Restoration 21 inch bass subwoofer // Restore extremely high capacity subwoofer

Thanks for watching, subscribe & share!
Restoration 21 inch bass subwoofer // Restore extremely high capacity subwoofer
#mr_electricity #restoration #speakers
► Subscribe to channel: / mrelectricity1111
Please give me your opinion. Where is not good Let me improve.
------------------------------------------
Thank you for watching the video. please support me. Thanks you very much. love everyone.

[@MisterGulsby]

I did this for years. That sub and box are solid. That isn’t what is rattling… it’s everything else in the shop that isn’t secured. Most likely the wall siding or tools on the workbench.

[@lobster8009]

At 22:30 he just dropped the loose board inside and closed the thing up. That might not be what ratteling but that is janky as heck.

[@MisterGulsby]

@@lobster8009 Agreed

[@garydawson5928]

@@lobster8009 🤣🤣🤣

[@elickes]

If you did work like this for years, I hope you didn't charge...

[@YooTooobJeff]

There's an unsecured circuit board he just dropped in there that is the rattling ghost of hack jobs Present...

[@Bigman.Struggles]

All that work and it rattles like the Ghost of Christmas Past.😂

[@PHUSII]

Its the workshop rattling, not the woofer

[@teddysickels1857]

​@PHUSII it's all of the components that were just thrown inside and not secured! Why use braid nails that are just going to vibrate loose and plywood? Why not use MDF, Screws, and glue where they'd be less likely to vibrate?

[@martinparr193]

Because he also used wood glue and plywood is much stronger than MDF and I do believe that the guy used maple veneer plywood which when stained and waxed will make for a beautiful box.

[@corners3755]

@@martinparr193 It's not about the strength. Its worthless if it rattles like this. So what if it looks nice and is strong if it sounds horrible? Its like building a lawnmower that's fast and looks good but doesn't cut grass good at all

[@tvrift]

@@teddysickels1857 Wood glue is not going to vibrate apart. Plywood is lighter than MDF. I wouldn't want to lift a cabinet that size made from MDF.

[@joeb2648]

sounds like beating on my garage door lol

[@djmips]

That's how they made some sound effects back in the day.

[@TheVermette91]

That’s the shop virbrating ☝🏻😅

[@AParallelReality]

Finally.. a resto video that makes me feel good about my own resto’s

[@NoelRosas-w5o]

❤❤❤

[@derHerrMueller2]

Ja weil schlter geh es nicht mehr

[@pounderish]

Through all those components in the back without securing them isn't the vibration just going to bounce them around

[@markchidester6239]

With the knowledge he has to be able to do what he just did, how could he possibly not know that the parts need to be secured? He very likely didn't show that part because he believed the viewers were intelligent enough to figure that out. Yes. Absolutely.

[@JonW77]

@astheworldburns3590 Agreed. Probably 90% of the average population are fucking idiots.

[@dreammix9430]

I noticed that too

[@AtomicRadii]

Electronicals will probably last 6 months. Then broken solder and other pwb problems. Interesting build though.

[@leonelalmeida7921]

With the not fixed components, this technician is assuring that his customer will return a few months after the warranty void... This is a continuous business plan, buddy 😅😂

[@madmanmoz6365]

Its something in the room rattling, that sub is solid 👌🏼

[@SireSquish]

Yep I was thinking that because there's a tiny delay.

[@asdfghjkl1755]

they threw in entire ampifier inside it would be a mirracle not rattling

[@MrGigi-dz9cv]

The board under, or some lose part.

[@BayermitBauch]

der Subwoofer ist Müll

[@xConundrumx]

@@asdfghjkl1755Yeah so it isn't just me that was wondering about that ...

[@ВиталийЧенцов-я5э]

Руки оторвать за такую работу

[@patruot1]

За что

[@vadimkharassakhal2048]

За неправильный подход к акустике. Оно и слышно как пердит а не играет. Неправильно ВСЁ! От пищащей щели перед динамиком до пердячего ящика без рёбер жёсткости и звукоизоляции. Хотя динамик восстановили классно.

