Transponder Chip Key Bypass How To For Any Car!

[@philipmcclellan4989]

Your video saved me a whole boat load of cash. I went to start my 2001 Ford Ranger and the end of the cylinder broke off inside the ignition switch and my truck dead in the parking lot. I was able to purchase a new ignition at my local NAPA store but they were not able to give me one with a transponder key. However the ignition switch fit and I was able to turn on all the electrical but not start my truck. After watching your video I tried to use my original key by placing it as close to the ignition switch as I could and turning the new key to try and start the engine. IT WORKED ! I did however have to take the plastic cover off the underside of the steering wheel. 3 phillips screws, less than a minute to remove in order to get the transponder key close enough. A million thanks !

[@lvd2001]

Thank You - You save me heaps - instead of buying a new programmed key from dealer at $150 - it Cost me only $6.00 blank from ebay and $10 labour cost for cutting the blank. ow my new key works like a charm.

[@ricglass2794]

Good idea, I've done this and it works. I also had a pass key ($10) on the same ring as the chip key and it also works. I leave the pass key on the ring and remove it for the kids to get in boot etc when I need to, they cant start the car with pass key this way but after taking out transponder and gluing it to steering column, THEY ALL WORK ALL THE TIME. Well done

[@morecowbell9832]

Thanks for talking about the door in the Ford-style key, that was a handy bit of info. I took the transponder out of my Mazda key by pulling the door straight out. The door is a long piece of plastic that extends into the key body and inside the plastic housing was a tube-shaped transponder. It looked like the chip our vet put into our dog. I found that the transponder can't be too close and can't be too far away from the lock cylinder. If it was touching the lock cylinder in the steering column, it would not work. So I put it in a small length of plastic refrigerator ice-maker tubing and melted the ends to seal it in there, and zip-tied the tubing to the lock cylinder. The transponder hangs down and out of the way. I also had to make sure the transponder was out of the way of the shifter linkage before putting the housing back together.

[@leebaker8195]

This is a very good video and money saver. You will always have those who looks for what they perceive to be a deceptive explanation. But whether it is a true by-pass or not doesn't matter at all as long as it works and saves money. Yes, the chip is still needed or there will be no communication between the key and the car. So I will encourage all to be very careful to not lose the chip. Make sure it is very secured in the key shroud area with a very good glue or tape. If you lose this chip, you will pay for it. Excellent video. Oh by the way, Home Depot makes the chip keys for about a third the price of the ford dealers.

[@paigejones]

Just saved my life, or at least an expensive tow on my 2012 Malibu! Thank You!!!!!

[@alexluckes6563]

Didn’t realize transponders work against each other thanks so much

[@alphadominance6242]

Bro i love you mahnn you saved me a 40 bucks got it all done for 3 dollars and made the duplicate for 3 total 3 dollars instead of a 50 60 dollar in india the fuxkin shop owner tried to scam me then after doing the cutting he said he cant do anything in my key bcz its only cutting can be done there and i was a bit hopeless thought he scammed me after cutting it but your video made my whole day now i got a cool key i just placed the chip in my new key socket i saved alot and you got a sub

[@mdmeadmdmead]

Wow, amazing some of the comments! Personally, I think this info is worthwhile. I've got an older beater car worth maybe a grand and minimum coverage on it. Not too worried about it getting stolen. What I do want is another key, without paying more than a couple of bucks for it. If this gets me there, I win. (If someone here wants to come steal it, let me know, and I'll help you get it off my property.)

[@stevebrown7968]

mdmeadmdmead k8

[@Dad_a_Monk]

Damn I had an old truck I never locked and literally left the key in the ignition all the time. Drove it anytime I needed a truck for years. NEVER got stolen...even downtown. Even crackheads didn't want to steal an old beat up horse truck

[@democracyblog]

Worked for my 2003 Ford Taurus w/ factory "S" coded key. !!! Note: Chip is in lower right corner as looking at Ford logo and set in only 1/8" from corner. Avoid cutting here !!! From right edge of logo across top (just chop off loop) and all left side you can cut deeply to the key with no damage to chip. Had to pry against key and peel back with pliers to remove factory cover and chip. After several tries I found placing chip at 1 o'clock position AGAINST the black ring which energizes / reads the chip worked. Sealed chip into duct tape and held it there. Thanks Lessco, this saved me $70.

[@billb.4901]

Another time this might be useful is in a situation where the key won't turn the cylinder on the lock. Ignition switch replacement and reprogramming are a little pricey. If you took out the transponder, you could leave the key in the ignition rather than replace, and when you want to drive just attach the transponder near the switch. You could make some type of pocket and mount it near the switch, into which you could slide the transponder.

[@denniscurtin6796]

Billy B

[@VendettaNC]

This is silly. Just do what he says in the video. Much easier and makes a lot more sense tbh

[@GlobalSecularism]

In order to complete the bypass, the transponder will need to be placed permanently onto the ignition keyhole. This way, any key will work since the antitheft system will always recongnise the transponder (permanently attached).

[@ayshortier]

Good idea. I like that better. I almost lost my key because the ring broke, and I prefer securing the chip.

