Today we are fixing all three bikes. Each bike has a different problem. I'll be going over a few details that I have not covered in past videos.
Пікірлер: 122
@hardtruth79883 жыл бұрын
17:55- aww damn😅 Did the same thing recently, that can be frustrating. Thanks for the step by step again. These vids are much appreciated because of that, along with the tips.
@keeganhache66673 жыл бұрын
I’m in Canada and I live on a dirt road. I’m cleaning my carb 2 times a month lol
@tylertillema59343 жыл бұрын
Make a gaurd for the air box
@Centar19643 жыл бұрын
Your mistakes like "put the cylinder on backwards, I sure did" and "if that wasn't a big enough kick in the nuts" are one of the reasons I subscribe to this channel...makes you very relatable...you keep it real and you should make a "mistakes out-takes" video...and on the subject of break-in oil ratio (16:1) my take is it is for getting the "dry" engine lubed up and avoiding piston/cylinder damage (it actually slows the break-in of such) also it has been shown that anything richer than 20:1 provides no extra piston ring sealing...so in conclusion I would run 16:1 or a new engine but no richer than 20:1 for a new top end break-in.
@thingstuff84613 жыл бұрын
Quick question, whatever happened to Old Faithful?
@LAHover3 жыл бұрын
I retired the frame, it's parts have been spread among the remaining bikes.
@thingstuff84613 жыл бұрын
@@LAHover Oh I see. Was the frame itself unsuitable for continued use? (it being a $98 bike). Thank you for the reply. I've been subbed for 5 months.
@soggyridesmotorizedbicycle6258 Жыл бұрын
Yeah, that's the thing with owning a fleet of motorized bicycles. Sometimes those fixes can get piled up. Your bikes sound and look great.👍👍
@PlayingWithFireOutdoors3 жыл бұрын
I hope you're doing well, my latest nightmare / project is a Honda ruckus. I need to replace the gas tank & cap . It was left unused for 6 years. Sigh, vids when I dive into this !
@shakurvariawa83153 жыл бұрын
Hey man i've been looking for videos on how to make these things softer but all i can find is videos on how to make them louder. You seem to know what's going on. Any suggestions?
@Robert-hf5xr3 жыл бұрын
If you want super quite get a Chinese banana pipe they kill the sound lol
@shakurvariawa83153 жыл бұрын
So i've been messing around and i found some solutions: 1- cover the clutch cover with rubber alot of noise comes from the gears inside there 2- put small pieces of rubber between the fins of the motor. 3- put rubber between the motor and frame 4- wrap the muffler. I tried packing it but there was too much restriction and it wouldn't start 5- build a box around the carburetor and fill it with steel wool. this will take out most of the high pitched whinny noises and drastically reduce vibrations. It's a bit of work and there's a lot of tinkering you have to do but the end result is something that sounds more like a motorbike and less like a weed wacker. also because the bike vibrates less it's easier to take it up to higher speeds
@joerillarilla85243 жыл бұрын
What do you mean by softer do you mean quiet the stock exhaust is super quiet compared to what I run if you want quiet go Electric either that or get a 49 instead of a 66 you can add baffling to it will make it much quieter but I must warn you it takes away from speed. Type of Motors run on the air fuel mixture you can make it as quiet as you want but you will not get performance you want silent go Electric. In my opinion I like an engine I don't want batteries
@caduceus333 жыл бұрын
Seeing how things looked in that YD100, I would run it till it was starting to run poorly.
@joshuayaddowmotorizedbicyc77083 жыл бұрын
Thanks again for another useful video got this saved to the 2stroke Playlist so I can easily go back and watcher again if I come across any problem 😀 thanks bro
@22sabian3 жыл бұрын
Hey, cool video. Lot's of good info. Also concerning your gasket making techniques, wouldn't it be easier to simply trace out the old gasket you're replacing? Oh and what an awesome riding buddy you have. Say hi to Henry for me.
@Jeff_Green3 жыл бұрын
I would love to see a magician update!
@bartsshorts9 ай бұрын
i wonder if its possible to have a electric motor force pressurized air thru the carb? like a supercharger
@themo24763 жыл бұрын
Got some work to do on my bike too crashed her and broke my wrist but hopefully will be back riding in 5 weeks
@LAHover3 жыл бұрын
ouch! sorry to hear it man.
@Pigmaster63733 жыл бұрын
Love your work man
@davedaisy94173 жыл бұрын
How do u send pics on here so I can show u ?
