig your channel. I've spent 20 years building space rockets/aircraft at Lockheed. Your stuff is much more enjoyable. Joined your Patreon.
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks mate! :)
@Dan_C604
@Dan_C604 4 жыл бұрын
Stu, thank you so much for this episode. I learned a lot about jabsco pumps. It was nice to see you working this through step by step. That pump looks great. Also, thank you for keeping your patrons and followers updated with honesty, not like others playing stunts and humiliating followers. Great episode!!
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks Dan, glad you liked it. I'm glad too to know a bit more about these pumps now. They are certainly something that every owner should be familiar with even if you get a mechanic to do the bulk of the mechanical work.
@mhn3773
@mhn3773 4 жыл бұрын
Stu, I enjoyed the video like always. I have never felt let down by any video you have produced. I feel fortunate that I can experience these things with you. I am always excited for new videos, I wonder what you will be up to now. Thanks Stu!
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks mate, glad you liked it. :)
@richardbohlingsr3490
@richardbohlingsr3490 4 жыл бұрын
Smart idea adding the raw water sensor to the pump circuit. Lot of growth on the hull just sitting on the mooring. Good job sharing the pump rebuild. Might be a good idea to keep an extra rebuild kit on board. Coming along nicely.
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks mate. For sure, definitely always carry a spare rebuild kit onboard when cruising.
@grottyboots
@grottyboots 4 жыл бұрын
Another excellent video, Stu! I love listening to you work through your problems. One of the first KZbin video I watched was how to fix an impeller on a old small outboard. It convinced me I could do the same on my 80's Evinrude 7.5HP. Cheers!
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks mate. Most of this stuff can be understood from first principles with a bit of time. There are still things I would get a pro to do (like maybe aligning the engine) but impellers are definitely DIY territory.
@grottyboots
@grottyboots 4 жыл бұрын
@@DangarMarine Lots of stuff is DIY once you've seen a video of someone else doing it. Knowing the proper tools, hearing the calm, reasoned voice of an expert reasoning through the process is gold. Also, 2 thumbs up to the pinned comment you added here! I find most KZbin comments not worth the effort, so surfacing your additional thoughts is, again, GOLD! Please do more of that...
@cw3339
@cw3339 4 жыл бұрын
Happy Monday Stu
@jeff3238
@jeff3238 4 жыл бұрын
No chickens were harmed in the making of this video, though some complained they were made to feel silly.
@otm646
@otm646 4 жыл бұрын
I always lube the pump with a heavy dose of 50/50 dish soap and water. Makes assembly much easier. Far more lube than that little packet they give. First time is always a pain, you did a solid job.
@DangarMarine
@DangarMarine 4 жыл бұрын
Yes, a fair soaking would certainly make it a bit easier.
@royboydanny1415
@royboydanny1415 4 жыл бұрын
Because the nylon can melt with the fast speed of the air tool. The speed of gun creates friction, it's best to use a spanner. Great work you're doing on the boat. 👍🇬🇧
@DangarMarine
@DangarMarine 4 жыл бұрын
It is amazing how much heat can be generated just doing and undoing nuts and bolts.
@chrisskelhorn5727
@chrisskelhorn5727 4 жыл бұрын
Good to see the D squad! And I was part of the '2 grunts with a big spanner' brigade, so I understand your torque wrench settings! :-) As the nearest I get to deep water is driving over a bridge, I'm watching with interest! :-)
@DangarMarine
@DangarMarine 4 жыл бұрын
I like the idea of measuring torque in "grunts" ;)
@dinacaldwell7522
@dinacaldwell7522 4 жыл бұрын
I have been waiting for a dive shot since you started the refit on this boat
@paulmalonemolly
@paulmalonemolly 4 жыл бұрын
Hey mate, whenever I'm putting an impeller in I put 2 cable ties around it to compress the vanes, then as it goes in cut them off one at a time. Also Ive found its not really necessary to be super critical about which way the vanes are pointing cause once it rotates they will all pop to the right direction! Obviously if the pumps connected to the engine you cant turn the impeller so its a pain in the arse to get the things in for sure!!
@rogerbayzand4455
@rogerbayzand4455 4 жыл бұрын
Beat me to it that's exactly what I do.
@marcjordan29
@marcjordan29 4 жыл бұрын
I can't love this channel any more! I can't wait for the fire up..... Nothing like it
@DangarMarine
@DangarMarine 4 жыл бұрын
marc jordan I feel sorry for you. :(
@marcjordan29
@marcjordan29 4 жыл бұрын
@@DangarMarine hows that?
