Milwaukee Tool Metric 48-89-4875 (5-Piece) Impact /Drill & Tap Set

Milwaukee Tool Metric 48-89-4875 (5-Piece) Impact /Drill & Tap Set
www.homedepot.com/p/Milwaukee...
milwaukeetool.com/Products/Ac...
#homedepot
#tools
#handtools
#milwaukeetools

[@mikemorgan5015]

Yeah, you gotta be careful backing out. If it doesn't index the threads on the way out, it'll cut a new one backing out. I go really slow backing out to make sure they index correctly if I need to use the deburr/countersink feature. Since there is rarely a burr that requires countersinking in my application, I just stop on the way in before the tap disengages the newly cut threads but is done cutting and back out. Never had an issue that way.

[@bradstovall023]

thanks for the video man, you gotta new sub for sure. I'm a Milwaukee guy 4 life love em! I appreciate the vids though, looking forward to watching more of them. I just bought the same set so I searched for a vid on them and yours came up. take care brother

[@WrenchAddiction]

Thank you!👍🏻👍🏻👍🏻👍🏻

[@joerhea5785]

Mill walk eeeeee....... cool stuff !!!

[@TimTim-fl8fy]

Crossthreaded that second m8 pass to hell and back

[@adamnormandin8576]

Cross thread is better than loctite.

[@iand5188]

You drill in the slower gear for metal so they don't over heat the tip

[@WrenchAddiction]

Thank you for that👍🏻👍🏻

[@beawesome9192]

I was blowing the whole video trying to get them metal flakes off😩

[@WrenchAddiction]

Lol!

[@tootightconcepts747]

When I use mine like that they snapped in half so I figure I drill a hole first then use the tapped bit

[@nerdinside8242]

Great video. Subscribed. Now I’m going do the responsible thing and watch the SAE video 🥸

[@daddyjay319]

Pilot holes need to be enlarged accordingly to screw size . User error

[@camerontinkham7664]

Slow that drill down she was about 1000 RPMs too fast!

[@Radzio2006]

exactly.

[@Sonicfly190]

Quite impressed.....would drill a larger pilot hole forM8 and M10 ....great video...

[@WrenchAddiction]

Thank you 👍🏻

[@vrva3138]

Would have been nice if Milwaukee made regular spiral taps instead of combination.

[@WrenchAddiction]

I’m not sure why they don’t...great point👍🏻

[@randellziegler1318]

Hold the driver straight

[@randellziegler1318]

Bigger the bit the bigger the pilot

[@melvinlarsen8846]

Do you have to drill pilot hole?

[@WrenchAddiction]

No you do not

[@LawAbidingCitizen117]

Why don't you use cutting oil?

[@WrenchAddiction]

You sure could...good call. The advertising from Milwaukee doesn’t mention that at all but, good point!

[@Raj-cf6fe]

Is that piece Aluminum or Steel?

[@WrenchAddiction]

Steel

[@ekahamid277]

Oil

[@K3_GT]

미숙한 공구사용법 탭가공의 이해도낮음 버벅거리는진행(탭내야되는데 나사옮겨박고 또 나사에 손이감) 탭가공 불량으로 나사산 파손상태에 무리하게 임팩으로 체결해서 나사산 개발살 쩝...

[@stevecallachor]

Hmmm!,,,.."Fail!!! Stavros

Your supposed to stop where the threads stop

[@giftedhands479]

He is a bad he don't know how to us a drill or lining up his hand he mess the last two hole up himself. You don't have to put alot of pressure on the bit let the drill do it's job.

[@WrenchAddiction]

You are right. I had very little experience with this type of tool back then. Thank you for the comment.