Kawasaki Nomad Oil Leak Repair - Clutch Shaft Seal Replacement

  Рет қаралды 14,895

Lehew

Lehew

Күн бұрын

Пікірлер: 48
@rayezell4989
@rayezell4989 7 ай бұрын
I had a leak just as described in the video. I followed Lehew's instructions to the letter. When I removed the clutch slave housing, the seal was out of the housing and protruding on the rod just as he described. At that time, I did not have the replacement seal. So, I pressed the seal back into place as a temporary measure until my replacement seal arrived from Partzilla. So, about a week later, when the part arrived I went into the garage and installed the new seal. Reassembled the bike and went for a test drive. This is when stuff went South. During the test drive which didn't last very long, I discovered I had lost gears 2, 3, 4, and 5. I freaked out!!! Called a friend of mine, he asked me if I had bled the clutch after reinstalling the clutch slave housing? I said, no the video didn't mention anything about that. Long story short, he came over and showed me how to bleed the clutch. Problem solved and blood pressure back to normal. This is a great video. He just forgot to mention bleeding the clutch afterwards.
@LehewTech
@LehewTech 3 ай бұрын
I did not have to bleed the clutch after the repair on my bike but it is possible that air can get into the hydraulic clutch system whenever you move those parts around
@marcosberto1
@marcosberto1 3 ай бұрын
@@LehewTech I think the leak increased after changing the seal... Maybe I did something wrong.
@TinManSimRacing
@TinManSimRacing 3 жыл бұрын
Absolutely a great video. Took me 20 mins to fix this leak and cost me 8 dollars. Thank you for the video
@davidblade7188
@davidblade7188 2 жыл бұрын
Hey. Where did u ordered the part?
@sergiocollection4471
@sergiocollection4471 Жыл бұрын
Where can I get the part?
@KJ6UXW
@KJ6UXW 4 жыл бұрын
Thank you. My 05 just started the oil leak from the same spot.
@TotoQuebec
@TotoQuebec 3 жыл бұрын
Thanks it help a lot to see it done... I just find that was my oil leak problem and the old guy at kawa explain me how to do it... but better to see it live 👍👍👍
@OrinLePirate
@OrinLePirate Жыл бұрын
Thank you so much, this video saved me a hundred bucks for a diagnosis
@XLR8RRICK
@XLR8RRICK 4 жыл бұрын
Pushing the seal on will cause the inside seal scraper be turned outward and will fail because it needs to be turned inside to seal. after the seal is installed pull out the push rod and when it is pushed back in the inner seal scraper will be in the right direction.
@TheDanLaid
@TheDanLaid 3 жыл бұрын
Do you have part number for that seal?
@gilbertblanco7002
@gilbertblanco7002 10 ай бұрын
Hi, thanks for sharing the video, I wanted to ask you where I can buy that clutch push rod seal online, as I am outside the US and it is very difficult to get that kind of stuff in physical stores. appreciate the help.
@RoadRamblers
@RoadRamblers 6 ай бұрын
Appreciate the video. Could you please share me with the part number for the seal and pushrod? I have the same model motorcycle too. Mine just started leaking after a long trip.
@RD1138
@RD1138 4 ай бұрын
Do you have a part number? I can’t find it anywhere on the diagrams of the bike.
@UncleGo67
@UncleGo67 3 жыл бұрын
Thanks for the Visual and tutorial...👍😎
@joshuawakeley217
@joshuawakeley217 2 жыл бұрын
Could you tell me the part number for the oil seal? Kawasaki just deleted all the parts diagrams for the older bikes this week off their webpage :/
@Ghxzt2161
@Ghxzt2161 4 жыл бұрын
Best thing to do to push it in is use the old see as the pushing surface and a deep socket as the pushing object
@paulmcleod1135
@paulmcleod1135 Жыл бұрын
Same problem just can't find the part number for the seal suggestions please
@glendonjarvis4045
@glendonjarvis4045 3 жыл бұрын
What is that brass circle there, I've got an oil leak from that, but I don't know what it is
@brianmccarthy9860
@brianmccarthy9860 Жыл бұрын
dude, put oil only on inside of seal , not outside, thats why it slips out when old, its not a bad design as u stated. thats how all seals work,. is that mayo on your shirt or didyou BLOW A SEAL?
@king_x_negus
@king_x_negus 3 жыл бұрын
I did have a crack in my seal at which it has been changed but I'm still having issues because all of my oil keeps leaking down my kickstand. And I can't figure out what to do next.
