Making a Mini Hydraulic Pump

[@billdoodson4232]

What a nice little tip that is with using the circlip in the lathe chuck to locate the piece for machining. I'm going to have to buy a selection of circlips now!

[@metallantik]

😃🙏🙇❤️

[@davers1610]

Agreed. Love it.

[@jacqueso8424]

It is a good tip yes. But it should be enhanced a bit by using a clock indicater and a magnetic base set to hold finger clock and try to set the workpiece more accurate. Otherwise a very good video afterall and im impressed as to whats being achieved there

[@markrainford1219]

Nifty

[@sto2779]

I saw him doing that, didn't make sense how it was helping him. Can you elaborate more on the usefulness? Thanks.

[@thecorbies]

I've been around lathes, mills and other workshop kit for nearly my whole life and I've never seen that circlip trick before. It's fantastic. I love it. It's so simple. I will definitely use it sometime soon. Regards Mark in the UK

[@АндрейГ-д8о]

Читаю коментарии и виду что весь акцент направлен на стопорное кольцо. Я думал что я один из не многих кто незнал этот лайфхак. А оказалось таких как я достаточно. Я тоже за все время просмотра ютуба впервые такое увидел. Никто так не делал, хотя наверняка есть такие люди. Сейчас думаю во многих роликах это будет показано так как многие друг у друга набираются опыта. Я тоже обязательно этим воспользуюсь. Спасибо автор.

[@miladalipur2563]

Excellent and beautiful, you are unique😍😍

[@MrPhatNOB]

The circlip idea was awesome!

[@metallantik]

Thanks 🙏

[@AlexAlex-ll5sz]

Использовать стопорное кольцо прикольно придумано👍👍👍👍

[@metallantik]

Thanks 🙏❤️

[@robocad3d]

Лайфхак с кольцом в патроне, в который упирается деталь, просто зачет 👍

[@janismekss]

Use of circlip for positioning of part in lathe, is a amazing idea😮

[@metallantik]

Thanks a lot 😅🙏

[@Your_Friend_Corey]

As soon as I saw it I assumed that's what those slots were for and was wondering why I never see them. Then I saw this comment.

[@АндрейГ-д8о]

Согласен

[@hda1010]

Very nice. Your pump has no ball bearings, so don't apply radial force to the axis with that chain / gear. Use direct coupling to the motor.

[@ИванМихайлов-я2р]

Автор молодец, спасибо за совет тоже буду пользоваться стопорным колечком для базирования детали в токарном патроне👍

[@metallantik]

Thanks a lot ❤️🙏

[@владимир-л8в3э]

В насосы такого типа не ставят пружины под лопатки, они работают за счёт центробежной силы. Меньше трения на лопатки, более свободный ход.

[@skunkjobb]

Nice build but you need much much higher precision if the pump shall give more pressure than a couple of bar. My powersteering pump is of the same type and when it failed I bought a new one but I took the old one apart of curiosity. I couldn't even see any scratches but it had lost pressure anyway. The wings need to be very tight in the hub and the inside of the housing needs to be ground and polished. The smallest gap or scratch and the pressure is lost.

[@metallantik]

You made an accurate point 👍🙏❤️

[@morwin3998]

Interesting way to register your work, quick and dirty. I'LL have to try it out.

[@ImWatchinYou]

Reminds me of the time I invented this very pump design back around ~1985 only to find out a few years later it had already been invented a long time prior and in wide spread use. I find it amazing how the same things can be thought up by many different people over time.

[@metallantik]

Exactly, I thought this was my idea, then I realized it was invented before me 😃😃🤦‍♂️🤷‍♂️

[@Enigmatyr]

Makes you wonder how many modern inventions had been utilized by ancient peoples but lost to time

[@PaulBoscott]

Using the circlip was new to me I will have to get a set Thank you

[@siirousshahkaramii8628]

sehr schon perfect vielen dank fur tecknik du gut machen arbaiten dugute

[@metallantik]

🙏

[@Asbalthazar]

بسیار خوب❤❤❤

[@metallantik]

❤️

[@TrungLe-i5x]

Phót bơm thủy lực..mua rẻ ơi là rẻ.. tự làm ra mỗi cái.. tính theo giờ.. có thể mua năm mười cái..xịn .. bền tốt..hi...hi...

[@davidkarath6549]

Convert your lathe to a horizontal mill for your slots..

[@Themulchand]

Thanks you. I got concept of hydraulic pump 🙏

[@metallantik]

🙏

[@Xhydraulics]

Making something like this is very hard. You are a skilled person ❤

[@metallantik]

Thanks ❤️🙏

[@newagerc5356]

I agree i have a selection of snap rings or circlips I’ve never seen that before I’m trying this thanks

[@Nash_son_of_Zeus]

I really hope you sent this to the phone manufacturer. Lol. However, I will be using this to help me design a few things. Thanks, Brother!