@marcjordan29
@marcjordan29 4 жыл бұрын
@@DangarMarine wait..... I mean i cnat love this channel..... Any more than i already do.....
@marcjordan29
@marcjordan29 4 жыл бұрын
@@DangarMarine grrr... Suxks that text can be read not in the manner i wrote it..... ... To be clear... I LOVE THIS CHANNEL! you are my Australian hero.... You and life onnthe hulls
@duncanjames914
@duncanjames914 4 жыл бұрын
We call your circlip clips- "Oh-Shit" washers (technically c-clips here also), cause they always spring off into the unknown and are followed by me saying - "Oh shit!"
@nanocofocclo440
@nanocofocclo440 4 жыл бұрын
If at first you dont succeed........ use a crow bar, excellent! You go Stu!! Great vids.
@CheersWarren
@CheersWarren 4 жыл бұрын
That was fun! I think the diving was the best! My impellers come with the same little packet of start up grease but it's labeled Glycerine...... cheers Warren
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks mate. Plenty more interesting diving to come once the boat is up and running.
@Jay-ln1co
@Jay-ln1co 4 жыл бұрын
Reminds me putting together my new PC (from mostly used parts). A learning experience after 11 years since my last build. Went through 3 motherboards because the one I got with the old PC I was salvaging was proprietary and didn't work with my power supply. The second just needed some adapters for cables, but apparently now you can have a socket that fits processors the motherboard doesn't support. Neat! Third time's a charm. Then just had to cram it all into the small case. And the front panel cable is not fully seated because the USB3 socket is too close.
@DangarMarine
@DangarMarine 4 жыл бұрын
Ah, it's all a learning experience!
@gavinb9627
@gavinb9627 4 жыл бұрын
Murphy visited you too
@shaneharrison4775
@shaneharrison4775 4 жыл бұрын
Nicely done Stu
@robpbandit
@robpbandit 4 жыл бұрын
Love it just watching “exploring abandoned mines” and as it finished stu popped up! 😉
@DangarMarine
@DangarMarine 4 жыл бұрын
That sounds like the type of channel I would like. :)
@robpbandit
@robpbandit 4 жыл бұрын
Dangar Marine kzbin.info/www/bejne/jXqZcqOLq9qHpa8 Look at some of his other videos! You’ve got to have a big pair of balls to wanna decent down some of those shafts and do what he does. Make my arse twitch just watching 🤣😆
@-Viceroy-
@-Viceroy- 4 жыл бұрын
Frank found pretty old jeans
@jossmaxwell00
@jossmaxwell00 4 жыл бұрын
Well I am a fan of that channel too Robert. And like you up popped Stu;s vlog. Insomnia rules.
@gavinb9627
@gavinb9627 4 жыл бұрын
@@jossmaxwell00 Not that we would ever say Stu's videos cure insomnia, they certainly help pass the time very well
@robwooly
@robwooly 2 жыл бұрын
Your a champion, you've been so so helpful , thanks for educating us, great KUDOS to you, have a great festive season, be well. Rob
@briananderson3620
@briananderson3620 4 жыл бұрын
Love the " won't come undone newton meters" torque specs
@annbullock7622
@annbullock7622 4 жыл бұрын
Jeez it's cold here mate, 15 deg well in Ireland that'll be a good sunny day.
@jizzypimp123
@jizzypimp123 4 жыл бұрын
I wouldn’t be offended if you showed more of the chickens, i honestly wouldnt mind! ;) ha
@harrygreene8669
@harrygreene8669 4 жыл бұрын
Chicken Marine should be your second channel.
@handsonwithblg4949
@handsonwithblg4949 4 жыл бұрын
Looks like cutting in a small air conditioner to the wheel house may be on the list in the future . Beers ! I tip my can to you Sir ! Thank you for your work showing us this great adventure .
@DangarMarine
@DangarMarine 4 жыл бұрын
Have been toying with the idea of AC.
@tommadigan1783
@tommadigan1783 4 жыл бұрын
Stu - Great as usual...I can't wait for you to make smoke
@donjohnson5307
@donjohnson5307 4 жыл бұрын
Great vid, ok you take a zip tie wrap it around the impeller towards the top end so it will pull off easy in the direction u want to be.drop it in the housing when it home u pull the zip tie off makes a 10 min job in to a 1min job easy
@stjohnjourdan9444
@stjohnjourdan9444 4 жыл бұрын
Hey Don, good idea - will try same when I next do my water pump. cheers
@finscreenname
@finscreenname 4 жыл бұрын
Next time Stu put a little grease on the gaskets. That's what V drive builders do so the gasket will seal but not stick to it.
