Magvent MV-90 Dryer Vent in Dryerbox Installation

[@cypilotiowan4761]

This is exactly the install we're doing this week. Thanks for the video. MagVent is just a great product.

[@video4belphotos]

OCD me…. I would have caulked the connection going outside. Caulking is the carpenters eraser. Caulking will keep bugs and vermin Out. Otherwise one of the best DIY videos I’ve seen in a long time. Job well done! 😊

[@mpxz999]

I just installed my mv90 outside of a dryer box, because of a concrete ledge on the bottom corner of the floor behind the dryer (so it couldn't fit in the stud bay). It was simple to use even one tapcon screw on the mv90 positioning bracket to make it position right where it was needed! After that, the magvent linned up perfectly with my dryer duct! I should say to TEST MOVING THE DRYER IN **AND** OUT. Why? To test and retest both the brackets connection to the wall And To test the hold of ring clamp, holding the end of the magvent part ON THE DRYER. I emphasize this the way I do since I had to tighten to ring clamp on the dryer much tighter than I expected to achieve a solid hold. Anyways, when all is said and done, it really does work perfectly, and looks pretty damn good too. It's around $95 Canadian to get one of these, but so so worth it. Thanks for the fire caulk advice btw! I was just going to use foil duct tape alone before seeing this. Great video!

[@ronkelley1476]

This is really helpful. Looks like we finally have a solution to get the dryer very close the wall and eliminate the hassle with the hose.

[@stacymontgomery300]

My dryer vents straight out. It is up against an outside wall of a very old house. 1915 aged house. Have alot of lint dust in the house and have had a repair man her multiple times still have lint dust. The washer and dryer and not even 3 years old. Bought the set new. The dryer sits out 3 inches more then the washer. Wish this box could lay on its side. Want to move th dryer to a different wall and move the washer also. But the box would still have to be on its side due to a bedroom above the laundry room. Love this old house. The pervious owners were very old and moved the laundry upstairs from the unfinished basement. Who ever did the work slapped it together. The washer has 2 different hook ups. 1 coming up through the floor that looks to be 60 yrs old. Also has a wall hook up. How ever that one I guess is for looks because it's not even plummed in to be used. Was nice shower when installing them to the newer wall hook up only to fnd out the floor hook up was the only working one when we turned the water on. Good times!!

[@johnmassie1273]

Great install video. I currently have a hose hanging from my ceiling that vents Thur the attic outside. I plan to strip the wall to stipends and install in between the studs like this product. Exceptional video and professional finish.

[@samsonevickis]

Wow, very cool. Just bought one.

[@MagVentLLC]

Big shout out of thanks to Nate at NL Productions for making another quality video, Cliff at Innovate Dryer Products for providing the DB350, Mr. Bewley for providing the shoot location, and of course Angie at MagVent for making it all work.

[@curiosity2314]

Looks good but the larger question would be why a dryer box would come with an oval hole for the pipe?

[@DONALD-MAGA]

that box is made for a 2x4 wall which is only 3.5 inches deep. The vent pipe is 4 inches so it requires some crushing to fit.

[@mesomebody5017]

We bought a new house that uses that in wall dryer vent but it is NOT inline with where my dryer’s vent is-so I need to MOVE the dryer box over one or two sections of 2x4? This laundry does not have lot of spacing between sink cabinet and w/d. Plus there is door to the HVAC unit closet across from dryer that opens OUT-so dryer need to be as close to wall as safely can…. Is this something an appliance repair person could move and reinstall? Or does it take a drywall guy for the Sheetrock repair?

[@wayneguy6043]

Will some air be lost between the magnets?

[@AlwaysBeeCool]

seven years later...is that old dryer still running....boy it was heavy wasn't it?

[@KrazyKajun602]

Why don't they make a dryerbox to exhaust straight out the back of it and through the outside wall?

[@frankrizzo7307]

Question. Did you use regular 4" duct in the wall or was it oval pipe?