[@emily1]

For insurance purposes you probably shouldn’t do that

[@manuelcalbert3404]

It just has to be close to enough to the ignition for the signal to be picked up

[@battlehrfred]

I did this as he said on a 1999 ford 4x4 It worked great!! the thing is If i lost the last set of keys for this truck it would cost me a small fortune to be/ towed to stealership /reprogrammed/ plus 2 keys= 500.00. no thanks!! Now i have 3 keys =12 bucks.problem solved. K.I.S.S. eXCELLENT VIDEO 100-100

[@illinoisvideoatlarge8039]

+battlehrfred Yes, 4 runner 2008, I found out that I can only have the 3 original keys and one programmed, the fourth one would not work, but I can use it to open the door. I went to Lowes and then used the KZbin instructions, 5 ignition passes and 6 door closings...etc. to have one extra key now.

[@clubbanker]

Fantastic, had to replace my ignition barrel as it had snapped, back on the road now after putting chip in new key. Thank You.

[@ricglass2794]

You can get as many $10 keys as you like and they will all work, if you take the transponder back out and glue it to you lock/near your lock as described in this video

[@rollergirl408]

Thanks for posting this video! Don't even respond to the others giving you grief :) I have an Isuzu Rodeo that came with one key and I CANNOT get more keys! There is no Isuzu near me to make any and the locksmiths around here can't as well. So I'm going to put my chip near my ignition and use non-programmed chip keys that the locksmith WILL cut but can't program. I am terrified to lose my one key because then my husbands work car is just scrap metal. There is definitely use for this video. Sometimes you have to do what you have to do!

[@rayed51]

Thanks a lot. Well done mate. Got me out of the crap. Bypass or not, bit of semantics going on here, its brilliant information and presented really well. Like the simplicity of it all.

[@rubenmbrah155]

foolish

[@dedios03]

​you must be from the manufacturer 😂

[@oni_goroshi]

What makes it foolish? Not wanting to pay a lot of money to get keys programmed? It's not like someone who wants to steal your car is going to know this was done. You probably think your home is safe with door locks.

[@JustOneCalorieNotEvilEnough]

A giant 'Thank You' for your candor!

[@Lesscoelectronics]

Thanks for listening

[@JCisJD]

Im not sure if im missing something here but if this is just about only having one transponder key left why not just hide the key in the dash/ close to the ignition and just get a spare , none transponder, key cut ? If you sell the car then you can sell it with a complete key. What is all the fuss with cutting the chip out ?

[@Lesscoelectronics]

reliability is why I do it

[@JCisJD]

Lessco Electronics Cheers :)

[@EarlGuyton425]

JCisJD That's how I do it. I put the 3 dollar re cut key and hold the transponder key next to it and start my truck then stick the transponder key back under my dash which is the same thing but you aren't leaving the chip exposed for another person to take. Which is better because what if your car was ever towed and some chicken shit wrecker driver takes his thumb nail and takes that chip off the ignition ring??? Youre up chit creek.

[@Lesscoelectronics]

The reason why is reliability, No key taped under a dash will stay there perfect for long, sooner or later trouble will strike.

[@307rekordzsouthweztrydazcrew]

Earl Guyton thanks alot man..i tried wat u said n it worked

[@my2centz196]

I would had like to see a more detailed position on where to put the key over the long part about saving the mold key lol. Either way definitely seems like it would work I was thinking of doing the exact same thing but putting the chip kinda in the steering column to hide it. My mother purchased a used Honda crv with only 1 remote key. I can program the remote however that's not gonna help with the chip working the ignition unless I do as you said. I have a few questions 1st the keys I'll be using are remote key fobs with chips that are easily removed. Will these work as well on the Honda. Also will the key work for the door and is there a chip reader in the door locks.

[@mujawidahmed2388]

On my old car i had glued the whole transponder key to the inside of plastic around the ignition lock & used locksmith keys for the ignition. This maybe a better option in case security is not a concern.

[@chumlichumster4582]

6

[@user-md3is4dq2d]

Just means anyone can steal your car in a matter of seconds

[@mujawidahmed2388]

@@user-md3is4dq2d My bad, it should've read, "...This maybe a better option in case security is 'not' a concern. Now edited. Thx.

[@oni_goroshi]

You don't know much about stealing cars, do you.

[@andrewjermaine312]

This was very helpful for me today, thank you very much.

[@giftgram]

great informative video. very practical and ingenious

[@trevorsams7608]

I have a European Nissan Patrol 4X4 similar to a Landcruiser. I damaged one key and had the problem that I could not get another one coded to match the other one good key I had where I live in the Caribbean. I just removed the steering column cover and zip tied the good key to the barrel. No risk of damage to the glass encapsulated RFID (Chip) by trying to extract it from the key plastic and yes these often come in a glass vial, real easy to break. There is no messing with the wiring. Took a little time to get it positioned right. Its been there now for nearly three years and my vehicle goes off road shaking things up real well. Purchased a couple of regular keys to have cut with aftermarket keyfob plips to operate the door locks and just signed them onto the system, It may not work for all cars, it depends on the sensitivity of the receiver on the lock barrel but just try a few positions keeping the head of the key as close to the key end of the barrel as possible and rotate the key a few times, checking at which point it will start. Took me about 1 minute.

