Monoprice Monolith 10 Review

[@dougclendening5896]

I could not believe this was a 10in sub when I heard it. I didn't think it was even physically possible for a 10in sub to go so low and deep. If I didnt know any better, I'd think it was a 12in sub. I think that's where this shines. This will be more than enough for most small and medium sized rooms, while having a tighter response than a 12in.

[@HomeTheaterHobbyist]

I agree it plays ridiculously deep :)

[@mibz1117]

For anyone who's on the fence between mono 10 and pb 1000 for movies and gaming , get the mono. I had the pb bought the mono to compare it and ended up returning the pb 1000. You won't regret it, this thing shakes my 3 story house.

[@tommyboy3731]

I'm trying to sell my svs pb1000 rite now only had it for a month and then I seen they restocked the mono so the SVS PB1000 is for sale in ebay for 390 plus 30 for shipping some come get it I won't the MONO🤪👍

[@JaysStraightUpReviews]

One thing to consider when comparing the HSU VTF-2 MK5 to the Monolith THX Select 10 is the Monolith comes with a full 5 year warranty. The HSU warranty on the amp is only 2 years, but for an additional $60 you can extend the amp warranty. So apples to apples the Monolith is $500/shipped and the HSU is $667/shipped. The Monolith also goes on sale occasionally for a pretty nice discount. A few weeks back Monoprice had it on sale for $375, so I added a second one. At $375 was an amazing deal.

[@HomeTheaterHobbyist]

Great point!

[@mjoet731]

thanks for the tip! My Sunfire Super Jr. sub just went out I might wait for this to go on sale!

[@JaysStraightUpReviews]

Good review. The Monolith THX Select 10 is a very impressive 10" sub. It's a bit unfair to compare it to the larger HSU VTF-2 mk5 that has a larger driver and cabinet. While the Monolith 10 certainly isn't a small sub, it's still noticeably smaller than the VTF-2. Monolith 10 is 5585 in³ and the VTF-2.5 is 6765 in³. Prices are $499.99/shipped for the Monolith 10 and $607/shipped for the VTF-2.5. HSU does run the VTF-2.5 on sale a few times a year for a modest $30 off. You can get the Monolith 10 for $400-$425 buying from Monoprice via ebay, which lately has been running discount codes once or twice a month. I picked up the Monolith for $425 a few weeks back. I think if somebody has a room that is a bit larger they would benefit from the added headroom the VTF-2 offers above 40Hz.

[@HomeTheaterHobbyist]

I agree their not a direct comparison for all the reasons you mentioned. How are you liking the monolith? Do you have single or dual?

[@JaysStraightUpReviews]

I really like it, especially for a 10" sub. I have one of the 10" models and a pair the Monolith 12's. I have the 10 running on my 2.1 music set up with a pair of Q Acoustics 2020i bookshelf speakers and the Monolith sub is outstanding with music. The Monolith subs are very impressive and play very clean and accurate.

[@desimc89]

I need a stop-gap quality subwoofer for my apartment. I don't listen as loud as I want to for the neighbors. I can get the M10 for $430 (eBay sale) or the HSU VTF-2.5 for $230 more. How much am I missing out on the M10 vs. VTF 2.5 for movies? 2.5k cubic foot room.

[@HomeTheaterHobbyist]

For the price difference I'd go with the monolithic 10.

[@MeTuLHeD]

"It's a bit unfair to compare it to the larger HSU VTF-2 mk5 that has a larger driver and cabinet." I think he's trying to say that if you can manage to squeeze out the extra $100, you get a sub with higher performance. More headroom = greater impact.

[@jaekamacho1416]

Got mine delivered a week ago. Went dual due to monoprice %20 off sale at $399 flat, no s&h and no taxes! Returned dual svs sb12 nsd's i had bought presidents day sale to get these. I get what u mean by lack of midbass, these dont kick u in the chest like other subs, my dual klipsch's had kick but didnt dig as deep as the thx 10's do, had the klipschs for almost 10yrs now so it was time for an upgrade. these bad boys are mean! Heffffty 70lbs, 500w rms, down to 18hz for $399?! Wont find a better deal! Great review btw! This and ur thx 10 vs speedwoofer 10s video are the reason i bought them! Love em and im still in the break in period.