[@vladimirpykhtin3600]

Сам в шоке 😲! Пердозвук а не "низы"👎. Свой "саб" когда впервые тестировал все наровил вывернуть так чтобы выделить "буханье" - результат полное искажение звучания трека. Звук должен мягко заполнять пространство (комнаты, зала) тем самым "дорисовывая" панораму звука.🎧🎼

[@diabolicalartificer]

Working with what you had & probably on a small budget, I think you did a pretty good job. If it does the job that you built it for, then that's ok.

[@mrjive314159]

I doubt they are going for quality here. It just has to be loud loud loud for some concert venue. Did you see those transistors? I think they were "used" as well, lol. Gotta commend the Asians, they know how to rip off a quality design and make it cheap cheap cheap!

[@jesseyap5106]

its the roof that's making that rattling sound, Asian roof mostly is made out of thin metal.

[@mmdirtyworkz]

If it was built for a table then we can say it does the job. Sound wise you have to be deaf in order to say it sounds good.

[@HomeGrownKicks]

When I saw them flip flops. I knew it was gonna be quality work 😊 👌

[@farerse]

never judge someone by their shoes

[@mondotv4216]

Actually if you look closely they were Chinese Safety boots. That's what we call em in Australia anyway. 😅

[@onisiforosonisiforou]

Respect for the effort , how many of us who judging this man could do what he did ? For me is excellent try , if we don't try we will never know or learn . Is from mistakes we learn what's right !!

[@robert-h2x]

yes excellent TRY. i did my diy 12 incher. and the fact the wiring keeps getting lose after some playin no matter what i do is frustrating.

[@BECALIBLAGESCU]

Întradevăr omul îl repara dar nu va avea parametrii unui difuzor calibrat pe Osciloscop să-i controleze rezistenta care se măsoară în Omi puterea în ești și dispozitiv de calibrat bobina între magneți pentru inceput se învață dar îi trebuie Aparaturaaaaaa

[@GeorgelBujoreanu-zw1qj]

👍😀👩‍🔧

[@johnrex2750]

@@BECALIBLAGESCU oui

[@mmdirtyworkz]

1h tutorial on youtube and everybody can make a better subwoofer. Sorry, this was not a SW, if's a heavy table. Shoddy work but we all saw the flip flops telltale sign.

[@Silenceville]

No isolation, the circuit boards just random lose inside the box? They shortcut at some point of the movement and rattle. Nice work, but in many ways not good enough...

[@jakoblindekilde5832]

I don't think they left the pcb board loose - do you?

[@AzTurboMini]

​@@jakoblindekilde5832 yes!

[@imperius_lxxvii9999]

@@jakoblindekilde5832I’m sure he did

[@saihunglam3192]

​@jakobl，，❤😂😂😂😂😂😂😂‘’❤❤😂😂😂😂 ，🥲🥲🥲🥲❤🥲❤❤❤～❤

[@soldjahboy]

Attaching the board actually causes MORE vibration because it's then firmly attached to the vibrating surface of the enclosure. Either use rubber anti-vibration mounts or let it free float. Both methods are equally viable.

[@alterdphsycosis]

Dude this restore went completely different than what I was expecting 😂

[@bdgamingzone1386]

😂😂😂

[@emmarichmond423]

?, what did you expect?

[@DanielCardei]

When you see old tools still working, that tells you someone has experience.

[@mmdirtyworkz]

not this dude lol

[@damiensadventure]

That speaker sounds like my tank in War Thunder at 4:20am when i havent slept in days. 👍

[@JasonRayShute]

Looking at the replacement of the bottom coil support wondering why. By the time the amp wiring had started I understood. Way more than the title suggests. 😊

[@RossVanHog]

Excelente Hermano 👌👍 Se Oye Genial Yo Pensé Que Solo La Ibas A Reparar El Puro Subwoofer Pero Le Isiste El Bafle Y Su Alimentación De Carga Y Woooooo Genial Genial 🙏💯💯💯💯🔥🔥🔥🔥🔥

[@whollymindless]

The B roll of the rain was great storytelling.