[@HILUXCHAINSAW]

Some people are taking the title a little too literally. I did what the video said and now I can start my Hilux with 3 keys instead of only the one key that HAD the transponder in it. It gives me peace of mind knowing if I loose one key I can still start the truck with one of the others.

[@Discreetsecuritysolutions]

You should forget that peace of mind - now anyone with a good screwdriver can steal your truck. You've saved £40, but it could cost you your entire truck- well done.

[@jefris]

well anyone with good screwdriver can come in to your house? Is that what you are saying? Does your house key have transponder? You people are full of bs. Back in the days, just flashing led light on the dashboard and the club on the steering wheel worked. What else do you need to get ripped off by the car makers?

[@sparky6086]

@@Discreetsecuritysolutions Depends on how old the car is & where the the person lives. In many areas, cars were safe for decades without chip keys. I live in a sparsely populated area with very little crime, and no one would want to steal my beat up 16 year old cargo van anyway, so this solution is perfect for me

[@trombonemikey]

Very impressed with the information. I bought my ford Explorer second hand but was never told how to open the door with the numbers on the door. I found out how to lock it accidently.

[@joeyfitzpatrick6906]

If you want to find you "Door Code" for your explorer, You need to locate your GEM(General Electric Module). Not sure what year your explorer is, but most explorer GEM modules are mounted on the back of your fuse block(Under Dash fuse block just left of the steering column) On the GEM module, there will be a Label/Sticker with lots of numbers and info.(Part #'s and Serial #'s) There will be 5 numbers larger than the rest. This number is your Master Door Code. This number is unique to the GEM itself and can not be changed.(You can add extra codes though. Read how in your owners manual) Sometimes you can use a mirror to see the number with out removing the fuse panel. To lock the doors you simply push both of the right side buttons at the same time(7/8 & 9/0) quickly press the buttons again to set your alarm(if it is equipt with one). to unlock- enter your code. If you want to open the other doors too, press 3/4 after you enter code(on some models it is not 3/4, its the last number of your code- after code is entered just press the last # again)

[@MSG685]

I had an 03 merc sable. the door code was printed on the the component that was located above the brake peddle under the dash. I just held my phone down there by the break and took a couple pictures up into my dash . I got a picture of it with the first shot. easy pesy.

[@trombonemikey]

My Explorer 2003 Sport trac

[@jasonsuthern6326]

I'm a locksmith and the reason why we don't cut them is because the cheap Chinese Keys are sent with the wrong program chip. Also the keys don't sit right on the machines. Last some of these eBay, Amazon specials have Alloy Metal which mess up our cutter wheels that cost $300 plus. Also most locksmith shops are mom and pop and depend on business like this to stay afloat. All because we care to give you a good product. We also take on going car education to service our customers.

[@eksine]

this is incorrect. I was able to go to walmart and they told me only their transponder keys work for their programmer, WRONG. I gave them 4 keys bought from ebay, first one didn't cut right so I went to 2 other walmarts, one walmart didn't even have the keys to their key display but the 3rd walmart all 3 ebay keys were cut and programmed and they did work in the car, the cut's were not good on 2 of them because it was a copy from a copy, no original key was available but my other honda key was original and it was cut and programmed perfectly. so your information is wrong

[@jasonsuthern6326]

+eksine They use an Ilco brand programmer cloner. If you have an older Honda like early 2000 plus. Then most cloner equipment like that will clone what you brought in which is a TP05. Newer Hondas and Dodge etc. with remote heads don't work half the time because these eBay companies sell customers the wrong chips to add keys to vehicles with computers that have to be connected. Which are newer 2008 and up.

[@enri74cv]

I have insurance plus my car has automatic locks and a expensive alarm . when i bought my pre owned car i only got one key. So this is a nice thing to do. Awesome thanx

[@mightyspuds]

BTDT.Works like a charm if you only have one key and it isnt the master.saved a bundle doing this on my LS400.Got 4 working keys for less than 50 dollars.

[@medina5k]

you might also want to add, as an annotation, that if the transponder is damaged at any point during this removal the cost of repair is anywhere from $500-1200 to reprogram the module on the vehicle that stores which transponder is valid. This is in addition to not being able to start your car too.... as a locksmith of 20 years, i can't really approve of doing this... but this WILL work. and as for using another key that has a transponder on a lock that has this 'bypass'.... each transponder sends what is basically a password (16-32 digit hexadecimal password) to the computer that controls either the starter, or the fuel pump. if you have two keys in proximity of the antennae under the ignition cap the car won't know which password to verify. regarding how far the transponder has to be to be picked up by antennae? from the keyhole itself.... about the size of a soft ball... that is about how big the magnetic field is in these transponder keys that go into an ignition. the field is much much larger in cars that have a 'Push to start' button

[@googleguest4837]

Kroenan ....on my 2005 caravan i tryed using my door key with the chip key on the column. It only started for 3 seconds. I tryed moving the chip key around to get a better angle but no luck. I thought i caused a security issue so i tryed the chip key and it started ok.

[@janetbowersock4360]

I have a question. Sorry if it sounds dumb. i just want to see if it works. If I make a spare key for my truck and insert the spare key in the ignition, will it start? Keep in mind, I will make sure the original key is right next to the spare key. The original key will have the transponder inside it still. I just want to make sure it works before I take out the transponder?