@youmeandtheD
@youmeandtheD 4 жыл бұрын
To clean the bottom get a stainless steel drywall knife as wide as you can find. We have a 6ft cut away keel, put a weight belt on and swim lengths of the hull. Also most of that crap will come off when you get moving.
@stevepaterson2617
@stevepaterson2617 4 жыл бұрын
Love the chickens.lol Glad to see i'm not the only one that talks to birds
@DangarMarine
@DangarMarine 4 жыл бұрын
They certainly talk back enough!
@gavinb9627
@gavinb9627 4 жыл бұрын
@@DangarMarine Happy chooks lay more eggs
@ruperthartop7202
@ruperthartop7202 4 жыл бұрын
Great video Stu. Like the dive cam. Cheers
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks Rupert. :)
@georgelewis8904
@georgelewis8904 4 жыл бұрын
Thanks for the video, surprised by how soon the growth happened, just doesn't seem that Long been in the water, like sounds of water on the hull as you were working.
@andrewtaylor9615
@andrewtaylor9615 4 жыл бұрын
Another great video Stu. Way better than most of mine...
@edac1078
@edac1078 4 жыл бұрын
" won't come undone again newton meters", I gotta remember that one!
@rogerdeves1511
@rogerdeves1511 4 жыл бұрын
Good job mate time for a quick Coopers!
@sstem2169
@sstem2169 4 жыл бұрын
I really enjoyed the pump rebuild and will likely refer back to this episode at some future date for DIY encouragement. I really enjoy your chicken vids at the end! It's amazing the personalities that chickens can have. It's been a joy getting to know yours!!! (yes, I'm a fellow bird nut....) ;-D
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks mate. Yes, chickens do have very different and distinct personalities for sure. :)
@torepres
@torepres 4 жыл бұрын
I love to follow the way you are fixing the trawler. Big job and intreresting to follow your work on th boat, without shorcuts. Regards Tore, from Norway
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks Tore. :)
@pdgearhead3504
@pdgearhead3504 4 жыл бұрын
Stu, I used to pour water down the exit hose on rebuilt raw water pumps just before the first start up in addition to lubricating the impeller. It was probably not really necessary, but it seemed to help. Great work - looking forward to to seeing you under weigh.
@DangarMarine
@DangarMarine 4 жыл бұрын
Yes, I was thinking something similar to help with lubrication and priming the pump.
@pdgearhead3504
@pdgearhead3504 4 жыл бұрын
I also left the discharge hose off of the pump just to allow the pump to prime without any possible back pressure - again, probably not necessary but at least I knew the pump was working as it pumped some water out of the pump. I was always paranoid of running the pump dry.
@cliffstevenson5773
@cliffstevenson5773 4 жыл бұрын
I am amazed to see the marine growth since launch - five or six months? Another very interesting video about ...a water pump? Every time you say something like "monitor while the boat is underway" I get a little thrill of anticipation - I am already exited to tag along on your first voyage.
@woppaenginerring
@woppaenginerring 4 жыл бұрын
I Love Stu's everything is a hassle attitude.
@DangarMarine
@DangarMarine 4 жыл бұрын
I wouldn't have that attitude if everything wasn't a hassle. ;)
@StonyRC
@StonyRC 4 жыл бұрын
Tighten them to "Won't come undone again" Newton/Metres ... that kept me chuckling for ages!
@johnduffy7502
@johnduffy7502 4 жыл бұрын
Very interesting video! I've worked on a couple of small Jabsco Pumps, I remember the impeller vanes but not the details. An informative sequence though. Quote: "Swapping to Dive Cam" :) awesome. I couldn't get over how much growth there is on the hull and prop. Still I am more used to ships where we had ablative anti-fouling on the hull and you might get the odd barnacle in the bow thruster tunnels. For the prop we were more concerned with cavitation damage than weed! But then, a day in port was a day wasted. Looking forward to the shaft alignment - hope you are not tackling this on your own!
@DangarMarine
@DangarMarine 4 жыл бұрын
Hi John. I think that dive was a bit deceptive with regards to the condition of the entire hull but I'll do a longer video of that once I get some gloves and a scraper. For sure I'll need to clean out the skin fittings and sonar transducers though. Unfortunately the alignment has been mostly a solo effort so far, although I did grab Dave to help me get the new shims under the engine mounts a few days ago. I'm still at a bit of a loss as to how I'm actually going to do it at the moment but I'm sure I'll get there in the end.