[@mrjive314159]

Did you see the brick wall? Everything done there is done fast and cheap.

[@Darren_Martin]

Loving that table saw setup. Nice work on the speaker repair. Maybe add some silicone at the joints to seal the cabinet better

[@michaelpacker9805]

You know that’s going on one of those crazy tractors with huge bass!

[@Skully317]

Looks like something you'd buy out of the back of a sketchy looking van in a Walmart parking lot.....👏

[@David-js6sg]

Yes but how many ppl did this? I did as a kid

[@rickvan102]

Would like to know where the replacement speaker cone came from?

[@carlthor91]

Agree 👍👍

[@ckm-mkc]

Just search for "replacement speaker cones" - one that size is around $22.

[@ad_adov]

он там стоял новый. ютубес перед спектаклем его снял, потом обратно поставил

[@CnJForge]

Nails and plywood? Next time, use screws & remove them after the glue sets and use MDF. Also, make sure to secure all interior components.

[@juuh771]

he did secure all the interior he just didn't show it. while i agree mdf is a better airtight box that plywood works well enough to not be a major issue.

[@przemekkrzykos]

plywood is acoustically better than MDF board

[@CnJForge]

Plywood is layers of wood held together with glue. There are imperfections in the wood & in the gluing process that cause distortions in the sound. Those imperfections are not present in MDF.

[@przemekkrzykos]

@@CnJForge We are not talking about the lowest quality plywood with manufacturing defects, but about the real material which is many times more expensive than MDF board.

[@CnJForge]

There will always be imperfections when using real wood...always. It will crack & splinter. MDF or HDF does not do either.

[@RyanBassForLife]

It's nice. You built a very nice subwoofer box for that. If someone reads this I want to say the best 18" Pro Audio PA subwoofers for the price are Rockville Audio and Dayton audio and a few others. I have had an 18" $175 CT Sounds Tropo and did some KZbin vids in my bedroom of it on a Hifonics BRX2000.1D amplifier and it also sounds amazing.

[@gavincurtis]

Dayton drivers are quite nice.

[@gavincurtis]

Dayton drivers are quite nice.

[@gavincurtis]

Dayton drivers are quite nice.

[@gavincurtis]

Dayton drivers are quite nice.

[@gavincurtis]

Dayton drivers are quite nice.

[@phoenixme74]

Honestly, first "dude repairs a thing" video that I liked and wasn't a pit bike painted black and rustoleum. Cool to see this being done. Good work, man. 👍

[@CoolIdeasDIY-qv1nz]

That was a great idea by a friend😉

[@x84pav84x]

22:32 плату не закрепили, сместится и будет короткое замыкание.

[@MateusSantos-mg5gj]

Exatamente 😢

[@KAJI9lH]

22:36 и отверстия надо закрыть свистеть будет

[@sominongrum3620]

7887

[@Виталийсамодельщик]

​@@KAJI9lHВсе для контента, с такой фанерки не делают сабы, дыры тупорылые, динамик из хрени, плату бросили внутрь. Если малый дифузор или нет, то тугой бас будет и толстые стенки. Тут кал дребезжащий 😂

[@matthews8374]

Thanks for recording that! I used to recone pro audio speakers. I always loved bringing a dead blown speaker back to new condition.

[@veintiunico5326]

Great woodwork. Where’s the damping material?? How was the size of the baffle determined??

[@1337treats]

Non existent. Undersized. Still a massive woofer though. When it gets loud enough maybe it drowns out the rattle.