@Tom-zv9fl3 жыл бұрын
nice
@SmokeyVlogs3 жыл бұрын
Omg you have main double stand , epic🙏😎
@joshuam78183 жыл бұрын
Would u recommend the zeda triple 40 firestorm or the Zeus t 100, I'm about 200 lbs and I want to use a 36 sprocket
@LAHover3 жыл бұрын
If it's your first build I would get the triple 40. if it's not, than definitely go for the Zeus.
@GeorgiaRidgerunner3 жыл бұрын
La hover im enjoying this cooler weather too just about 6 weeks or so were getting 99to100 actual and feels like 103-105 of course a few nights ago it 50 degrees and i was freezing had to pull out a blanket
@Jetsonn2 жыл бұрын
I love your sweet dog
@phrodendekia3 жыл бұрын
Sometimes, making gaskets for chainsaws and trimmers to cut the round part for the cylinder bolts (in this case for the studs) I would place a ball bearing over the hole and punch it with a hammer, the ball will cut a hole on the gasket by pinching it when it accomodates on the stud hole.
@ramiallan5256 ай бұрын
I love your videos bro keep it up
@WhiskersTheFish3 жыл бұрын
What oil gas ratio would you recommend for a 2 stroke motorized bicycle? Also what would you suggest a good way to seal an air leak where the carb connects to the manifold?
@iceyaj31673 жыл бұрын
i use gasket maker
@WhiskersTheFish3 жыл бұрын
@@iceyaj3167 Like the liquid? What color/type?
@iceyaj31673 жыл бұрын
@@WhiskersTheFish its not a liquid. its more like a paste. it come in red or black. RTV silicone is what i use.
@WhiskersTheFish3 жыл бұрын
ice yaj I put some red gasket maker over the slits on the carb then put the clamp on and put some tape around it. It did not fix the leak 100% but it idles for a while and revs come down slow but come down.
@iceyaj31673 жыл бұрын
@@WhiskersTheFish did you let the gasket maker dry and cure?
@jonchannel73113 жыл бұрын
Ajuste de carburador the float end to top 21mm exact para que funcione y corra bien el motor
@carlcustomer13793 жыл бұрын
My question is and I do appreciate your video clips on having trouble with but so I put them in and then Vegas connect to the bar. Pinhole on top it doesn't matter that's my question
@LAHover3 жыл бұрын
I do not understand the question.
@epicwinfacepie3 жыл бұрын
After you put a new Piston and cylinder on the yd100 are you using 16-1 aka break in fuel again or are you going to just continue your regular mixture. Also how many tanks are you going to use to break it in?
@LAHover3 жыл бұрын
20:20 - 21:21
@possibleproblem4793 жыл бұрын
mine makes really loud squeaking noises which seem like their coming from a bearing inside the shaft that goes from the drive sprocket to the clutch. the problem is they’re plenty greased and it only squeaks when it’s warm. and whenever I let off the clutch that really raspy noise progressively gets louder each time I run it. I don’t ride the clutch and I try to make sure the engine rpm matches my speed every time I let off so it’s not like I’m hard on it. oh and it only idles when it’s cold, not when it’s warm for some reason. I thought that was only a problem for larger cc 2 strokes lol
@franciscoholguin80183 жыл бұрын
This is pancho from discord good video👍
@raymondshrader3555 Жыл бұрын
I wish I had a friend or neighbor who knew about these bikes, just to kinda help me learn and get started on these bikes.... It seems kinda risky to start spending the money on these engines without the know how....
@historygradstu2 жыл бұрын
In your opinion, which motor is the one you like most...Iam wanting to do a conversion but don't know that much about the various motors. Any help would be appreciated.
@LAHover2 жыл бұрын
Firestorm Zeda 80 is my #1 pick. The price is a little high right now so I would also be happy with a Wild Cat PK80.
@aztecworrior793 жыл бұрын
Hover What oil ratio mix do you run on your motorbikes ?
@davedaisy94173 жыл бұрын
Don't feel bad I mite of done it when I was younger. Hay when r we goin 2 the motoos. I'm still buildin my chopper. I also found out it's a quad 40. Bore stroke intake & exhaust. I'm mostly waitn on a front cnc mount. Cause the frame is so long. Reoder it twice. Cause amozon prime lost it. I've been havin trouble findin a rear wheel 4 it. I'm runnin a 26 on the front on a dual springer. The rear a 24x3 tire. But the problem is the rear frame is 4 1/2" axel openin. So I need a 4 1/2" hub. On th rear wheel. Do u have any ideas ? Thanks. I'm glade y'all made it through.