[@HomeTheaterHobbyist]

😁 thanks for sharing your thoughts thus far. The monolithic 10 is a Beast! @$399 that is an excellent deal!

[@GSP-76]

I just ordered this sub for my desktop with Kanto Tuk Premium speakers...I think I went overboard with the sub but I'm excited!

[@HomeTheaterHobbyist]

😁😁😁

[@AudioNostalgia]

Thank you for the great and in-depth review. Could you possibly expand on your comment about mid-bass please? I'm looking at purchasing a pair of these for a high quality HiFi system, and your comment made me wonder if these are the right choice. I'll be crossing over at around 80Hz using an external crossover with 48dB/oct filters. Was your comment about mid-bass referring to frequencies above or below that point? Also, did your perception of the mid-bass change with port plug in / port plug out? Any help would be much appreciated. All the best, Shem

[@NickDarnelldaftnick]

Nice review! It really shows a lot when you actually listen to your subscribers and if they ask you for a review, you do it! It's crazy. No other KZbinr has taken that time or consideration for me and wanting to know more about something (of course it's also for everyone like me who is also curious). But again very nice review. What do you think about me getting one monoprice 10 thx sub and a rsl speedwoofer. Do you think I'd have great mids and great lows with the subs together? You should try it!

[@HomeTheaterHobbyist]

Thanks! Putting the two together should work. The tonal characteristics are a little different between the two but with a little bit of EQ/volume work in your receiver you should get them to blend pretty seamlessly. Glad to help! I understand what you mean, one reason I started this channel was because I couldn’t find very many reviews of the things I wanted to know. Please keep the questions and support coming! I use your support to buy products. If I can get a steady stream of support my plan is to begin giving away products/ review hardware.

[@NickDarnelldaftnick]

Home Theater Hobbyist that would be awesome. Keep it up I love you're channel!

[@MrNorcal81]

Really enjoy your reviews. When you were doing your testing did you get to listen to samples with the port open and closed? Also, maybe you might know if you've done Audyssey calbration with the port open but want to try the sub with the port closed, do you have to redo Audyssey? Thanks.

[@jonathanmnova]

How does this Monolith 10 compare to the SVS PB12-NSD that is the predesesor of the PB-2000? Those two Monolith 10 and SVS PB12-NSD are in the same $500.

[@HomeTheaterHobbyist]

I haven't tried the PB12-ND but I really like the Monolith. If you like deep bass you won't be disappointed.

[@JaysStraightUpReviews]

I used to own a pair of the PB12-NSD's and the Monolith 10 is actually very comparable. At lower frequencies is where you notice the biggest difference. The PB12 handles the really deep bass better due to it's larger driver.

[@ulflarsson9693]

Sounds really good then. Wow. 😃😎🔈🎵👍

[@JamaicaSocial]

So you've now reviewed I believe 4 subwoofers, SVS, HSU, Monoprice and RSL... Which is the most musical across the board (blends well with your other speakers) and which is the best for movies?

[@HomeTheaterHobbyist]

😁😁 that’s a great question, most musical Rsl Speedwoofer 10s, best for movies is a little harder probably the Hsu VTF-2, you can feel the bass in your chest more even at low volume when compared to say the monolith 10. I will say the monolith 10, pb2000, and the Vtf-2 all play deep bass really well.

[@fubartotale3389]

I'd be curious as to your take on the Monolith Mini Towers + Center.

[@youssefhamidi8152]

Im gonna test this out against my sb3000. For some reason the sealed sub seems like it lacks that depth and punch that I felt years ago when I had a ported cylinder sub from svs.

