Hello I have a Smitch industrial sewing machine, my thread keeps breaking. Is frustrating please help
@Cyrilmc2220045 жыл бұрын
Thank you so much. Very helpful and useful.
@Sewinggold Жыл бұрын
You are most welcome.
@zurizaharalove83225 жыл бұрын
My dial for my main shaft won’t move to maintain the needle in motion. How do I free it from being locked up? It won’t turn the dial at all either direction. Help.
@ktkatina92 жыл бұрын
How can I gather fabric on juki 8700 without gathering foot
@TheDodoVox3 жыл бұрын
Why does my Juki 5550 gather just on reverse stitches?
@jasonclark5584 жыл бұрын
Alright so I am more of a Consew 206 person but recently have been working with the Juki. To the problem when the needle is out it seems to have a good spi but when the needle gets installed it goes to max spi. Any sugestions?
@Sewinggold4 жыл бұрын
I'm not quite clear on what you are asking. SPI to me is stitches per inch. Can you rephrase? Thank you.
@jasonclark5584 жыл бұрын
@@Sewinggold Yes so with no needle in it seems to feed fine. When needle is installed it has a spi of 30.
@thuhua91734 жыл бұрын
Hi SewingGold. I’m having an issue that I haven’t not been able to figure out. Would love your advice. The needle is stuck in the down position. I can’t seem to retract it to change needle nor the under thread. Any insight on what’s wrong? Thank you for your time.
@Sewinggold4 жыл бұрын
Loosen the needle set screw and push the needle down as far as you can. It should come out of the needle bar enough to remove it. If you machine is locked, check to see if there is thread in the hook assembly, and then follow one of our "jam fix" videos.
@thuhua91734 жыл бұрын
SewingGold.com we watched your jam fix video, and we are tried the last option which was remove the 3 small screws, we can’t get the the 3rd one because the wheel won’t move.
@Sewinggold4 жыл бұрын
@@thuhua9173 Remove the position finger and then you will be able to rotate the hook to access that screw.
@thuhua91734 жыл бұрын
SewingGold.com I realized I miss a key point. The machine has been sitting for years. Does that make a difference on what needs to be done? It was working perfectly fine before it sat.
@diywithcharlie30185 жыл бұрын
Having problems with gathering - I have followed your suggestions but still can’t fix my issue. I’m quite new to industrial juki. Do you have an email that I can send photos of my issues to you for some help? Would be greatly appreciated
@Sewinggold5 жыл бұрын
info@sewinggold.com
@lalanaw95345 жыл бұрын
I have a Juki DDL-8700-7 how do i adjust to sew thinner materials like silk without the stitches being and looking so loose?
@kristysanden425 Жыл бұрын
Hi! I’m having issues with my machine, the computer part of the machine won’t back stitch. I’ve been trying everything I can think of.. can you help?
@Sewinggold Жыл бұрын
What model is the machine?
@kristysanden425 Жыл бұрын
@@Sewinggold I have a Juki DDL 8700-7 with the CP 18 attached to it. Whenever I try to backstitch using the lever next to the needle, it is completely stuck.
@checkyamber30354 жыл бұрын
I have ddl 8500, the needle was stuck because the rotator was spun by kid. How can i fix it?
@Sewinggold4 жыл бұрын
I am not familiar with rotator. Do you mean the hook assembly? If the needle is jammed in the hook, you can use this video as a guide. It is a different machine, but the same principles. kzbin.info/www/bejne/bIGqgaehn9ikq9U
@alexisjones61034 жыл бұрын
Hello My juki machine is running nonstop once turned on. Do you know what it could be or what i could do to fix it?
@darknessfierce42097 ай бұрын
That sounds like an old motor before they changed types The older motors would run when the machine was on whether or not you were using it
@ToyoZiv3 жыл бұрын
I just assembled my new Juki DDL 8700 and sew for the first time. My new machine sews backwards. Please help!
@Sewinggold3 жыл бұрын
Check the rotational switch on your motor. The machine should be set to run counter clockwise.
@dianeschildgen67944 жыл бұрын
The bobbin is spitting out lots of loops on the bottom of the material. Help?
@Sewinggold4 жыл бұрын
Without seeing the machine I cannot give you a definitive answer, but these two videos are a good place to start. They are on "tension." kzbin.info/www/bejne/sJfOYZinidmKh6s kzbin.info/www/bejne/eXO1pKSFn7usr5I
@darknessfierce42097 ай бұрын
If it’s on the bottom of the material, need to re-thread the top of the machine Switch your Bobbin color or your top color so you can see which one is causing the problem
@evansappiah96653 жыл бұрын
My juki wachine is sewing backwards instead forward but moves forward when i press for backwards
@Sewinggold3 жыл бұрын
The problem is more then likely your motor. You may have a switch on your motor to change the rotation of the pulley. The balance wheel and pulley on the motor should be running counter clockwise.
@seyjun25414 жыл бұрын
Jose And Steve please help me!
@ukristo3 ай бұрын
My machine is not working please show me what to do please
@tmo17325 жыл бұрын
My juki machine is skipping stitches and sometimes won't even sew at all
@Sewinggold5 жыл бұрын
There are a few things that can cause skipping. The most basic is the needle in backwards or not all the way up in the needle bar. If you are using a Juki DDL-8700, make sure the needles are DBx1 or 16x257. Mechanically, it could be the timing. You can try and fix that yourself, but hiring a good sewing machine mechanic may be best. Good luck!