[@customerservice9263]

This install used a standard 4" duct. Sometimes during the install you may need to oval the pipe a little by hand to get it through the dryer box.

[@johneverett957]

That was my question as well. How did you get 4" pipe to fit in a 3.5" deep wall cavity.

[@DONALD-MAGA]

@@johneverett957 to fit a 4" pipe in a 3.5" wall you have to make it oval.

[@raymondlayton7305]

How did you go through your 2- 2/4 top plates and meet code?

[@TankGunner84]

That’s really nice I repair sell and install appliances and I’ve never seen this... I just don’t see a lot of people wanting to spend the money especially in homes that are already built and occupied.

[@SuperJeremi10]

I wishbincould have this in my home so i can oushbthebdryer back more i cant push mine back. It vents staight threw an exterior wall.

[@MagVentLLC]

We do offer some special vendor pricing if you are ever interested in becoming a certified installer :)

[@mmullen2112]

This is a great video about a great idea! One comment though, the screws are self drilling, not self tapping (different fastener). 😉

[@johnmcbride364]

I wondered whether anyone else would make this distinction. They are indeed different fasteners.

[@offplanetevent]

Why didnt you " pack out " the other side of the box?

[@kevpkelley]

Just mounting the box to one side and the bottom makes a really solid attachment. We could have chosen to pack out from the other side, but I think it was closer to landing in the proper location on the left. So, to go from the other side would have required more layers of material. Thanks for watching.

[@davidmcneill3809]

I'm getting ready to remodel my laundry room. The original installation has the dryer vent in the floor causing the dryer to be several inches away from the way. Since my vent goes down, not up as in the video, will this system work? I really like the magnetic link.

[@MagVentLLC]

The MagVent MV-90 is designed for when the vent path takes a 90 degree turn to the side, up through the ceiling, or down through the floor such as in your case. The MV-90 is designed to be installed directly behind your dryer's vent, and can tolerate an offset in vent alignment of up to 3 inches. I encourage you to view our MV-90 installation video on our website! With your installation, the tail of the MagVent will be pointed straight down, and if you have a standard height dryer, then you should not need any additional rigid metal pipe to complete the installation. Please don't hesitate to contact us if you have any other questions or if we may be of further assistance!

[@stephenwatson584]

I know the dryerbox is not your product, but do you know what is the reasoning for having a oval-shaped opening instead of a circular (round) shaped opening at the top of the dryerbox?

[@calebdrake3544]

That's usually done for a 2x4(db-350) wall or using larger dryer tubing...I think the 2x6 version(db-400) isn't as oval as the 2x4 version.

[@minnesotadryerventguys]

So not an air tight connection? is it safe for gas dryers ? (don't want carbon monoxide leaking) Also what about the magnets attracting bobby pins, pens, money, wouldn't that clog or cause the debris to help form a stop with the lint.(kind of like when there's a bend in flex piping or top mounted lint trap on the dryer) (if you take dryers apart you know there's almost always debris at the bottom of the top mounted lint trap) just some things to think about for the engineers. Would have like to see this as a fresh install where there is already finished walls, because I know it's twice as hard to install these boxes.

[@customerservice9263]

The connection is air tight and yes it is safe for gas dryers. As far as the magnets attracting bobby pins etc. , yes it is possible but the main lint trap should catch most of these items and we have yet to have any issues or customer complaints about this happening. If this were to be an issue, as you mentioned it happens with regular flex hose, the MagVent makes removal of a restriction a lot easier as you do not have to deal with getting behind the dryer to disconnect and reconnect the hose. We would love to shoot a video of an installation with the drywall already in place, and we hope to have that content available in the future. Thank you for your feedback.

[@minnesotadryerventguys]

@@customerservice9263 was just curious about that, I haven't ran into any of those yet. And my apologies was not trying to discredit it just wondering about that because, when I think about the carbon monoxide getting out, some of the people don't seal the vents sometimes so that's what I worry about it. A good product though!!! Good job I'm coming up with something so revolutionary for dryer installation.