[@edwardsanchez3708]

How did it turn out? I was on the fence about getting dual sb3000 or dual M10v2

[@youssefhamidi8152]

@@edwardsanchez3708 so I did buy two monoliths m10 v2. Just using one actually did give me that depth to the bass which was greater than 1 sb3000. When I had both m10s the bass of course was more even and had a bit more punch. I ended up also testing out dual pb1000 pros and imo the pb1000 pro beat out the monolith slightly. The pb1000 pro seemed to be quicker with the bass, much lighter to move around and slightly smaller. The weight of the pb1000 was about 45lbs whereas the the monolith was about 75lbs! For the weight alone Id go with the pb1000 pros. If you listen to music at all then definitely go with the sb3000s. Its an excellent compromise in terms of size, output and depth. It wont have has much output as the pb1000s but it comes close. Id say the pb1000s (dual) are 10 for bass output and the sb3000s (dual) would be a solid 8.5-9. Hope that helps.

[@edwardsanchez3708]

@@youssefhamidi8152 thanks for the quick reply. I saw a piano black version of the monolith 10v2 on Amazon and bought it gonna see how it sounds and get a 2nd whek im back in town. I am going to make a small 3.1 bedroom bedroom setup and was considering the pb2000pro. I have 4 definite tech 14 inch subs and they are awesome for movies but seem sluggish for music. I hooked up a cheap 12 inch bic subwoofer and for music it blew the big subs out of the water interms of how fast it kept up and the higher and broader bass notes it could catch with music but when it tried to hit deep movie bass to me it was like scratching nails on a chalkboard lol. So I'm creating multiple small setups in my house lol. But since you mention it I may take a closer look at the pb1000. I should have a older video posted of my works in progresss.

[@sukhsrboss5693]

Hi. Great review. I am on verge of ordering the Monolith 10 inch. Would you recommend this over the SVS PB1000? I've narrowed my search down to these 2 subs. Thanks again

[@HomeTheaterHobbyist]

Great question, I think the pb1000 is better balanced for movies and music while the monolith 10 is better for deep bass and movies. So it depends on experience you’re looking for. Hopefully this helps!

[@sukhsrboss5693]

@@HomeTheaterHobbyist Thank you for the reply! I understand the Monolith 10 can be used as a sealed sub with the port plug? With this in consideration. Would it not be good for music too? And defeat the PB1000 with its extra 200 watts?

[@WesleyB1211]

I know this is a good bit old, but can you say why you choose the VTF-2 MK5 over this? I have a VTF-2 MK5 on the way to my house (returned the Monolith 10 due to some factory issues), and wondering how much (if at all) the HSU will be. Thanks!

[@spdmusicproductions3435]

Thanks HTH! Great review, nice video production and I appreciate your comments, score rating and honesty! Keep up your great work my friend!

[@HomeTheaterHobbyist]

Thank you!

[@intoitreviews]

I have a def tech supercube 1 and supercube 2 in my home theater right now, was thinking about getting rid of the smaller sub for this monolith 10 or 12... or a rythmik... I think I'd rather the 10 at its price point, but my concern is that it doesn't go as low as I'd really want. Ideally, I'd want it to be able to hit 16hz +- 3db. If I'm going to step it up to the 12, I might as well get the rythmik for the price? f12-300 is $750... and servo controlled. I'll check out the HSU that you recommend.

[@dsc9894]

If your receiver has no auto calibration, is there a way to get the monolith to output sound the way that it should?

[@uzcateguipedromiguel]

When the light is Green in the back on my THX 10, and you aren't playing any music or movie (I mean the sub and your speakers are kind of mute), can you feel a little interference in your sub (on the cone)? You have to put your ear near to the speaker to hear it. A friend got a 12" Monolith and he has that interference as well. So we are wondering if all monolith are like those or just ours.

[@HomeTheaterHobbyist]

I didn’t notice anything during testing.

[@IWASTEDMYTIME]

Great review! Does the rsl speedwoofer 10s have more mid bass in your opinion?

[@HomeTheaterHobbyist]

Yes. I’ll be doing a video this week comparing the two, that should be up mid week.