[@2000teamtoyota]

If the worker has on flip flops you know it's gonna be done right 😂

[@bencoss7003]

Homemade table saw you done a fine job with that

[@Tigma-w3y]

Я видел мультфильм где медведь на пне играл, так он там почти такие же звуки извлекал.

[@ruslan8543]

волк там пел зачетно))

[@norway4423]

Тебе вершки

[@wasjaprjanikow412]

На чужой вершок не разевай роток! 😂

[@gemininosaga]

Bears in monocycles 🇷🇺

[@josecallorda7845]

Es una restauración del bwoofer bastante parcial en la que no se sustituyen partes críticas para el funcionamiento como lo son la suspensión de la parte inferior del cono y la bobina.Estos elementos sufren una fatiga eléctrica y mecánica y ya que se sustituyó el cono hubiera sido lo adecuado reemplazarlos.

[@Markuz1775]

Amazing job. I just love it when you can recycle things like that. Many things could be restored and sold cheaper for people that can't afford more expensive things. I noticed lots of waste here at the recycling centers.

[@jonesgang]

I would give them a +5 for the speaker restoration but they get a -5 for the cabinet and circuitry so that give them 0 out of 10. Thanks for playing!

[@brettemurphy]

Another -10 for the final sound

[@GabojLjamaai-wv7vy]

بوةبيللي​@@brettemurphy

[@GabojLjamaai-wv7vy]

​@@brettemurphyال باابا🎉😂❤❤❤😮😅😅

[@kimhansen8615]

I think it's the 3,5M views that plays well...

[@JamesJ30t]

@MrElectricity @0:09 - What is the fluid you used in the beginning????

[@bassmanjura]

Good video, I never seen cone restoration. I like that at certain point he is wearing a winter jacket, yet he still wears flip flops :D

[@prikolist8364]

И никого не волнует почему короб скрипит и трещит весь, наверное потому что такие вещи так не собираються,это ж не колонка для пк с мощностью 30ватт,и для 21 дюймов динамика, очень слабый усилитель, показать людям что такое возможно собрать дома это хорошо,но качество должно ж присутствовать хоть чуточку

[@Виталийсамодельщик]

С такой фанерки сабы не собирают, нужна 20 мм и ещё с распорками. Тут ещё хрип какой то, дешовое блеяние😂😊

[@raulluna249]

good work

[@blue68chevelle]

First time I’ve seen anyone else actually repair a speaker. back in my teens and early 20s. I used to get a lot of 6 x 9“ car speakers, and a few home speakers that didn’t work. Usually the car speakers had cones that were split all along the outer edge which made them rattle. One trick I would use is to simply cut out the damaged part, Take a vinyl tablecloth with the cotton/fuzz backing. Cut a donut out and glue it to the speaker cone/frame with model glue. I had one set that had been sitting in a vehicle in a salvage yard for years and after I repaired them, they were perfectly fine for several more years. The other thing was where the wires for the coil come out in attached to the cone. The black epoxy glue would become brittle and crack, snapping the wire in two. Those were usually fun to try to repair.

[@shenjohn8546]

transistor will operate in high temprature without any ventilation ,at high levels which leads to distortion and destruction also affects transformers secondary winding.....

[@vancemccarthy2554]

A lot of my repairs are like this. It's the easiest way to go about it when only the cone is damaged. Solvent doesn't have to be used and is faster with right tools and technique. But well executed.

[@rayscherry2383]

I watched all that and you could not play some music through it ,waist of my time

[@johnd5398]

if you're so concerned about your time, spend more of it learning to spell and less watching YT videos.

[@sal50111]

😂😂😂❤

[@harleydavo1099]

The speaker is broken...... ASMR.........

[@jjryan1352]

Get a music player app, genius.

[@popanda3652]

Thanks for rhe heads up

[@arunassilkas3207]

You have not fixed any of the boards inside?! That is why it sounds like metal tool box hit by the hammer 😂

[@JSBuehler]

I am impressed by the minimal tear-out in cutting and routing the plywood. Pity about the raw edges and glue smears.