[@CMAenergy]

Well done But there is another way to get more accuracy when putting those piece in the lathe I blotted some aluminum rod in between the jaws, and when I go to use it without the jaws in place, I machine face it, they are removable, And if he did not have a mill He could have held that center piece on the carriage on the lathe and used a milling bit or even a drill bit to cut a real perfect slots .

[@stefang1087]

This hydraulic pump will definitely work. It is a well known one, but because of materials used and the lack of surface treatment of the pump house, it is just a matter of time until the hydraulic system will be damaged, because of the small aluminium shavings.

[@metallantik]

Absolutely correct, thanks a lot ❤️🙏

[@Diy_Cnc84]

You have great ideas. Thanks

[@Kargoneth]

Adorable little vane pump. Well done.

[@Kargoneth]

Hmm... not much holding those vanes in the recesses.

[@metallantik]

Thanks a lot 🙏

[@kumadinielectric5500]

Idea Is awesome. But, ek hydrolic pressure banane ke liye 20 hazar mobile kon tut ta ?

[@metallantik]

Thanks ❤️

[@DML2024]

Excellent pump.

[@CoolIdeasDIY-qv1nz]

Interesting😉

[@metallantik]

Thanks🙏

[@electproject]

Nice skills friend

[@metallantik]

Thanks ❤️🙏

[@Matthews_Tools]

Great content! Keep going

[@MinhQuangNguyen-io7np]

Chăm chú xem đến cuối cùng lại đi phá hư cái điện thoại, vậy lấy cái búa bụp cái là xong cần chi mất thời gian quá.

[@chongshenchang9367]

The test subject was a tough one.😅😅😅 Nice build.

[@Shedevrika]

Молодчина! Руки с правильного места растут и голова работает!

[@metallantik]

Thanks a lot ❤️🙏

[@Shedevrika]

@@metallantik Вам спасибо, за то что делитесь своими навыками!

[@Свят-ч7м]

Чувак с лобзиком ты здорово придумал 😅

[@vahideh.sh18]

You are very smart and skilled 😍

[@metallantik]

Thanks 🤩

[@cheetah.motors]

Very informative thank you ❤❤❤

[@KiloFeenix]

Now you need to make a couple drive motors so you can make your own lawnmower.

[@albertoramonacosta1212]

Impresionante es una bomba de verdad se puede subir agua a un tanque con un diseno mas grande gracias Argent

[@RixtronixLAB]

Creative video, thanks :)

[@metallantik]

❤️🙏

[@DeVs51]

Très bonne idée d utiliser le cervlips merci pour ton idée

[@metallantik]

🙏❤️

[@gadgetdeez7069]

Love the fact you flew clean past the tolerances for the vanes, and installed the oil seal backwards. You can always figure out which side is the side that fluid is supposed to be on by the easier of the 2 ways to install a seal on a shaft. Lip always faces higher pressure.. 😂

[@parnuzutech]

Awesome 👍

[@metallantik]

Thanks 🙏

[@fatrobotnew]

Awesome. You should definetly buy a mini mill.

[@metallantik]

Thanks a lot 🙏

[@spehropefhany]

For an vacuum pump (desoldering tool) I've seen a similar design but using graphite (carbon) vanes.

[@_Radu.G]

Super pompa , ingenioasă fabricarea ei, dar pâcat de telefon.

[@metallantik]

Thanks a lot 😅

[@leila7963]

amazing 😍👌

[@metallantik]

🙏thanks

[@VanderleiBertoso]

Só pelo anel elástico como stop já valeu 1000 like

[@okanvitaliy]

Насосы с таким принципом работы используются в автоматах газводы. Они итальянские, стоят под 300 баксов. Могут делать давление 15 атмосфер. Правда у них полость из пластика и стираются они быстро. Этот навряд ли сможет создать высокое давление

[@Bakhamaster001]

Күшті насос екен уйге қажет май құйған ға

[@blackIce504]

I like the design especially when impeller is so simple but i was thinking with your use of springs, if the impeller was spinning at a high RPM would it still get a good seal as the fins be thrown out towards the side of the case similar to an pneumatic motor.

[@interhaker]

Yes,youd get both the springs and the centrifugal force throwing them out

[@svsc89]

have you messured the pressure the pump is able to generate?

[@akbaryavash]

Nice 👍🎉😂 یه چه مسخره بازیه فندکمه بیار 😂😂😂😅

[@metallantik]

Akbaaar slow 🤣🤣🤣

[@akbaryavash]

الان آخرشه دییم یه گوشی مه قورتنیش د یک اینارو دیگه مترجمم نمیتونه ترجمه کنه😂

[@metallantik]

خخخخ

[@PeaceDeath.]

Перекачивать воду из емкости в емкость пойет, но не для создания высокого давления.

[@davidjames1007]

Fun project, nicely done

[@metallantik]

Thank u so much 🙏❤️

[@Rollie396]

I would love to do that to my cel as well!lol

[@metallantik]

🙏❤️

[@BuilderFrank]

👍👍👍👍

[@metallantik]

🙏

[@СергейЕгоров-ы4н]

Теперь я знаю как разобрать мобильный телефон))

❤ sao mà hay quá dị.