[@JamaicaSocial]

Home Theater Hobbyist would you buy two Speedwoofer or go with two of these for movies?

[@rain5920]

my 15 inch subwoofer has more mid bass then any other subwoofer yeah my subwoofer play 90 percent of the mid sounds since my subwoofers frequency goes up to 1000 hertz

[@MasaM-c2c]

For me is best time coming subwoofer! My home theater system is complete Yamaha series and i did update my Yamaha receiver at Aventage, really powerful beast. I so much love Yamaha receivers, magnificent looking receivers with Dolby Atmos / Dolby Vision but right now i have not Atmos speakers yet but best time i save money for that!

[@HomeTheaterHobbyist]

Nice! Which Subwoofer are you using? I really like the Aventage line too!

[@arvindkanna5534]

I'm having a very hard time time deciding between this and the HSU VTF-2 MK5. In terms of the price seems to be around $70 extra if i go with the HSU. I'm at 70% movies and 30% music and wondering which one to go with. I do like how the monolith looks comparatively and given its a little smaller it might not be as imposing in our living room. However, our living room is around 13' * 16' and we have an attached open kitchen which adds to the space which is another 7' * 13 ' so when facing the TV its a very wide space, so wondering if it needs a bigger sub... What would you suggest?

[@HomeTheaterHobbyist]

I just released a video where I discuss the HSU, you can check that out here: kzbin.info/www/bejne/lZe0pnaqiN6Zq9E. Personally between the two I pick the HSU because it can/should be tuned it to your preference while the Monolith isn't as tunable. The Monolith definitely looks better than the Hsu but I prefer the HSU. Let me know what you decide and how you like it, I'm curious.

[@madcrabber1113]

I want one for an old receiver that doesn't have auto or manual calibration for that matter.

[@jesterscorner879]

Thank you so much for this. I have been looking for someone who has reviewed the RSL Speedwoofer 10s, The Monoprice Monolith 10 inch and the HSU Research VTF2-MK5 subwoofer. The VTF2-MK5 comes out to $116 more with shipping factored in at this point, so at that price difference would you say the HSU is still the better value for the money?

[@HomeTheaterHobbyist]

Yes, I think it is a better value, even with the additional $116

[@jesterscorner879]

@@HomeTheaterHobbyist Thank You. I think I have narrowed it down to either the RSL Speedwoofer 10s or the HSU VTF-2 MK5. I feel that the Monoprice and the SVS PB1000 are just too close in price point to the HSU to make the compromises worth it, but the RSL has enough of a price gap that it might be worth the compromises if money becomes a factor.

[@bikomwanthi3369]

Hi Home theatre hobbyist, which sub would you choose?! Svs pb2000 vs monolith monoprice 12?!

[@HomeTheaterHobbyist]

I'd go Monoprice 12 over the pb2000. That deep bass from the 10" is sort of addictive. If the 12" version is deeper with more output then it's an excellent sub. Let me know which one you choose and how you like it.

[@bulcub]

hi, do I need to have a xlr reciever to use this? or use xlr power amp plugged into a reciever

[@HomeTheaterHobbyist]

No, it has standard RCA style connectors

[@domwenaubain8983]

I have 2 20yr old velodyne 10 in subs. I can get 2 of those monolith 10in subs to replace them or should I get 1 12 in? What would you do?

[@HomeTheaterHobbyist]

Duals balance the room better so go dual. I talk about the benefits of multiple subs here: kzbin.info/www/bejne/mavRfpWDls9onrc

[@AlphaBiker54]

If the port was on the side of the cabinet instead of middle, maybe the cabinet could be a little shorter, like the SVS PB1000.

[@HomeTheaterHobbyist]

Yes!! I was thinking the same thing. One reason the Rsl Speedwoofer 10s is so small is because their port is rectangular vs the monolith 10 is circular and in the center of the box.