[@arthurpratha9942]

What product do you use to remove the glue?

[@sevbait]

Probably high % rubbing alcohol.

[@danp101]

Acetone or 99% isopropil alcohol.

[@georgeburdine5660]

Good step by step,even though it looks like a few steps were missing.

[@johnd5398]

missing = not shown

[@mashed-out]

Sounds super SICK!😮😂

[@rutikuiwa7133]

Very nice job

[@JPANadventures]

Marty McFly approves 👌

[@The_Vaporizer]

To everyone talking about the sound..... You do realize you're judging the response of a 21-in woofer on a handheld phone 😂 Good luck with that

[@johnrex2750]

Beautiful work. Now the owner can annoy neighbors for about 1/2 mile away!

[@pbenson56fran]

❤😊 hello Mr Electricity. If only I was as talented as you are. I would repair my speakers and receiver. Have a good day.

[@raymondjmcclain]

I believe you left a box of screws inside the enclosure.

[@Максим-з5й4д]

Пойдет. В индийских боевиках удары озвучивать само то!

[@usersegoniavihodnoi]

Ахах)) "Дышшш" 😂

[@vitaliyn4797]

Рокки бальбоа 🤣

[@АндрейАндрей-х1ф5ы]

Не Радж Капур!

[@bxpress6507]

I am glad I bought polypropylene instead on paper ones!😂😂 this reminds me of the old days😊ported boxes or not😊

[@thomasschafer7268]

Der natürlichere Klang ist aber Papier. Gerade im Bass. 👍🇩🇪

[@bxpress6507]

@@thomasschafer7268 I had two 8" subs in my t-top '88 Pulsar NX SE..one day a storm suddenly popped up..by time I got to abandoned car wash for shelter I saw water sitting on the subs! (The Amp was protected)..Had I had paper subs I be crying!

[@wewillsurviveone]

Are you sure that's not a woofer and not a subwoofer? Not being funny but they are notably different. It's all about the response range hence the sub in subwoofer. If it's for home or pa use them it's a woofer aka loudspeaker. Anything older that would be a subwoofer would be for cars only as they made no subs for homes until recently

[@user-yd1vl9lj5j]

Cool to see. I've sent my Vegas out to be serviced once, was curious how it's done.

[@НильсКлаус]

Звук. Это что доски перекидывают с места на место? 😂

[@Виталийсамодельщик]

Китайский саб за 500 руб лучше свучит чем этот каллл😂

[@vicferrmat4492]

This video is a 'must watch'. Thank you.

[@Aprilfools2613]

What is the chemical you used in removing rubber adhesives. Thank you for your reply.

[@m.s.8422]

IPA for sure ( Isopropyl alcohol )

[@JerrellKull]

I wish we could still buy M.E.K. The real stuff, not the m.e.k. substitute crap everyone sells now.​@@ZAPATTUBE

[@samuraichamplugen]

Every subwoofer company out there: buys same basket made in china. Puts same voice coils, suspension, and surround in it. Puts on a different cone and logo. "our sub is the best one out there"

[@lynxstarautomotive208]

Lol that’s every company these days

[@deadred80]

I built a home theayer sub with a car subwoofer and amplifier once . Used a hefty 12 volt power supply and capacitors . Sounded great .

[@preechajudhai]

I like that. Thank you.😊😊

[@lunatic3571]

that clear plastic you put on the back of those transistors are really good at blocking electricity and heat. you should have isolated the back of the board if you were worried about shorts.

[@fewwiggle]

That's likely mica insulators as the back plane of the transistor is at the collector/drain's voltage/potential and must be isolated from the heat sink.

[@andyvega8220]

I couldn’t stop watching!!!!! 🤷🏻‍♂️

[@loudblaxz6759]

i watched the video till the end.neat and precise great job

[@RomanMelihhov]

I adore your skillset and expertise. Well-done!!!