[@JayCras]

Thanks for a great video. These idiotic transponder keys are sad excuses to charge insane prices for duplicate keys. A "key" is still a key and frankly that is all the security I've had for every car I've owned up until I bought an RX-8. I can't believe people ever accepted the concept of paying hundreds of bucks for a spare key! More computer crap = more things to fail. BTW I just looked at the insane turn on your car 3 times open and close the door over and over while you lock and unlock the drivers door thing. You guys know that some programmer wrote this code for laughs. Right? think the marketing folks who came up with the hundreds of dollars spare key nonsensee are laughing themselves sick when they go to the bank with your money. Personally for added security I took the duplicate key money and used it to put in a useful car alarm system.

[@ayshortier]

That's a great idea. I made a dupe key for the door and if I lose the drive key, that is a costly matter.

[@msquarehaiti]

I tried and did the chip replacement on my remote key that was not working. It worked very well. Thanks!

[@Lesscoelectronics]

Glad it helped!

[@weblefeck]

I've seen it done where people have left the entire key in the steering column plastics! lol Then they've just had spares cut

[@googleguest4837]

Grow up, Weble! ....huh. You mean someone taped the chip key on the column and used a plain door key to start car ? I tryed that. 2005 grand caravan.

[@BruceLyeg]

@@googleguest4837 worked fine on my 03 F150

[@trinityrussell7932]

Does it have to be the transponder key that came with the car or will and transponder from any key work?

[@halflife103]

why are people complaining so much holy fuck. use this for any 98-08 car. epoxy the transponder under the steering shroud or on the colum right next to the ignition. if that is to much to comprehend then just dont lose your fucking keys =.=

[@glenvere]

Realistic User kk

[@harwoods11]

correct my man :-)

[@clarkfahmy]

wait your saying if you take out the transponder from the key and you put it in another key they will both work?

[@medina5k]

he's saying to secure the transponder near the ignition... then use standard plain metal keys (which are $4-5) instead of the expensive transponder keys.

[@fawkyooo7377]

This is not by passing its removing and placing the chip where the computer thinks the key is in. by pass is making the car start with out the chip….

[@Cotronixco]

He said it's a transponder KEY bypass. He didn't say it's a transponder bypass. Read.

[@skaterslife6305]

Fawkyooo is people don’t seem to know the difference between bypassing a chip and taking a chip out of the key and putting it up by the ignition so the RF frequency is received so you’re Valet key without a chip will work I don’t know the difference between bypassing a chip and removing a chip from the Chi including the chip right by the ignition

[@Cotronixco]

It would help if you were literate.

[@fate2022]

@@Cotronixco actually it says trans CHIP key bypass, implying not needing a transponder key, it's still using a trans. key, he's just now made your car easier to have stolen. this isn't "bypassing anything. Bypassing means not needed, this, you still need the transponder. A more accurate title would have been how to use any key copy for a transponder required ignition.

[@Cotronixco]

You forgot to paste the link to your video, Mark.

[@andyyy671]

Well this video helped and i had a key that didnt work and by having the one with the chip on the same key ring as 2$ metal copy from home depot , saved me from the 170$ new key they were charging me for at the dealer, but true dont leave transponder in car, risks depend on area and car but always good to be safe,

[@Majorvideonut2]

It seems like you could super glue the chip to the column and use any key made for the ignition.

[@Airman..]

you can use a knife to start the car, actually the chip has to be near the key way because there is an RFID amplifier coil sitting around it to energize and read data which is simply i believe an 8 bit

[@ronaldware1921]

Barry Wind

[@skaterslife6305]

Barry Wind yes you can you are absolutely correct .

[@Greydogtech]

I’ve done this to my 2007 Focus, I had to use a razor to shave down the plastic around key and found the chip,I removed the cover from the steering column and once I did that I put the chip near the ignition to find the right spot for it to read it, I put the key in and turned it to start the car each time,every time you move the chip to another spot you have to remove key and put it back in again or it won’t read it, after a trying a few times I found the correct spot to put it, I used gorilla glue to put it on just above the ignition. Did this a few weeks ago and it still reads it and I use a key without a chip.

[@elguapo5467]

Lot of work. Much easier to hide the one good transponder key under the floor mat, or ashtray, or anywhere not obvious, and handy, make as many non-transponder keys as you want, then only use 'dummy' keys to get into car, grab the real key and take off. Of course if you remove transponder key from car and lose it, you're screwed.

[@claztube]

This solution is so simple it eluded virtually everyone. ... I've read all the comments here above yours, you handsome devil you, and then when I read yours, it was like... "BINGO!"

[@tucstwo]

Nice looking key. Beautiful key. One of the best. Wouldn't want to destroy that one.

[@VendettaNC]

Why don’t you marry that key. Jesus bro. Get a room

[@gorflunk]

Why not simply have cheap, non-chip keys made and then open the steering column housing, tape the chip key inside near the ignition, and then close it all back up? That way, you don't destroy the key. If you sell the vehicle or need that key in an emergency situation you still have it.

[@tasmedic]

Your suggestion is about 10,000 times more sensible that what this idiot is suggesting. Well done, you!

[@brycedykes6406]

gorflunk YES!!!