[@ace-tv4hi]

Not much good for hydraulic pump but would make excellent suds pump for lathe coolent!.

[@metallantik]

👌❤️🙏

[@bcung5233]

Very good

[@sto2779]

Incredible, very skilled and talented to make your own rotary vane pump, gives me inspiration to make one. Would be nice if you can make a 2 stage vacuum pump. 10:14 - Is this a mechanical seal? Where can I get one? thanks.

[@rezadrvishi3665]

It was interesting❤❤

[@metallantik]

❤️🙏

[@CristopherPerdomo-nd3jj]

noooo el telefono ,amigo esta bien lo que iste y me impresiono pero el telefono no ,si👍

[@rubenprovencio-b1u]

Hola donde puedo encontrar planos de la bomba hidráulica

[@Behnia_rj]

Nice 👍🏻

[@Bigredkarl]

what determined where the inlet and outlet go as i would have thoungt the most open portion of the pump and the most closed

[@angquangloi6a525]

Motor quay 5 lá sắt tự văng ra chứ cần gì phải lò xo

[@fetterAnonymer]

Gut gemacht 👌

[@metallantik]

Danke schön 🙏

[@Guds777]

Probably cheaper to buy a pump rather then buying a lathe, mill and all the rest to make to pump... :D :D

[@borjaalbanell2312]

Hello, I really liked your video, what is the name of that type of anti-gas bearings?

[@odin823]

what is that piano wire in a coping saw? great build btw.

[@siirousshahkaramii8628]

Das schon berawo❤❤❤❤❤

[@metallantik]

Thanks 🙏

[@akbaryavash]

Very nice 😂

[@metallantik]

Thanks bro 😁

[@vahideh.sh18]

Das gefällt mir super 😍

[@metallantik]

❤️🙏🤩

[@Hamid-az]

Everything was fine, only if you had touched the contact surface of the aluminum parts (5 pics) with the inside of the main part, the pumping power would have been much higher. That is, you would level the parts with the inner radius of the cylinder. I hope I got my point across❤

[@metallantik]

Thanks for the tips, I will definitely use your advice ❤️🙏🙇

[@jaffasoft8976]

@@metallantik In my VE Rotary Diesel Fuel Pump in 1HZ engine it has those think its 5 veins like that and they just sit in the slots in very tight tolerances and centrifugal force spins them out it doesn't have any springs. The outer edge of each bit has a slight curve and the centre of the inside one has a straight cut grove i assume help to not make suction when they go in out as it spins. Cool lathing work.

[@Daft_Dhwelk]

Smashing the phone was unnecessary

[@RickdBDutch]

What, does he owe you money or something?

[@Tubaraofaminto666]

Top

[@metallantik]

🙏

[@mrohny76]

świetnie to wykonałeś moje gratulacje 👍👍👍

[@metallantik]

you're welcome 🙏❤️

[@walterretlaw4051]

Nice work but I don´t recommend to wear gloves of any kind.

[@justinadcock9351]

Could you provide a print for the pump

[@jameswoodsist]

it looks like you put the shaft seal in backward at the end, the side with the little spring is supposed to face the pressure.

[@metallantik]

👍❤️

[@sumguysr]

What's your top pressure?

[@odin823]

what that phone ever do to you?

[@metallantik]

🙁

[@victormanuelflorez-y3f]

So freaking cool men

[@hardhy2309]

Please bulid hydraulick motor

[@ToBeeOrNotToBeHoney]

You made everything up to the plastic hub/bearing in the end. Just wondering why you did not also make that since you did everything else. I mill would make many of the things you did a bit easier and precise, but good job using the tools you had.

[@metallantik]

Thanks a lot bro 👍🙏

[@gusgam5522]

Genial...

[@sarmatskif6660]

Дуже круто,єдине що незрозуміло- навіщо телефон зламав?

[@100ampscurrent]

Where is the bearings???😊😊😊

[@metallantik]

Does not need 🙂

[@jakovmashika]

такі насоси є готові їх використовують у сільгосп техніці для оприскуваня вони роликові більш довговічні або для пивних охоложувачів з бронзи и графітових пластинок атакже у бензоколонках

[@Болгарин-т5р]

Зачем ставить пружины под лопатки, это лишнее сопротивление. Центробежная сила и так их раздвинет.

[@SergeyG-lv1ym]

👍👋

[@metallantik]

❤️

[@13FPV]

Oilseal is backwards.

[@Bakhamaster001]

Бінза колонканын насосындай екен

[@metallantik]

👌👍❤️

[@pasuggun9438]

밀폐 밸브가 안좋기에 고정 작업엔 어율리지않음

[@AJVAN_]

Why does everyone unnecessarily destroy phones? Even tho it's not working it can help someone fix theirs and keep trash from landfills. In modern times people only buy stuff. Repairing is where the real charm is

[@metallantik]

🤷‍♂️❤️🙏

[@dadoVRC]

Moving fluid is simple, making pressure isn't. Put a manometer on that.

[@TheLolimperator]

These new smartphones getting harder and harder to open.