@marcosberto1
@marcosberto1 3 ай бұрын
It's the same on my bike, I installed the seal, but the leak persisted.
@mikerobinson9265
@mikerobinson9265 4 жыл бұрын
What is the part number? No one can seem to pull it up. Thanks
@LehewTech
@LehewTech 4 жыл бұрын
This is the part that fit for my particular bike www.partzilla.com/product/kawasaki/92049-1017 Youl want to verify that it works for your specific machine.
@jaydee8285
@jaydee8285 2 жыл бұрын
Exactly whats happening right now 3/22.....i had my bike sent to the shop to get new starter on...got my bike back and started once but started clicking again...so what they told me was they had to fix something else dealing with the clutch relay(part name could be wrong)..got bike back and rode it now immediately I see that same leak going down that shaft tubing without taking the cover off..it almost made me think that my oil drain plug was leaking and by it being on kickstand the leak flowed down it..but this says it for me i was sure they had something to do with that...i didnt have these extra probs til I took it to the shop
@bobbymairel5850
@bobbymairel5850 4 жыл бұрын
My seal is MIA and the rod wont pull out so i put the seal on and bled the clutch but it wont engage ???????
@danferland5322
@danferland5322 4 жыл бұрын
What happens when the rod doesn’t want to come out, what does that mean, and how do I remove it, thx
@inch830
@inch830 2 жыл бұрын
good job
@diegoalvarez106
@diegoalvarez106 Жыл бұрын
Was that oil leak coming down by your kickstand
@LehewTech
@LehewTech Жыл бұрын
Yes
@johnrobinson1547
@johnrobinson1547 3 жыл бұрын
What is that seal called and where can we get it
@johncombs6401
@johncombs6401 3 жыл бұрын
Where did you find that seal
@58gennaro
@58gennaro 4 жыл бұрын
I was with you till you mentioned the seal falling into the motor. How did you seat it?
@LehewTech
@LehewTech 4 жыл бұрын
You just push it in until its flush
@58gennaro
@58gennaro 4 жыл бұрын
@@LehewTech Thanks. I've been fighting clutch trouble. I think I'm just going to replace everything.
@codyhiatt77
@codyhiatt77 4 жыл бұрын
What if you have a oil leak to the circle on the right ( I don’t know what it’s call)
@TotoQuebec
@TotoQuebec 3 жыл бұрын
It the bevel gear bearing cap. It can need to be replace, it just push in place...no screw or bolt.. press fit
@-zack-attack
@-zack-attack 3 жыл бұрын
I tried to replace my and I accidentally pushed the seal on the other side and it fell down what do I do???
@motoradventureracing1386
@motoradventureracing1386 Жыл бұрын
It happened to me right now
@Tru_Justice
@Tru_Justice 5 жыл бұрын
Where you get the seal from
@fredbarnich8145
@fredbarnich8145 3 жыл бұрын
Do you need to drain the case?
@LehewTech
@LehewTech 3 жыл бұрын
No
@pepperjackshack2439
@pepperjackshack2439 4 жыл бұрын
The entire clutch system is a joke, idk who designed it but must have been the first time.
@brodriguez474
@brodriguez474 5 жыл бұрын
Where you purchase the seal???
@LehewTech
@LehewTech 5 жыл бұрын
Partzilla.com
@cookiemonsta3613
@cookiemonsta3613 3 жыл бұрын
Where can I get the seal at?
@TotoQuebec
@TotoQuebec 3 жыл бұрын
I buy it directly at the kawa dealer... under 10$... It a regular part number use at other place...
@alonzofisher1022
@alonzofisher1022 2 жыл бұрын
Do you have the part number
Vulcan 1600 Classic - Clutch Bleeding
34:40
Chef Hiker Biker
Рет қаралды 29 М.
Сюрприз для Златы на день рождения
00:10
Victoria Portfolio
Рет қаралды 2,7 МЛН
У вас там какие таланты ?😂
00:19
Карина Хафизова
Рет қаралды 11 МЛН
Mom had to stand up for the whole family!❤️😍😁
00:39
Replacing Clutch Spring on Kawasaki Nomad 1600
28:07
MeCoWhy?
Рет қаралды 37 М.
$3 Common Oil Leak Repair
9:10
Jeff's Auto
Рет қаралды 117 М.
Oil Leak Repair
9:25
The Motorcycle Boss
Рет қаралды 281 М.
Kawasaki fork seal replacement
25:55
Trucks And Junk
Рет қаралды 8 М.
Kawasaki vulcan clutch issue.
2:42
Joe Stewart
Рет қаралды 85 М.
How to Fix an Oil Leak (From the Shift Shaft Seal) on a Kawasaki Vulcan 750
8:27
Checkered Floor Garage
Рет қаралды 2,7 М.
kawasaki 1600 engine rebiuld #1
16:13
139check
Рет қаралды 45 М.
Сюрприз для Златы на день рождения
00:10
Victoria Portfolio
Рет қаралды 2,7 МЛН