[@taliajones5332]

gorflunk because then if you have the drivers door open it always beeps

[@gorflunk]

Wouldn't it beep if you do what this video says to do? I would find that beeper and disconnect it.

[@taliajones5332]

steve b I don't mean driving! it beeps if you have the door open so every time you get in.the car and out the car etc!

[@andrewp1308]

Good little tip, not sure I would really call it a "bypass” but good idea all the same.

[@tete4life899]

This saved my life 👍

[@heineken1956]

Great idea. I wish it would work for newer "smart" keys. I may just leave the one smart key in the car and then I can use a dummy blank.

[@ifitsgotwheels]

Where's it parked? ;) I have a new screwdriver I wanna test!

[@scottseverin5074]

ifitsgotwheels 2010 Charger

[@luisg8946]

1234 A Lane City NV

[@edluttrell2228]

ifitsgotwheels an aftermarket alarm is cheaper than a new key. So I hope your screwdriver works on handcuffs.

[@matthewjenkins1161]

@@edluttrell2228 Since when did alarms prevent car theft? Only transponder immobilisers achieved that.

[@juliogonzo2718]

@@matthewjenkins1161 do you honestly think a car thief who knows what they are doing is going to waste time punching the ignition on a car that has an immobilizer? They know which cars have them, and which don't. If they are professional thieves, they are going to steal even an immobilized car if they really want it.

[@307rekordzsouthweztrydazcrew]

daammnn..this actually worked... i finally got my car started after 5 days with this process..

[@Angus626]

Good hack, I thought about this some years ago too. ;)

[@msquarehaiti]

I should have watched that long ago. A little donation for you there. 🙂

[@robertkeil2247]

Now any one can steal your car with a flathead, hammer and vice grip. I'm a certified automotive Locksmith and would recommend not to bypass the cars factory theft system. A transponder keys for that Ford is only $5.00 on the Web and most Locksmiths will program for less than $50.00 keeping the integrity of the vehicle intact also that valet Toyota key is also on about $5.00. BTW it is not called a pickup ring

[@taurinenrgy]

50 bucks!? Where I live they charge me 120.00

[@EvendimataE]

Rak Sack i cant believe this guy who is in car alarm business is recommending this :D

[@daNATEP]

Rak Sack i bought a used 2006 toyota corolla with only one set of keys, and they got lost. I now have an uncut key, and an unprogrammed remote. i need to get these both programmed and i have nothing programmed. on the phone the local locksmith people are telling me it'll be about $200, but its just the phone lady and i don't know if i believe her. can a locksmith do this, or does it require me having toyota do it? (toyota would cost me about $600 from the sound of it)

[@EvendimataE]

daNATEP once you got your new key cut....order few cheap ones (about $9) from the internet so you will have some spares....there is an instruction on how to program them, keys and remote, and its very easy.....the only problem is most big hardware stores dont want to cut chip keys anymore if you did not buy it from them....but still you can go to locksmiths where they will charge you about $10 for the same work if they will duplicate a regular key for $3 :D

[@ringtyler]

+Stephen Anthony Wow.. arizona is high.. I just had a new key cut and programmed at my local locksmith for $25 bucks.

[@DACHSCHUND1]

I plan to inst5all a remote starter in a 2012 toyota tacoma. I HAVE INSTALLED ONE IN MY CHEV ASTRO AND DEALT WITH THE VATS SYSTEM. IF I USE YOUR PROCESS ON THE TOYOAA, WILL THE REMOTE STARTER OPERATE WITH OUT THE FUSS OF A BYPASS ? THANX

[@ShawnPeasley]

So how do you compensate for the body control module always seeing the chip? The BCM will constantly be draining battery power thinking the key is in the vehicle. In some vehicles this will trigger random system checks like pulsing the ABS pump or SRS dignostics also draining the battery.

[@templebrown7179]

Not in any cars I have seen. Most cars don't think the key is in the ignition unless it is FULLY inserted.

[@Bawkr]

You have the option of putting the chip into your new key. You don't have to vehicle mount it.

[@vo9111]

So do you need a Toyota transponder for a toyota? Or can you use a transponder from any car to use on any car?

[@barrymorris5028]

My ford truck will not start its been back to the dealer 3 times they have changed the key,the reader ,the gauge cluster .can you make my truck so I can use an old school key no computer shit at all ?

[@Lesscoelectronics]

Barry Morris no, but this is as close as you can get though

[@barrymorris5028]

I have two keys but they will not work .do you have any ideas on what I can do ?

[@Lesscoelectronics]

Id call a local locksmith with the scan tool software

[@barrymorris5028]

Thanks for your help ,but the dealership can't make it work I guess I will just take it out and put in an old school motor something that I can make run.

[@barrymorris5028]

Thank you random I will try that when I get it back from the dealership. Its still under warranty .

[@abd4105]

Is this gonna help a remote starter without bypass module?

[@MrMattMohler]

Bro, just lost my keys at landfill, found out 2 of my 20+ year old trucks was going to cost $90 each. If this works, I owe you big time.

[@thomasmarquez6790]

You can use that chip and another transponder key that is programmed in the same vicinity and will start because I have done it before for a remote start. Where did you get your certification from?