@DonBehrens65
@DonBehrens65 4 жыл бұрын
"won't come undone newton meters" killing me :)
@ThePaulv12
@ThePaulv12 4 жыл бұрын
I thoroughly enjoy your poultry intercouse at video's end - a fitting climax.
@McTroyd
@McTroyd 4 жыл бұрын
"Never-coming-off-again newton/meters." I think I can handle that metric conversion... it's close to "I-lost-my-torque-wrench ft/lbs," right?? Amazing how often that measure gets used.
@DangarMarine
@DangarMarine 4 жыл бұрын
Pretty much. ;)
@townsville69
@townsville69 4 жыл бұрын
Free range eggs on toast with a nice cuppa is pretty hard to beat.
@DangarMarine
@DangarMarine 4 жыл бұрын
Sure is!
@DanielJLopes
@DanielJLopes 4 жыл бұрын
Thank you for the video! The Renko! It's alive!! ^_^
@25hpboatracerman
@25hpboatracerman 4 жыл бұрын
Your a champ! Love your vids mate 👍
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks mate.
@douglasjohnson8820
@douglasjohnson8820 4 жыл бұрын
You don't have to put Loctite on the four small bolts holding the cover on. I have been putting Mercury 2-4-C on them for years and they always come out easy when I replace the impellors every spring on my twin engines.{ They always come out of the pump with a "set" after sitting idle while up on the hard for the winter} Also use the 4 small washers that come with the bolts. Really enjoy watching your videos.
@robinszemeti3085
@robinszemeti3085 4 жыл бұрын
Now then Stu, whenever you take out those bronze cam plates "that allow the pump to pump" ... always note which way around they go, as often they have a slightly different profile ... and it is dependent on which way around the pump is rotating, and if you get it backwards it will run, but cut up the impeller real quick. The "input" side has a slightly shallower profile than the outlet usually, to give the rubber blades an easier start. Not sure about the Jabsco ones, but the Volvo Penta ones are "handed" and it chews up fast if you get it wrong, don't ask me how I know.
@DangarMarine
@DangarMarine 4 жыл бұрын
Good tip. Given that, If I was making them I would slightly offset the bolt hole so it can’t go in the wrong way.
@TheJustonemore
@TheJustonemore 4 жыл бұрын
Great video
@jackpatteeuw9244
@jackpatteeuw9244 4 жыл бұрын
At 2:33, the 2 small holes are so you can tap them and insert long bolts up to the puller cross arm ! When circlips are extremely corroded, scrape off as much of the corrosion possible, hit it with some penetrating oil and use a screw driver/pin punch to get the circlip moving in the groove. That is half of the battle. I hope you bought 2 carb kits for the Honda engine and you still have a spare kit for the Jabsco pump.
@DangarMarine
@DangarMarine 4 жыл бұрын
Good tips!
@MsJon52
@MsJon52 4 жыл бұрын
good vid as usual, just a thought, remembering when i had the good fortune to work on the stern gear , joke, if you need a couple more inches to push the shaft out turn your rudder fully to one side or the other this will give the prop a couple more inches of travel, i am probably stating the obvious but it just brought back the memory, anyhoo your nearly there now, just the electric bow thruster and hydraulics to be fitted to your hoist and you will be away lol
@DangarMarine
@DangarMarine 4 жыл бұрын
Good tip on turning the rudder.
@googleplusisdead
@googleplusisdead 4 жыл бұрын
I'm a bit amazed that the connection from engine to prop shaft is a solid one, vs. some sort of even slightly flexible coupling, U joint, hard man-made rubber insert between crank and shaft. Please remind me the year that boat was built as well, perhaps newer setups have such connections which would also allow for some sort of shock/vibration absorbing motor mounts.
@DangarMarine
@DangarMarine 4 жыл бұрын
I’m adding a poly flex coupling but it was originally metal on metal. Not enough room for a CV joint. Owner built in 1990.
@duncanjames914
@duncanjames914 4 жыл бұрын
I've already given you a thumbs up as I know your video presentation will be excellent! :-)
@DangarMarine
@DangarMarine 4 жыл бұрын
Thanks mate!
@AlisonFort
@AlisonFort 4 жыл бұрын
D-squad on manoeuvres - great!
@EricLRyder
@EricLRyder 4 жыл бұрын
0 degrees Stu..... Love it.