[@customerservice9263]

@@minnesotadryerventguys No problem at all. It is definitely a valid concern! We always strive to make improvements and ensure our product is safe for all users. If we can be of any help in the future don't hesitate to reach out.

[@pasad335]

The dryer is basically a giant exhaust fan for the laundry room. Even if any CO did leak from the magnetic joint, the dryer is just going to suck it right back up and vent it out.

[@greg.montelione]

...would have been geat if you were able to show the complete install up through the ceiling. I'm curious to know how everyone is getting the 4" duct through the top plate. I have metal stud framing and it's a real doozy getting the pipe into the tight space of the attic to vent through the roof. It also seems that it's almost impossible to adhere to the letter of the code when installing dryer ventsin an older these days... especially if you're laundry room isn't on an exterior wall 🤦‍♂

[@bryandiel6773]

will the magvent seal be airtight, or will some lint leak out?

[@farmer864]

the end of the male end is fluted, or tapered lip if shall say, it creates an inside seal.

[@arthurenloe3679]

Is this pretty easy to pull apart the magnets, when you can't get behind the dryer. I've looked at a few videos and none of them shows this being pulled apart.

[@greg.montelione]

You need to leave a little extra flex to pull the dryer off the wall in order to separate the magnets. You don't want them to easily separate.

[@sandycash9837]

Can I use the mv90 to vent thru the floor vent already installed?

[@MagVentLLC]

The MagVent MV-90 is designed for when the vent path takes a 90 degree turn to the side, up through the ceiling, or down through the floor such as in your case. The MV-90 is designed to be installed directly behind your dryer's vent, and can tolerate an offset in vent alignment of up to 3 inches. I encourage you to view our MV-90 installation video! With your installation, the tail of the MagVent will be pointed straight down, and if you have a standard height dryer, then you should not need any additional rigid metal pipe to complete the installation.

[@fiouable]

What happens when you pull the dryer out? The flexible conduit tears appart?

[@customerservice9263]

The magnets actually release with 5-8 lbs of pull force. Sometime the flex hose slips off of the dryer vent, so we recommend wrapping the dryer vent with some aluminum tape to add texture for the hose clamp to grip.

[@trulysurprised-bk7cy]

The heat alone from a dryer fire will burn those studs.

[@fiouable]

Man that oval thing is a pain

[@francinelafontaine4828]

Men IT'S ok when both hols are facing each other. But mine is diffrent . First OF all , I live in an appartment . MY dryer hole 's center is at 14 inches , and the hole in the wall is mot in front OF my dryer. So since y landlord gold me that tête was some magnet -vent ??? I whant To know more about it . When you show exemple on video ??? Or dotés mot helping me at all ! I with I couple sens toi a picture , OF the back OF my dryer. Wich I really dont like it at all ! It is a fire trap . Van toi help me ???

[@trish5119]

How to install a dryer vent hose

[@cyhomer]

I wanna see someone pull the dryer out and see what happens after the magvent has been installed...

[@lquinn7212]

How about no box?

[@MagVentLLC]

Here is a link to an install without the dryerbox. kzbin.info/www/bejne/qJW1gZWGm9qGZtU

[@fluffymittens24]

Let's see, number cause of residential fires, so let's change the route of the vent from horizontal to vertical. Since they are now vented on the roof no one will ever see or think about it until it's too late.

[@bryandiel6773]

@@cmmartti But builders started putting dryer vent runs through the roof instead of out the exterior wall. These vertical runs have more lint buildup because the ducting goes through the attic. the heat of the attic causes condensation in/on the duct causing mold and wet lint. Wet lint will clog a dryer vent. I wish my dryer was on an external wall!!

[@stuartcampbell9937]

Could do without the annoying music playing the whole time.