[@majorxdf]

The speaker isn't making that noise, it's something in the garage. Nice job!

[@joevk6274]

Sounds like someone off camera banging on a piece of sheet metal with their fist.

[@cloudyview]

I think it's the entire garage 😄

[@BigPauleyD]

Awesome, Wish I knew how to do this in High School, my Car would have been Bump'n

[@zenobiomenezesalvim1398]

Are the plates loose inside the box?

[@feeterican]

Yeah that sound like a box that was constructed without clamps. What I'm saying, you should not hear the box make noise. That box is making a whole lot of noise.

[@ArmyMedicRN]

It's most likely the sound of everything in the room shaking, not the box

[@joemedina2251]

Hi my name is Joe just have a question where do buy the parts to restore any speaker thanks so much

[@kyzor-sosay6087]

Google,speaker cone replacement.

[@ronaldglider]

@@kyzor-sosay6087 that does NOT give useful results.... Need a link!

[@johnd5398]

@@ronaldglider go find a link and stop expecting to be spoon fed in YT comments.

[@bangromalampung]

Beutiful...

[@Sahil-Singh.]

it's not subwoofer. it's a woofer.

[@HAZNIK_REMIXER]

Yeah you are right

[@JANREY-ci2yg]

No its a PA subwoofer usually PA subwoofers like this one have woofer edge in it

[@XPRIMEMOVIES]

Exactly

[@russgladstone432]

It’s a bass bin woofer… definitely not for sub bass, deep but not low, minimal woofer excursion

[@Arpar100]

forgot it.

[@Antartunggal]

Very nice 21inch replacement leaf subwoofer speaker repair we love it and we just found your channel and support your work my friend

[@Tom-zq7lu]

Fantastic and beautiful thank 😊👍👏👏

[@erickmagsanay4043]

Sub is Solid, that rattling sound is coming from a garage door or something loose, even my 10 inch sub can rattle a loose garage door.

[@dodgeguyz]

Wait a minute!……….where do you buy all that stuff from?

[@warrenpeas]

Plywood is commonly used in designing speaker boxes for several reasons: 1. **Strength and Durability**: Plywood is stronger and more durable than particleboard or MDF (Medium Density Fiberboard), making it better at withstanding the vibrations and stresses associated with loudspeaker operation. 2. **Resonance Control**: Plywood tends to have fewer resonances compared to other materials, which can help reduce unwanted vibrations and coloration of sound. 3. **Ease of Construction**: Plywood is relatively easy to work with, allowing for precise cuts and assembly, which is crucial when building speaker enclosures to specific dimensions. 4. **Weight**: Plywood strikes a balance between weight and strength, making it easier to handle compared to denser materials like solid wood. However, the quality of plywood can vary, so it's essential to choose a high-grade plywood with minimal voids and consistent thickness for the best results. Additionally, proper bracing and damping materials may still be necessary to optimize the performance of the speaker enclosure.

[@UnderTheBridgeLiving]

My bullet tweeters got more bass 😂 lol. Amazing woodworking & solid build tho. 👍🏾

[@myalaynaangel]

Same here

[@johnd5398]

anther idiot expecting to hear bass on their fucking phone...

[@carmelocampisi7152]

What liquid compound do you use to release the glue

[@Middlestepofficial]

Should have opened it completely and check the windings. If the coil is damaged, no membrane replacement can restore the sound of the speaker.

[@sb-cg3zq]

Umm...am I the only one who noticed it didn't work?

[@syedaliahmed2893]

😂😂

[@666kuzya666]

I see the same. They used the membrane of wrong depth or wrong density. So, the magnet is striking the bottom of the coil cup.

[@juliovaldez5468]

Did you guys listen to this on a loud stereo system? I'm sure the metal noises you guys heard were objects nearby getting rattled. I think it's a bad idea for people to try to demonstrate subs on KZbin, though. There's just too many variables on the viewer's side to really hear what they are hearing.

