LCA Draw Board + Instructional Video

[@donfrance3]

Just bought one of these handy dandy tricky well designed jobbies because of your video. This is way better than the old boat crank repurposed after the boat sank dealeeo on a 2 by board. Anyways .... Thanks!

[@ScottPankhurst]

first thing I did with mine was flip it to lefthand orientation. it makes it a little more awkward to use, but being able to clearly see the draw stops hit the cables is worth it.

[@jeffgenchi5863]

My lower cable came out in my brand new LCA Draw board launching the book into me QAD rest almost dry during my Matthews bow. LCA was awesome and took care of it. Still getting the trust back considering it cost time and my rest is still at QAD. Had to buy another rest to use my bow. But LCA took care of me no problem.

[@iamSofaK1nG]

thanks GRIV

[@scottlandb6579]

Y’all need to make more videos

[@iamsecond3625]

Thank you!!

[@bltefft]

I have the older version LCA draw board on my LCA Ultimate Press and sure liked the way this new winch let off without having to hold a release lever forward. Is it possible to upgrade my older LCA winch with one of these newer versions?

[@LCArchery]

Hello, yes you can contact our office and you can purchase the Draw Board upgrade for $50 + shipping. They'll send you an RA# and what you'll do is return the Draw Board to us here and then we will preform the upgrade to it. Thank you

[@bltefft]

Thanks, I called. My old winch is on the way back for the "re-build".

[@LCArchery]

@@bltefft That's great to hear. We'll get it upgraded and returned to you as quickly as possible.

[@2ndAveScents]

Isn’t the tube steel square? Why couldn’t you just pull out the winch and rotate it and slide it back in to the press instead of flipping the whole thing? Is there some kind of reinforcement in the press arm blocking that?

[@LCArchery]

It is a square tube, but the topside within the tubing has a mounting plate where the block is attached to install the press fingers.

[@abaddonbc3844]

If you have an Ultimate press how far extended does your press need to be to use this? Should you extend it to full out or just play around with it to see? I just got an Ultimate delux and this draw board for the ultimate and haven't used it yet because I literally just set it all up.

[@LCArchery]

Good morning! You can adjust it around until you like it. Nothing has to be particular overall; you just need to ensure you have enough room between the press so you can draw the bow to full draw. Other than that, you'll be good to go!

[@abaddonbc3844]

@LCArchery Good morning! Fantastic! Thank you for this super instructional video. It's helped tremendously!

[@XxPackerManxX]

How do you check draw length? I'd like to add I bought one of these and I'm not real impressed. The rubber band broke instantly dude is crazy taking his hands off the bow and just leaving the bow hang by that cheap rubber band. I feel this simple contraption is way over priced especially because you can't measure the actual draw of the bow.

[@LCArchery]

Hi Marsh, there's a few different ways to check the draw length, but each way requires either a long ruler, or a measuring tape. There's a few different options and the best thing to do is hope online and watch a few videos through KZbin about checking Draw Length. There's different archer's that like different methods, and you can figure out which method you like best.

[@XxPackerManxX]

@@LCArchery I mean checking the draw on the actual bow while being in the draw board.

[@Shiwwy]

Thanks for info sir.

[@E-M-C]

I had the same question, and the best solution that I've found is to buy something like the Easton Draw Check Arrow, which has measurements written on the arrow. Nock that onto your string, draw back with the LCA draw board, and check the measurement.

[@TheBowdoc1]

My 2019 carbon Hoyt does not pull straight. So when I set my timing it’s actually not in time when I actually draw the bow. Does anyone else have this problem? Or am I doing something wrong! My thumb portion of my drop away rest also hits the rod.

[@LCArchery]

Hello, email us and we'll be happy to help you. Or you can visit our website and send us a website contact form that we'll also be able to respond to.

[@jamesdaly5295]

It's because the winch is 2-3 inches below the arrow or nock point! Does not give accurate readings. You can prove this by checking the timing with the draw board and then with your release. You will get grossly different timing reading.

[@nolanwilliams3007]

First comment!

[@noeramirez4975]

Sorry, this need better quality and more precise details. Mine almost broke my fingers, the nylon broke an accidental shoot occur.

[@LCArchery]

Good afternoon. We'd be happy to help you with your draw board. You can reach out to us here: lastchancearchery.com/returns