What a wonderful way of teaching. It has changed my learning experience. Keep up the good work and thank you for sharing all this information .
@frankvega934 жыл бұрын
Walter I have a MCH36 having problems to start
@frankvega934 жыл бұрын
Need support I am not familiar with this equipment the transformer burned and some bulbs
@frankbatusic76233 жыл бұрын
Excellent video Walter! I have been looking for hours for how to setup a remote start for a VFD powering a 3 phase motor on a table saw. Yours by far is the simplest, most straight forward with a clear explanation of how to do it using an Ice Cube Relay and the functionality of that relay. This video provides background support for your other video: "Starting a VFD with 2-wire Start". Thank You!
@ignacioflores77813 жыл бұрын
Definitely, the best site for controls.
@RRRRR7-c7r4 жыл бұрын
I did learned something even being a Industrial Electrician years back. Id usually just use the start / stop etc inputs on the drive though. I personally never have wired a relay to drive like that before so it was a great vid.
@arturogonzalez2220 Жыл бұрын
New at this, just moved from Maintenance Mechanic to Instrumentation and Electrical Tech., i struggle to understand how is it that the motor keeps running after the start button was let go. Saw this video and is very simple, Thanks A lot.
@ismaelmelendez78084 жыл бұрын
Awesome explanation you should have a course online your step by step can’t be any better hope you continue making videos great job
@AccessToPower4 жыл бұрын
Thank you Ismael!
@jaypexlegend83513 жыл бұрын
thank you so much..im gonna look like a genius...you saved the day friend!!!
@davcot36755 жыл бұрын
Great straight forward explanation Keep up the good work
@justingoodsell77924 жыл бұрын
Awesome videos! Thanks so much!!
@stanleykania71845 жыл бұрын
Good job 👍 .. Learning in a steel mill.. seems overwhelming.. place is very loud in places and can't communicate while watching trainer.. Hard place to learn.
@obertosiciliano12434 жыл бұрын
Awesome!!!! Thank you so much!!
@buildingstatux77205 жыл бұрын
Great content
@roberthunt93112 ай бұрын
Do the 2 wires going to VFD need to be 24 volts, or can they be 120 volts?
@nukeelda5 жыл бұрын
Amazing Thank you Sir.
@gregoriocampo4 жыл бұрын
Excellent Video.
@monzurhasan35833 жыл бұрын
Excellent
@BillFye3 жыл бұрын
Why doesn't the power from 1 and 3 cause a short against the line? Or maybe electricity doesn't work this way
@AccessToPower3 жыл бұрын
If you look carefully at the schematic about minute mark 2:40 you will see that 1,2, & 3 all originate from the same source. Therefore they are the same potential.
@vfgrfbgrb4 жыл бұрын
Instead of jumping wires it helps me better wireing like that
@stevemc14 жыл бұрын
Great work, what program do you use for your motor control simulations? Thanks
@AccessToPower4 жыл бұрын
Stephen McAdam I use The Constructor software. www.cmhsoftware.com/constructor.html
@stevemc14 жыл бұрын
Thank you, love your work and videos
@vfgrfbgrb4 жыл бұрын
Can you wire to wire 2 wires from start to 2 and 3
@discretehappiness46232 жыл бұрын
What software is your circuit drawing?
@AccessToPower2 жыл бұрын
It is Constructor software
@ActionMax094 жыл бұрын
Awesome! 👏🏽
@beckyschwantes52874 жыл бұрын
Can you control a VFD with a start stop holding circuit and a field device such as a pressure switch?
@AccessToPower4 жыл бұрын
Yes you could
@Roelyize3 жыл бұрын
I watched you video a lot
@kaylaharrington69583 жыл бұрын
What software do you use to make your videos?
@decentraza79165 жыл бұрын
Hello sir will u plzz explaine me how i conect the solenoid valve timer to auto and manual starter
@AccessToPower5 жыл бұрын
If I understand your question correctly, you should be able to connect a timer circuit in the same way that the float circuit is connected in the video link here. kzbin.info/www/bejne/Z3uWZ4adhaZ1fNE
@vfgrfbgrb4 жыл бұрын
Can you just run two wires to start
@fuzzfacelogic7899 ай бұрын
You're using 10amps for VFD and motor control yet say that 10amp relay not to be used with anything requiring a load? 10amp is the common rating for general residential use, lights and power points, here in Australia.
@AccessToPower9 ай бұрын
The 10 amp relay is being used to on the control circuit of the VFD… not the motor circuit. The current on the control for a start signal is measured in milliamps.
@fuzzfacelogic7899 ай бұрын
@@AccessToPower Please excuse my ignorance.
@AccessToPower9 ай бұрын
@@fuzzfacelogic789 no worries. Thank you for watching and commenting on these videos. We created them to be helpful. Hopefully they accomplish that goal.
@vfgrfbgrb4 жыл бұрын
?
@vfgrfbgrb4 жыл бұрын
Instead of jumping wires it helps me better wireing like that