[@dsldsl6460]

LOL bypassing means working something around not setting something on forrever I mean bypassing a password does not mean that you make something that types that password for you every time you want to access some account

[@MusicByJC]

I have a 2004 Toyota and I broke the key with the chip in it. I have a non-chip key that I use and then I touch the broken key with the chip to the key in the ignition where there is metal showing at top. From my experience it seems like I have to make contact with the key for this to work. This video is describing a technique where you just have to get the chip close to the sensor. Maybe my key works in a different way. I will play around with it to see if just having the key near will work. Any thoughts?

[@scottfink350]

Sweet. Thanks.

[@barnes29510]

I'm changing the whole column with a different key. Can I take the chip out my old key and replace the chip from the new with it??

[@JervaughnLewisRio]

Congratulations! you have now exposed yourself to your vehicle being stolen

[@kerimk2306]

How did you manage to open up the key? My spare Peugeot 107 key has no buttons. This spare key has no screws to unscrew unfortunately. I'm trying to open up the case by using a prying tool (used for IT) that looks like a guitar chip), but I can only do that 'temporarily'. Like it doesn't want to open up completely. It closes back right when I try to slide all the way around the key. Do you have tips for me?

[@1SSA1cosmoprower]

That is a damn good trick XD wish I did this with my 02 Dodge neon haha

[@tigger126]

Will you still be able to use the power door locks or will the system think that a key is still in the ignition and not let the doors lock?

[@emily1]

The key has to actually be in the ignition to trigger it as so. Having the transponder chip only unlocks the immobiliser and allows the vehicle to start.

[@davidjeffery6402]

dodge dealer wanted over 500 bucks for a new key for a 2010 dodge ram. I'd burn the truck first .

[@greglong6702]

David Jeffery

[@greglong6702]

Dids you ever have any luck with your issue?

[@drkastenbrot]

David Jeffery sounds like a fun joyride then

[@michaelmongelluzzo1348]

There should be after market company’s to buy the key from. Then go to your local dodge dealer give them proof of owner ship and they have to give you a vehicle PIN number 4 digit code. Find a shop with a scanner capable of programming a key. You should get out of this for 200 bucks. Dodges are super easy.

[@artman102]

@@michaelmongelluzzo1348 AutoZone has $59 aftermarket kits for most cars.

[@Visilicious]

I totally lost track of what you said towards the end. So what do I with the transponder in the key? Put it in a toolbox in case I ever want to use it again? So the car will now start without the transponder?

[@richardshort3914]

Thank you. I wish I'd seen this earlier.

[@davidm9214]

So I'm wondering if I do this, will a 2 way remote starter system work on my Jeep wj

[@luvstruck2733]

OK it gets the job done, even though it is not a true bypass. You can analyze all day and talk about being able to program a GM computer, and this is not a true bypass. You do have to admit, it gets the job done, and if the ad had said something like how to make sure your car starts every time, and eliminates your bypass anti theft system, you probably would not be able to get all of that in the space they give you to put in the title of the video. So give the guy a break. No I do not know him, and have never had any correspondence with him. If it does the job, get it, if it doesn't, then don't buy it. This is easy stuff here.

[@googleguest4837]

Luvstruck ok. So why cant i start my grand caravan with a door key and holding the chip key on the ignition column ? It only starts for 3 seconds.

[@lostjalopygarage8150]

Great video! Will this work with a valet key?

[@r.broderick2222]

Doesn't this also trick the car into thinking that you have left the key in the car? Wont this screw with security systems and engine mobilizers or even not allowing you to lock your car as many cars will not arm or allow locking if the key is in the ignition? (Or in this case, transponder?) You could ruin an expensive key if not careful.. I'd recommend you have a cheap key made, and tape it in the approximate area of the cylinder and see what affects leaving that key / transponder would be BEFORE hacking a nice, expensive key.

[@Jacksonjames4]

+Raymond Broderick no. has nothing to do with security. all it does is allow the car to start. once running, doesn't matter where it is.

[@TheMakyato]

+jack you are so wrong in many cars not older than 10 years you may have problem if the key is in the car or in proximity ( less or more 10 feet) you cant lock your doors (from outside) if the key is in the car and if nowbody is in the car after 5 min the alarm is start your black box will see always the presence of the key this may vary from car to car optional you buy and country in my outlander 2008 if you have the parasolar open you could not lock the dors an many other things

[@Jacksonjames4]

+TheMakyato no, actually im not wrong at all. We weren't talking about proximity keys. These are different. The instance the vehicle starts, it stops communicating. Prox Keys communicate differently.

[@TheMakyato]

+jack i agree that is totally different but this is not bypassing and it can have security and insurance issue even if is practically very small risk the insurance company will use this against you this is maybe out off topic but many machinery/equipment use same type of key and the risk is much higher i have done this and i will doit again if necessary

[@igor6969]

+A MTS Hardware stores don't have chipped keys. Must get them from dealers. Couple hundred dollars. Some of my customers keys cost $400+

[@korvtm]

I 2001 company I worked for bought some Ford pickups with the transponder keys.Company ordered each truck with 3 keys.folks out on the floor wanted more keys,found out that they could order keys through Ford then use the programming steps in the owners manual.What they did not know is that the onboard computer on the truck would lock out if they tried to program more than five keys to the truck.Funny as hell to see the truck with less than 5000 miles on it being towed back to the Ford dealer so they could reprogram the computer and get three keys that would start the truck.Crew learned to live with three keys after that.