[@steve390gold]

​@@666kuzya666no thats everything in the shop rattling

[@tangois]

​@666kuzya666 What membrane are you talking about?

[@piratedave1005]

yes, but most of us don't have access to that wee bottle of yak piss which must be magic

[@akella728]

Столько усилий для дребезга))))

[@ilgizenikeev4114]

В 86г 10ас-403 перематывал тк сгорел усилок а за ним и катушка, сам удивляюсь как шестикласник(я :)) смог это сделать но потом не мог по звуку отличить колонку от заводской (одна сгорела) . Главное в конце покак клей не до конца застыл отцентрировать катушку чтобы не касалась магнита, смотрится невозможно но навеяло

[@RoyZenzo]

@@ilgizenikeev4114покак

[@GambitCoach]

​@@ilgizenikeev4114 to center the coil use thin plastic of 1 to 1.5 cm wide and approximately 5cm long you can use old xray to cut the plastic and use it to hold like this 2:57

[@billybunter3753]

It's the shed rattling. Brains are for using, try it sometime!

[@dannypalmer7701]

That is a cool saw! 😊

[@TENACIOUSDRAGON]

The video is good but it's much better if you include the names of those chemicals and materials you used while you remove and fix the speaker!

[@Njazmo]

IPA Epoxy Wood glue

[@johnd5398]

It's not a how-to video. See title/description.

[@TENACIOUSDRAGON]

@@johnd5398 lolz before you say something TRY TO UNDERSTAND FIRST WHAT'S YOUR READING!!🤧😮‍💨

[@Suavache]

Anh là chuyên gia làm mới loa anh có dạy nghề không ạ

[@DianaAma3000]

За исключением нескольких манипуляций с электроинструментом, показано всё, чего делать не следует или надо делать по другому.

[@myalaynaangel]

Nice

[@xplmr1]

TEMU factory refurbished.

[@Ajith-ib3ul]

To the extent of saying that it cannot be said that s

[@fraibalhenao]

Hay que probarlo bien en espacios abiertos a ver qué rinde. Así no se aprecia y eso lo sabemos. La estética está bien pero sugiero le coloque una rejilla al frente para que se vea monstruo. Ahora sí le activas un sistema para que también sea pasivo, osea dual allí le podemos meter un 5 mil a ver qué cara pone y si la caja aguanta esa precio para sacar el verdadero sub bajo que se necesita en el sonido. Saludos desde Venezuela.

[@sandiegodan]

Nice work but give more details of what kinds of materials you are using. Solvents, glue, etc.

[@johnd5398]

It's not a how-to video.

[@erickoliveira7039]

*Fantástico ! Parabéns 👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻 🙋🏻‍♂️🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷*

[@faaiquealimehmood]

can hear the plywood box

[@adijatmikom]

Kalau pesan brp harga

[@johnd5398]

Unless you're running sound through a home theater system or custom car audio system, you can't hear half of what that speaker is doing. What you CAN hear is shit in that shop rattling around.

[@SEGERChannell]

Mntp bang dilnjut 😊👍👍

[@Partizan862]

Фанера тонкая для такого динамика. Нужна фанера 20мм минимум.

[@Sergios37100]

так столько по виду и есть

[@vitorreis6618]

Fernando vc poderia fazer um vídeo mostrando caixinhas de sons mais robustas, com esse padrão de bateria

[@НиктоНеизвестный]

Весело смотреть на эту дичь)) особенно проОРАЛ с усилителя АВ класса на ватт 400-500 на вид. засунутого в закрытый бокс без вентиляции))) а еще с трансформатора на 2кВт номинала... хотя тут бы хватило 500Вт трансформатора. усь уних сгорит от перегрева через 10 минут работы этого саба...

[@EffinGuy]

I built simple particle board boxes once... This box is elaborate in its own way