[@JaysStraightUpReviews]

The Monolith THX 10 and the RSL Speedwoofer may have the same diameter driver, but that's about where the similarities end. These subs aren't aimed at the same market. The Speedwoofer 10s is in a small cabinet and was measured by S&V to have a -3dB point of 30Hz, which by subwoofer standards is kind of mediocre extension capability. Not that the 10S is a bad sub, it's just designed to be a smaller option and focuses more on the 40-80Hz range. The Monolith THX 10 is designed to dig to 20Hz or better and has an incredibly linear and accurate response at very low distortion levels (in THX mode or extended). To get down to 20Hz or better with useable output you need a larger cabinet, more power and a capable driver. The Monolith driver is beastly and capable of high levels of excursion for a 10" driver.

[@willo300]

I've just noticed this subwoofer on sale and also with a discount code I could pick it up for £295 UK. your comme ts on midbass concern me though. I have a pair of decent floorstanders (B&W 603), would these produce enough midbass that the Monolith is missing? I don't own a sub so this is pretty new to me!

[@HomeTheaterHobbyist]

I haven’t heard the 603s but from the specs I think they would cover mid bass pretty well provided your amp is powerful enough to dive them. If you decide to get the sub, I recommend you play around with the crossover setting to determine what sounds best to you. I’d start with 80Hz and work my way down 🙂. Hope this helps!

[@willo300]

@@HomeTheaterHobbyistMy amp is an old Pioneer VSX LX70 and I'm running the floorstanders in bi-amp mode, so hopefully that may be enough. Thanks for the advice, I appreciate it 👍

[@wayneross9723]

I have 3 of the 15s great product

[@nellight5397]

Great review! Just wonderin, this sub has the same wattage and freq response (almost) with SVS PB2000 with 500 watts rms. Which one is better for you?

[@HomeTheaterHobbyist]

That’s a good question, I prefer the Pb2000, it did a better job with music

[@optimusprime708]

Home Theater Hobbyist how about with movies, was it a little bit better or about the same

[@HomeTheaterHobbyist]

They both play very well at the bottom end but the SVS may have a slight edge in clarity but their really really close. And I should mention it’s been a while since I’ve heard the PB2000 but this is my recollection.

[@nellight5397]

Thanks for your input. Appreciate man!

[@optimusprime708]

Home Theater Hobbyist thanks mate!

[@Tec2Nut]

Have you reviewed the 15 inch Monolith?

[@HomeTheaterHobbyist]

No I haven’t, sorry ☹️

[@rushgush]

it’s cheap so u gotta get 2, 3db extra should help with the midbass

[@HomeTheaterHobbyist]

A dual setup would be quite nice!! 😆😆

[@rushgush]

113 db at 63hz while nothing huge, is something.

[@rushgush]

right now, i have a funk audio 18 inch sealed with 2400 watts and 4800 peak watts, i’m looking to down size, it’s in a 880 cubic foot bedroom lol

[@brent245]

Just ordered one today

[@HomeTheaterHobbyist]

Excellent choice! Reply to this thread and let me know how you like it!

[@brent245]

Home Theater Hobbyist. I also got a pair of Klipsch RP-160M'S and the RP-250c. I hope its a good setup.

[@HomeTheaterHobbyist]

That’s a great setup. You should really enjoy it

[@juliangst]

I wonder how the sealed version compares to REL subs for music listening

[@krane15]

Only your ears can judge. In theory, a sealed enclosure is more accurate to music.

[@Cblan1224]

Debating dual Monolith 10s vs dual pb 1000s. Small room. Thoughts?

[@HomeTheaterHobbyist]

I think the PB1000 is a little better balanced i.e. will play music a little better. So I would choose it, I also think it's a little smaller in size which is important in a smaller room. Hope this helps!