@SkypowerwithKarl
@SkypowerwithKarl 4 жыл бұрын
I’m glad you used the supplied lubricant. That happens to be silicone grease. If you have an impeller and no lube, you can usually get the stuff at a dive shop if you don’t have time to order it. Never use petroleum based, or marine grease on the paddles because it can cause the rubber to swell up or soften. Dish soap is ok, but less than optimal. I hope that wasn’t fresh red Loctite you used or the next change will get a bit wordy. I use tiny dab of blue Loctite a lot on things, it’s as good as a new lock washer. Never allow Loctite or white pipe sealant to contact plastic as it can cause it to become brittle. Humm, so that’s why that air pressure regulator cracked?
@gavinb9627
@gavinb9627 4 жыл бұрын
It was 569 hydraulic sealant not 262/3 stud lock so there won't be a drama undoing them
@russellmartin2705
@russellmartin2705 4 жыл бұрын
Swimming pool supply store is cheaper and larger tubes
@SkypowerwithKarl
@SkypowerwithKarl 4 жыл бұрын
Russell Martin Good to know. Three choices Amazon, pool supply and dive shop for silicone grease.
@russw5301
@russw5301 4 жыл бұрын
Just a thought, I have seen a few of the Bribie locals with boats moored in the canals here slip over the side and under the boats with the Gerni in hand and do an underwater pressure clean. Seems to work pretty well. Love your work mate, bit surprised to not see a "Coopers" in this episode? Don't dehydrate.
@DangarMarine
@DangarMarine 4 жыл бұрын
Interesting. I would have thought the water would have lost speed pretty quickly. I'll give it a try if people have success with it.
@russw5301
@russw5301 4 жыл бұрын
@@DangarMarine Yes, they hold the nozzle reasonably close to the hull it gets a lot of crap off. I have done it in my pool with success. Its worth a go. If it fails I will bring down a carton of Coopers next time I go to Urunga. I will venture further to Dangarville.
@joecucch8261
@joecucch8261 4 жыл бұрын
Impact driver is one of the most important tools in the box. you can also use it to make sure those bolts are tight.
@DangarMarine
@DangarMarine 4 жыл бұрын
They sure are handy!
@artmallory970
@artmallory970 4 жыл бұрын
'Wont come undone again newton meters...' Sounds like 'John Deer tractor tight'
@jimh.5286
@jimh.5286 4 жыл бұрын
Since you lacked a dive buddy, I watched the video very carefully and would have called the authorities right away if you failed to return from the water.
@DangarMarine
@DangarMarine 4 жыл бұрын
LOL. Thanks mate!
@maddoc68
@maddoc68 4 жыл бұрын
The clock is running!!!!!!! 😃
Making and installing new engine shims
36:00
Dangar Marine
Рет қаралды 79 М.
Measuring a propeller and applying Propspeed
19:02
Dangar Marine
Рет қаралды 74 М.
When You Get Ran Over By A Car...
00:15
Jojo Sim
Рет қаралды 29 МЛН
Became invisible for one day!  #funny #wednesday #memes
00:25
Watch Me
Рет қаралды 58 МЛН
Raw Water Pump Replacement : Perkins 4108
8:22
SBCODE
Рет қаралды 5 М.
EXPERTS ACTUALLY SAVED Rick Harrison From Losing Everything
18:18
Trend Set
Рет қаралды 2,1 МЛН
Ep 124 | New Impeller and Jabsco Raw Pump Fix, Sailing Pacific Mexico
17:21
Life in a Nutshell
Рет қаралды 11 М.
How to rebuild a marine raw water cooling pump in the field without a workshop.
16:06
Alternator installation and fuel supply fix
39:47
Dangar Marine
Рет қаралды 94 М.
Jabsco 50410-1251 Raw Water Pump Re-Assembly
17:33
MrBob’s Wonders
Рет қаралды 55 М.
How to fix a leaking salt water pump
15:10
spelunkerd
Рет қаралды 43 М.
Джеки Чан лишил наследства всех своих детей! Что акажете?
0:41
Симуляция: МАТРИЦА МИРА
Рет қаралды 9 МЛН
Кот Оказался В ЗАПАДНЕ🙀☠️
0:38
ИССЛЕДОВАТЕЛЬ
Рет қаралды 5 МЛН
The FAST and FURIOUS Table Hack 😱
0:29
LosWagners ENG
Рет қаралды 3,9 МЛН
BABY Comedy : Birthday Baby and Kind Man ❤️
0:36
BABY Comedy
Рет қаралды 15 МЛН
腹黑小天使把黑天使整惨了#short #angel #clown
0:20
Super Beauty team
Рет қаралды 43 МЛН