[@hamper53]

I am dumber for having watched this.

[@dtcromer]

Quick question, I changed my ignition barrel over and it came with a key that has its own transponder chip (2000 series 1 Camry), should I change the chip over from one key to the other to start it? Thank you for the video

[@GFlCh]

I would say you should use whichever chip allows the car to start.

[@citylockusa]

Daniel, the old lock could have been repaired, Toyota was known for split wafers that hang up. This way, same keys would fit all locks, and you would have not bought a new one or had a programming question. Though this thread is technically correct, I do not advise this as a money saving effort. When you have a future vehicle electrical issue, the mechanic will be charging you an hourly fee to undo whatever makes the vehicle behave other than how it is designed. For example; If when brought into shop with a problem, there is no theft light intermittently flashing, and vehicle does not start because of an ecu issue... the head scratching will begin.... at 90.00-175.00 an hour! Your key can be decoded, fresh keys made and programmed reasonably. Bypassing can ultimately get expensive. We do it the proper way, no clone or cheap fake chip keys. I am all for saving money. When we cut and program one keys for a car, we offer a steep discount on additional keys made and programmed at the same time. THAT is how to save money, without trashing out a fairly effective anti-theft system.

[@dtcromer]

Thanks for the input, I took it to Toyota Geelong and for 60$ it was re coded

[@ijustinw]

Jeff Rosen what if the car is a piece of shit that is probably only worth 100 bucks?

[@marcmarcmarcmarcmarc]

ijustinw use the $100 and buy a peddle bike

[@ysman3]

Now I can steal your car with a screwdriver

[@craigdavis9766]

I have two keys for my car, i want to install a remote start before winter hits. Can i do this to one of my keys? Would having two transponder chips close cause problems?

[@Jackcc5]

i can see the point for doing this but isn't it better to not do it. I mean that makes your car easyer to steal that's why the Vehicle anti theft system was created. i would much rather pay the money and get another key and have the anti theft system working then not.

[@ponybrony4886]

$500.00 + to get another one!!!!!!!!!!!!!!

[@elslockmithservices]

Pony Brony Only if your car is a Saab might cost you that much. That is the only car that I think would cost that much for a duplicate. Not even a Ferrari or VW, Mercedes They might cost 95.00 just for a plane key that has chip + a full Insurance Liability would not cover any of a stolen car with an existed so call "by pass" after all, they were the ones to requested the dealers and anti-theft system since some of their customer were scamming insurance by robing themselves, if you have a bad remote start installation on a anti-theft, your insurance will denied any coverage since you gave up the only secure to a car thieve.

[@elslockmithservices]

***** I'm wrong about what? Those keys without a chip would go for around 50.00 in our shop. That's a pretty fair price. The insurance companies do investigations specifically to find out whether there was a bypass, an after market remote starter, or an immobilizer turned off. For cars of course only that have chips and have full coverage insurance.

[@mozzmann]

***** Well lets see Original Registration, Chassis and VIN Number's on your insurance paper's etc. Oh and an engraved placard attached to the vehicle in a spot that only I know about. Why you would want to bypass in built security is beyond me.

[@TheBlueSmirk]

mozzmann Saves a lot of hasstle programming chips for new keys. I have a Honda Civic and can't connect to my ecu to program the key so this is a good way to do it.

[@gregorypiercesr.794]

i have a 2010 ford ranger and any key transponder will work to get my ranger going again since i lost my original key?

[@goldenboy5500]

just don't tell your insurance company because they will void your fire & theft also if your buying from let's say a Toyota used car dealer insist on a spare chip key or you can go to walmart and for less than 40 bucks have a key cut & programed If you loose or damage that tiny chip it will costs hundreds to get a new key and program the whole security system

[@Discreetsecuritysolutions]

Absolutely right - this invalidates your theft insurance in the same way as if you left the key in the glove box. It's a stupid "bypass" only done by unscrupulous locksmiths and witless car owners.

[@TheWorldgonecrazy]

Although to be fair criminals know they have these transponder keys,but they will not know you have done this to you vehicle so car owners are still safe.

[@Bawkr]

Who pays for that kind of coverage anyway. Liability only all the way. Save up the money you would have spent on insurance for a replacement vehicle.

[@suprola7961]

What does the key look like under the white plastic? Does it have a hole through it?

[@TotoGuy-Original]

thats not really a bypass though is it. its just a bodge job! and also would invalidate your insurance if the car was stolen. i could have made this video 30 seconds long

[@gregorypiercesr.794]

will a standard magnet work or does it need to be from a key?

[@Lesscoelectronics]

it has to be proprietary from the key

[@jamesbarratt593]

Interesting but you could have said it so much faster.

[@paulobparaujo]

Hi there, nice video! I have a toyota key just like that one but more recent (2018). Could you tell me if those keys only with the transponder chip are waterproof? For example, to go surfing? thanks!

[@christopherhazelton5436]

This in not a bypass

[@mikehaase4938]

Thanx a lot. You gave me the information I needed. I still need the Old Key for the Door but I just hold it close to the New Key when I start the engine. Thanx again. Bill not Mike.