[@Cblan1224]

@@HomeTheaterHobbyist i appreciate your response.. I looked into the HSU sub after seeing a few of your videos. If I have this correctly, you would vote; 1) VTF 2 MK5 2) PB1000 3)Monolith 10 Right? Physical media and streaming mostly. A lot of gaming, and occasionally music. I'm going for deep bass, and remember I'm going for duals. I'm saying that because I'm not sure if duals would resolve the dip in midbass on the monolith. A contact at HSU told me they were getting a small batch in today, and itd be first come, first serve. I'm not quite ready to buy until Monday or Tuesday, and they said their "main batch" wasn't coming until January. Of course, I can always reach out and probably get in on another smaller shipment before then. The HSU subs would be closer to 1200, while the other 2 would be $950. That does make a difference, but I'm asking you based on sub quality alone, have I got your list correct for these 3 subs (in a dual format)?

[@HomeTheaterHobbyist]

Yes in dual format that would be my list. Based on cost being a concern don’t feel bad if you choose the svs or monolith both are great and duals will even out the overall response. Let me know what you choose and how you like it.

[@Cblan1224]

@@HomeTheaterHobbyist dual pb 2000s just went up from worldwidestereo on ebay for $998. Or 499 singles. I'm sold. It says they have "12+" available on each. Waiting on a damn money transfer. Free shipping. Authorized dealer..so 5 year warranty and 60 day returns. I'm not sure if I'll have the money until Wednesday. I think ill get one now for 500. And then I'll just grab the other one when this paypal transfer is complete. If they're sold out and I end up spending 600 on another one, that's OK. I really wanted the pb2000. That metal grill is just so much more appealing than the pb1000. Shipping is around 5 days.

[@HomeTheaterHobbyist]

Nice 👍🏾

[@docwho10th88]

If you had only one choice....which would you get..the Speedwoofer or The Mono 10? And yes.. I will purchase the one you choose. lol

[@HomeTheaterHobbyist]

🤣🤣 that’s a tough question I really like both but I have to go with my first thought the Monolith 10. I hope you enjoy it! 😆

[@HomeTheaterHobbyist]

And selfishly if you use the HTH amazon link I would appreciate it! Thanks 🙏🏾

[@docwho10th88]

@@HomeTheaterHobbyist Done! ;-)

[@monijam1]

Would u buy the Monoprice 10in or the SVS PB 1000?

[@HomeTheaterHobbyist]

For me the PB1000, it’s a little more balanced for movies and music. The Monolith plays deep if that’s what you’re looking for.

[@monijam1]

@@HomeTheaterHobbyist Thanks. I do want a sub to play deep but I want balance in the bass region also. Looking to upgrade from a couple of Polk Audio psw505's and $500 each is my max.

[@HomeTheaterHobbyist]

Personally I’d go for the PB1000.

[@monijam1]

@@HomeTheaterHobbyist Thanks for the advice.

[@jasonsullivan8001]

The price in your amazon link is 999$. I would go with a svs pb-2000 myself. 👍

[@HomeTheaterHobbyist]

Thanks for letting me know, I’ll look into this and see what’s going on.

[@jasonsullivan8001]

Home Theater Hobbyist it’s weird because the 12” is 860$.

[@HomeTheaterHobbyist]

Thanks for catching this, I’ve removed the link until the price is corrected.

[@jasonsullivan8001]

patk2 I never said anything that had to do with your reply. Who cares who sells it.

[@jayjustgames1725]

Is there a night and day difference with this and the svs pb1000 when it comes to home theater???

[@HomeTheaterHobbyist]

I wasn’t able to compare the two directly but I would say the PB1000 will play a little better mid bass than the monolith. But night and day for ht? No not really.

[@jayjustgames1725]

@@HomeTheaterHobbyist cool thanks for the reply. I ordered the PB1000. Should be here end of next week. 😁

[@mibz1117]

@@jayjustgames1725 hey Jay I'm in the same boat as you were, should I get the mono or svs. I have a dedicated home theater 22 ft long 12ft wide. Did you end up liking the svs

[@jayjustgames1725]

@@mibz1117 i did! Got 2 of them now. Still haven't heard the monolith to compare but I am very happy with the svs. They go on sale from time to time for 399 as well.