@williamdooly41113 жыл бұрын
Have you ever changed a rod bearing on the crank and if so how do you go about it
@LAHover3 жыл бұрын
I have not
@marcusdorsey70573 жыл бұрын
I have a rough mid/high throttle on a zeda triple 40. Takes off great with good power but after I get it to mid or high she's nothing but 4 stroking. I'm still in break in and I'm running 16.1 ratio as the manual states. I have adjusted the NT carb. Any tips?
@LAHover3 жыл бұрын
if you are passed one tank, go ahead and switch to 32/1. That alone should help, but if it still struggles, try moving the needle clip up 1-2 notches (leaner). And if that does not help get a smaller jet.
@ediot.10123 жыл бұрын
So what is the top speed for the yd100? I want to change my bike for I can go faster but not too sure if the yd 100 we go faster then 37mph
@LAHover3 жыл бұрын
My best top speed with the yd100 is 42 MPH on flat ground. Here is the set up and video link. 26" frame, 36 tooth sprocket, ngk b8hs, port matched and polished. kzbin.info/www/bejne/h17EYoSfqteFgqs
@ediot.10123 жыл бұрын
@@LAHover thank you for letting me know.
@joerillarilla85243 жыл бұрын
change ur sprocket put on a expansionchamber ngk plug nt carb is fine when tuned correct. dont go crazy and waist money on boost bottle also make sure u break in correct .remember these r 2 stroke motors break in is everything .then tighten everything up make sure you don't have any vacuum leaks air fuel..that's the best advice I can give u bro
@williamdoire68533 жыл бұрын
Hello i was wondering if i should pull my head and check how my jug is doing have a second hand motor have no clue what the miles on it are prob close to 200 i do ride it a bit and some times it seems to strugle for a moment then its fine but can i just pull the head check and slap it back on if i dont mess with the gaskit just clean the suface i also have 2 spare jugs that have been fully ported not shure if ill use them yet think i may up load a vidieo if i find my jug to be dammaged just making a list of what to put in it at this poit hahaha
@caduceus333 жыл бұрын
KZbin has stopped sending notifications where a channel someone has subscribed to has posted a video. If I had a way to do it, I would let them know that it is much better to get those notifications.
@codelicious65903 жыл бұрын
It is frustrating that most piston kits and pins never come with the bearings but I found one on Amazon that comes with pin, clips (good ones) and wrist pun bearing for same price as just the pin and clips! It's from seller, "DONSP1986" I've also found other motorized bike items from this seller to be of the best quality. The best quality one can expect from redistributed Chinese parts that is.
@carlcustomer13793 жыл бұрын
I'm going to look into it and c that this bike cars are easy to work on this bike though it was not as hard to get it done before Snow hit a
@carlcustomer13793 жыл бұрын
And
@carlcustomer13793 жыл бұрын
Thanks I wish I would have got a friction it would have been done easier but they didn't have none and stacked when I was trying to get it I would say by 1 I have a good one
@KenC56mm3 жыл бұрын
You guys know if the yd 100 needs BOTH BASE gaskets that come with the kit?
@LAHover3 жыл бұрын
none of my motor came with, or have two gaskets. Removing one may give you more performance, but you need to check the squish gap.
@KenC56mm3 жыл бұрын
Huh. I ordered a new gasket and it came with two also. Thanks for answering L A.
@epicwinfacepie3 жыл бұрын
Yo I was wondering, can you put a yd 100 cylinder and piston on any old china doll pk80? Like are they comparable?
@LAHover3 жыл бұрын
No, the cases are to small to fit the jug without extensive modification.
@carlcustomer13793 жыл бұрын
Speakerphone I'm sorry the clipse they just go in in the hole on top I I don't got to worry about
@joshuayaddowmotorizedbicyc77083 жыл бұрын
15:10 what is that you are applying
@LAHover3 жыл бұрын
oil to the needled bearing and rings
@tuktakbangla3163 жыл бұрын
Good
@engineguyrojo68933 жыл бұрын
It the yd100 actually a 100cc
@christianscottsuzuki3 жыл бұрын
You can google it as well but now its a 78.2cc
@joneserupinsmoke91612 жыл бұрын
Hover any clue in what blows holes in pistons?
@LAHover2 жыл бұрын
Never ran into this myself but from what I have heard is, as long as the sparkplug is not contacting the piston, the motor is simple to hot... Running to lean, to much oil, full throttle for to long, and a hot plug rating. Probably a combination of the above would do it.