[@e.imccool8993]

can I do this on my horse?

[@LesNash1]

e.i mccool m

[@mikeo.g8809]

e.i mccool my horse i like that

[@MattyVanFossen]

Can you convert to a flip style key doing this?

[@denversecurity63]

Yep, as a locksmith that programs these transponder cars, let me first say that this is a dumb idea for security reasons and second you don't have to cut your key up unless you just don't have a life. you can just drop the shroud and tape a key to the reader ring. Then it will be even easier to steal your car. Or, why not put a sign on your car that reads "Please Steal Me" !!!!!!!!!!!

[@richb7414]

No different than owning a 1995 or so older vehicle that has no anti-theft at all!

[@c0gsinc0gs]

Cars didn't have these transponders for most of my driving life and I never had a car stolen. Maybe if I lived in a high crime area I'd fell differently but I just lost a key (and a fob) and all I see these things as is a way for car manufacturers to soak you for a hundred or more bucks for something you used to be able to get for a couple of bucks at any hardware store. Just a scam.

[@helivesonforever]

Mor Bid Door locks my friend...

[@abayer1000]

c0gsinc0gs I agree this should be a option it is a bigger pain than it is worth

[@jefris]

This is a bs. The only thing that can convince me is if your your house key has transponder. Transponder key is a way to rip people off just like the engine light in your car. Not always need to be concerned. Back to basic people where there's no transponder and bullshit.

[@tonytone2239]

thats not a bypass, what youre doing its just a relocation of the transponder DUH!

[@stuartbeard1899]

this really does work thank you so very much

[@kdmc40]

This is not a bypass! you're just leaving the xponder there all the time.

[@twoeightythreez]

kdmc40 on some cars this will result in excessive battery draw...because the control modules wont go to sleep...hope you enjoy dead batteries if the car sits for a week

[@orangestoneface]

might have it movable so you can hide it in a secret place int he car

[@rokitman5753]

kdmc40 whatever buddy atleast it works 😊

[@Throefly]

@@twoeightythreez Most cars don't check for the transponder-key until the ignition switch is turned to either ON or ACC, so this will only apply to *some* of the first gen transponder-based security modules, which are extremely rare at this point.

[@Cotronixco]

He said it's a transponder KEY bypass. He didn't say it's a transponder bypass. Read.

[@justjayjustjay5054]

So I have a question for you... I have an old key like the one pictured for a 2001 F150 that uses a 4C chip. I'd like to have a key fob with a flip out key, however there are none with a 4C chip available. I have found a key fob with flip out key that uses a 4D63 chip & suplosedly the remote part works for my vehicle. Would I be able to take the 4C chip out of the key, and place it in the key fib instead if the 4D63 chip and have it work the same?

[@robertpainter2937]

Why not just use a key box and install a key into that? This information is a little deceptive making people believe they are bypassing the system, when n fact they are not.

[@keenanleetodd]

+Rob Painter Bypassing the cost of chip keys.

[@TheMakyato]

+IKnowYourCommentIs good point of view

[@keenanleetodd]

It's usually magnetic and you put a key in it under your car. I use wire and yes you will get dirty getting your spare key. You have to decide dirty clothes or lost time and money getting a tow truck to come.

[@robertpainter2937]

A key box goes under the dash. A working transponder key is put in the box. A wire is run up underneath the shoroud on the steering column and rapped around the transceiver (antenna that sends signal to computer telling it correct electronic key is being read to start the engine. Key boxes are used by auto alarm stores that install remote start. You do not need a remote start to employ one of these key boxes. However, that is how the car starts with no key in the ignition at a distance.

[@robertpainter2937]

So it is not what knowyourcomments is referring to. He is referring to a hide a key. Completely different scenario.

[@eduardofeliciano7850]

I have a question , i lost my original key with chips on it , and i went to the dealer center and ask them to make me a new key , its a transponder key, and when I arrived home i tried to start the car but it didn't start , yes i have a power and everything, battery is good, how can avail back the original key with chip ? Coz I can't have it program without the key with chips.

[@billyharrison6729]

You haven't "bypassed" anything!

[@chrisquinn6225]

Bypass is just a fancy word for gitting around it.

[@HM-ke1qm]

You bypassed me the other day on the road.

[@YerBrwnDogAteMyRabit]

​@@HM-ke1qmMe too! Except...I was only going like 4mph, so I understand why...

[@csorrows]

Exactly. But nothing here was bypassed. The chip is still required hence not bypassed.

[@YerBrwnDogAteMyRabit]

@@csorrows Oh, it can be legit bypassed alright, not a manufacturer's chip in sight. You're watching watered down, sterilized and censored KZbin tho, so it's highly unlikely you'll see it here.

[@powerfullengine50]

if you used a transponder from another car key will it start ? or each transponder is different

[@sailort800]

No, each transponder has a unique ID programmed into it.

[@powerfullengine50]

Patrick Ryan thanks for replying though

[@motorkeys]

This video should be called how to make your auto insurance nil and void.

[@wholeNwon]

+auto locksmith Null and void.

[@oni_goroshi]

You must make a killing off of programming fees by fear mongering people.