[@LifeofBliss]

Just came across your channel sir. Glad to find another HT enthusiast! Great video and overview of features of this new sub. Monoprice is coming out with some pretty decent components recently. I just installed the Amber in ceiling speakers in my theater. Sub'd, keep up the good work!

[@HomeTheaterHobbyist]

Thanks for watching, commenting, and subscribing! The Monolithic 10 is a great sub I was pleasantly surprised.

[@MrDevkaprowan]

I can buy one for small space which one is best over all svs pb 1000 or this monolite 10 inch subwoofer help plz thanks

[@HomeTheaterHobbyist]

I wasn't able to compare the Monolith 10 and PB1000 back to back but based on my experience: The monolith will play deeper than the PB1000 but the PB1000 plays mid range bass better so it's a little more balanced. In other words if you enjoy movies and music with decent balanced bass, PB1000. If you just want deep bass, Monolith 10.

[@MrDevkaprowan]

Thanks you are doing good work i enjoy your videos which is full of excitement of new products thanks

[@HomeTheaterHobbyist]

Thank you 🙏🏾

[@benjamindminor1983]

A good set of towers can handle all you midbass I don’t like my subs producing any midbass let it only handle the lower end.

[@djkyy]

What does the EQ extended and thx do? What is the benefits of it switched up on the lever or down thanks

[@HomeTheaterHobbyist]

Extended EQ causes the sub to play a little louder and slightly more distorted. I tried it out and decided I like more output but not the distortion. So in the end I switched the EQ to THX and turned the level up a bit.

[@PlayshotKalo]

HSU or PB-1000 for home theater?

[@HomeTheaterHobbyist]

I lean towards HSU.

[@tracyherbert2978]

Can you review the Cerwin Vega XLS-215 dual 3 way ?

[@HomeTheaterHobbyist]

I’ll looks into it , I don’t know much about Cerwin Vega, but I can’t make any promises.

[@dry509]

What about the sealed version?

[@HomeTheaterHobbyist]

Haven't tried it, sorry. Hopefully I can get one in at some point.

[@donjaun540]

Good looking woofer. It was shaking my TV. 🤣😛

[@HomeTheaterHobbyist]

😁😁

[@bakulg1131]

How the hell you put that tank on top of he table 😀

[@HomeTheaterHobbyist]

I did fear collapse

[@MichelLinschoten]

Lol should try lifting my power amplifier... looks like a normal sized amp .. Weights 97 pounds

[@martylynchian8628]

How this compare to the PL200II ?

[@HomeTheaterHobbyist]

I don't know I haven't tried it, sorry.

[@jesterscorner879]

BIC America makes nice entry level stuff, but RSL, the Monolith, SVS, HSU Research are all significant upgrades to anything BIC makes. The BIC is only 250 watts RMS as opposed to this sub which is 500 watts RMS. BIC Subs also tend to be more muddy sounding and don't hit as low as any of the higher end brands mentioned.

[@teknikalvette]

It's a subwoofer not a mid bass, your speakers are supposed to pick that up.

[@jasonsullivan8001]

How does this compare to the svs pb-2000?

[@HomeTheaterHobbyist]

The Pb2000 will move more air due it's larger size but the Monolith 10 digs deep which is very nice! The Pb2000 is at a different price point so it's a little difficult to truly compare. At $500 the monolith 10 is great bang for the buck

[@jasonsullivan8001]

Home Theater Hobbyist thanks for reply. I wonder how the pb 2000 would do against the Monolith 12” they are similar in size and watts and price. Keep up the good work.

[@tracer073]

Home Theater Hobbyist compare does not mean value on size, what we want to know is how they sound compare to each other how much better does one one sounds and in what way?

[@alandelgado798]

So this or the svs PB-1000?

[@HomeTheaterHobbyist]

Depends on what you like in a sub but I’d pick the Svs. I discussed that choice in this video: SVS PB-1000 Full Review kzbin.info/www/bejne/h4G9q5eliculnZo

[@philsingh8153]

Heh loving your informative videos especially the honest no nonsense reviews, only thing I would ask when testing subwoofers can we have something different then Jurassic Park when testing for movie performance please..?