@joneserupinsmoke91612 жыл бұрын
@@LAHover thanks bud but how is ur phantom running? My 1st 2nd gen all types of metal fragments were in the crank case and got it to jug and blew it up now the place I got it from is telling me to break in at 25 to 1 and then 20 to 1 from there out .what have u been running ur at?
@joerillarilla85243 жыл бұрын
bro I was listening closely to ur first comment.u metioned something about a key way r u referring to the woodruff key it acts like a shear pin..I lost engagement I heard something give and immediately shut down although I noticed it was catching I heard a metal on metal snap and sound I believe I just sheared the key way so I did not attempt to driving but no it was catching I knew something was wrong and I heard it break so I just disengaged the clutch and peddled to do no further damage how easy is it to replace that Woodruff key do I need a puller I have built over 10 of these bikes sometimes you get better quality than others that's just the way it is with these. As I'm sure you know a lot has to do with the break-in and how you ride it I cannot emphasize Loctite enough where is it is able to be applied of course I'm not talkin on the head bolts tell when I get a new motor I like to take them apart and make sure everything is good this particular one I did not it was running perfect stock except for expansion chamber and NGK spark plug I have had other issues with these but never this happen do you have any advice I have six other Motors I use for parts my best build ever was on a beach cruiser I put on a hub adapter 32 tooth sprocket I broke it in with bigger carburetor and true expansion chamber although I must say my first tank of gas I would let it heat up without a load on it cool down ice cold and then after that tank was almost empty take it on a ride always varying the throttle that was my best build ever I kid you not bike went over 58 miles per hour once it was hot and of course something happened with that one that it got stolen it was my best build ever I was super pissed about that I love these bikes though they are the way to go please let me know if you have any info about replacing the key because I think that's what my problem is I know all about the clutch plate and pads something gave I hope it did not go into my case luckily had enough sense to turn it off immediately but it was trying to catch as if part of it was still there that's what tells me it was a Woodruff keyway young people call it a half moon I am familiar with the flower nut adjustment it is not that I have yet to take it apart but I miss my bike so I need to have one running again any tips you got for me do I need a puller I don't have fuel. That one came in originally
@MrCrawford773 жыл бұрын
I have a question to you have you ever seen a 80cc with a cylinder and head one piece
@MrCrawford773 жыл бұрын
I just don't know what to do about upgrading it I wanted to do a different head and stuff I wanted to shave my cylinder just to play with it and I look at it and it's one piece
@MrCrawford773 жыл бұрын
I wanted you to text me so I could send you pictures
@LAHover3 жыл бұрын
I recently picked up a 66cc with a 1 piece jug. after removing the jug it does look like you can fit a two piece kit on it, but you would have to drill and tap it for studs. It currently uses smaller alen bolts.
@MrCrawford773 жыл бұрын
@@LAHover yeah I didn't notice it until it got to me it said 80cc on eBay and now I'm hip to looking at other things but it has the Allen bolts around the rest of the motor so I thought it was just a newer updated one
@MrCrawford773 жыл бұрын
I wanted to text you anyways I'm just talk to you regularly just about questions about these motors cuz I like messing with them too
@christianscottsuzuki3 жыл бұрын
Youre supposed to clip off the wrist pin clip ears. Two strokes arent supposed to have ears.
@christianscottsuzuki3 жыл бұрын
kzbin.info/www/bejne/gXe6lHRmbcaHea8
@christianscottsuzuki3 жыл бұрын
kzbin.info/www/bejne/bX6Wep-efb1-hs0
@christianscottsuzuki3 жыл бұрын
Those videos i linked are how to cut a slit in the piston hole to be able to install the "C" wrist pin clips so they dont destroy a head, piston ring set and piston due to the ears snapping off :)
@carlcustomer13793 жыл бұрын
Thanks search for thanks for the videos I think I could put the clips on what's the difference between a 6680 in cheap a TI-84 Plus work by friends got one
@carlcustomer13793 жыл бұрын
Speakerphone sorry one part of the clip goes on top of where the hole is right
@jimmyreed47222 жыл бұрын
I like your vidio i love the 2 stroke and.dud old man i like that your strait up dont let the ass holes talk bull shit your doing a good job
@joshuam78183 жыл бұрын
Hey how much do u weigh?
@LAHover3 жыл бұрын
175~
@carlcustomer13793 жыл бұрын
I click like like I think I could put these clips and just fine I think anyways what's the difference between in 80 my friend's got 80 and I got to 6680 I mean his has a lot less work and was cheep
@LAHover3 жыл бұрын
Commonly know as the 66/80cc motor. Although there my be slight differences in parts and quality they are the same motors. 66cc is the American displacement measurement.