[@HomeTheaterHobbyist]

Thanks, what’s your movie suggestion for bass?

[@philsingh8153]

TRON: LEGACY - Chapter 8, Lightcycle Battle War of the Worlds (2005) Flight of the Phoenix - The crash scene Just some suggestions above...!

[@HomeTheaterHobbyist]

I don’t own any of these but I added them to my list of future purchases so don’t be surprised if one or more is a sound sample one day

[@HomeTheaterHobbyist]

How did you like the sound samples?

[@philsingh8153]

Well once you do, you won't be using Jurassic Park for a long time, a slighly older film to try is The Phantom Menace - POD race

[@dantonliam]

Its a “Subwoofer” not a midbass unit so your comment makes no sense at all....

[@astrotrance]

It playes up to 200Hz, which is usually considered midbass-ish. I agree though, most subs sounds too bloated and boomy above about 100Hz or so, and sound a lot better at low freqs.

[@HomeTheaterHobbyist]

Different subwoofers handle frequencies below ~250Hz differently. The monolith handles the low frequencies below ~50Hz with aplomb while some don’t do that well. Just because it says “subwoofer” that doesn’t mean it will play the entire frequency range the same.

[@rakitakhan]

Ummmm...it's a SUBwoofer. It's not meant to reproduce mid bass. That is left for your mains to handle. I dig the review though.

[@HomeTheaterHobbyist]

Thanks for watching.

[@Aleapple96]

is this better or the pb1000?

[@HomeTheaterHobbyist]

I’m currently testing the pb1000. I’ll discuss this in that full review, check back Feb. 24th and watch that review

[@Aleapple96]

Home Theater Hobbyist 👍🏻👍🏻

[@Aleapple96]

Home Theater Hobbyist what size are the screws of the grommets under the sub? are they like those of svs? thank you

[@agustinsoto2171]

THE BAD THING IS THAT IT IS ONLY IN ENGLISH BECAUSE YOU DON'T DO IT IN SPANISH SO THAT THOSE WHO HAVE THE SAME PASSION THAT YOU CAN COMPATIBLE OPINIONS AND QUESTIONS I LEAVE THIS QUERY DONE I HOPE IT IS NOT IN VAIN

[@joemizer]

Are the feet threaded?

[@HomeTheaterHobbyist]

No

[@JaysStraightUpReviews]

Yes they are. The feet are attached to a threaded bolt, exactly like the SVS feet.

[@HomeTheaterHobbyist]

Sorry 😐, Mix Master Ice is correct they are threaded. 2 of mine are so tight i can’t get them off but the other two will come off with a little effort. Sorry for giving you incorrect info

[@HomeTheaterHobbyist]

Thanks for following up!

[@vicinvesta8349]

It is Huge!

[@HomeTheaterHobbyist]

😁😁👍🏾 do you have one? How do you like it?

[@heoaj]

Where is this made?

[@HomeTheaterHobbyist]

I did some checks around the internet and couldn't find a definitive answer but my best guess is designed in California manufactured outside of the US. That is just a guess though.

[@rain5920]

@@HomeTheaterHobbyist my 15 inch subwoofers frequency response is 40 hertz to 1000 hertz

[@HomeTheaterHobbyist]

What is the make and model of your sub?

[@rain5920]

@@HomeTheaterHobbyist my sub model is SN2000 make is absolute usa

[@tommyboy3731]

@@rain5920 They're all made in China now unfortunately

[@MichelLinschoten]

You lost all credibility, midbass? It’s a sub the word already betrays what it needs to do SUB LOW.. Midrange is something your fronts and center do

[@HomeTheaterHobbyist]

I think you’re confusing 2 terms. Mid range frequency covers ~150-900hz. Your typical loudspeaker can handle these frequencies. Below 150Hz is the bass regime handled by the sub. Mid bass frequency range is ~50-90hz. While the frequencies below 50Hz are called low bass.