NEW!!! Harbor Freight (BAUER) 6 inch Polisher! W-T-F Were They Thinking?!?!?!

[@apexdetail85]

Stay away from this one my friends.

[@jimboh5131]

Thanks for update Brian; you're the man.

[@andrewyaadigg]

Even for just a dedicated 3 inch polisher for the hard to reach places?

[@bige8397]

Dr. Brian, another thorough dissection. No doubt, a thumbs down on this one. Excellent work :) .

[@ldtriton]

Omg!! This thing was stalling over the most minimalistic of body lines on the panel. 🤯 I still have and use my original Harbor Freight and it goes over body lines without even flinching. This is an epic FAIL! Great review as always!

[@Carlos.Rivera]

Thanks for bit the bullet rather than us

[@SeanN-58]

Here's a thought...get the extended warranty and if it breaks just replace it. Man, what a critic!! Most people are just looking for something to polish their own vehicles a couple times a year and I'm sure this Bauer will work just fine.

[@muchachogrande2019]

Seriously I don't see any huge criticism that couldn't somewhat easily be modded and improved. At the point you're taking it that far apart you can easily swap out the grease and counterweight. If somebody wanted to go even further I'm sure it wouldn't be super super hard to coat the winding wiring in epoxy as well, and replace the bearings with some sealed bearings. Not to mention there's a lot of stuff made for the Porter Cable that's a direct fit for this polisher. I agree with Apex about many things but I feel this is just overly critical and not looking at the bigger picture.

[@Chocolate_dragon]

I think people forget this is a cheap homeowner grade polisher. It’s not meant to be used in a detail shop every day. I bought mine for 49.99 with a coupon. I have 5 cars I do once a year. It’s been a little beast.

[@FasterBastard1]

Right!? What self respecting shop owner buys anything Bauer? Let alone expecting it to last?

[@dannysalinas4511]

But I'm worried about early premature wear and tear from not having a plastic cover on my bearing. Hold on let me cook these screws with my Dewalt. 😂 don't worry though I got it on a non static mat

[@GLF426]

Bought one last weekend and I LOVE this thing. Yeah it's got a little vibration to it. No biggie. For the price it does almost as good of a job as one 10 times the cost. On a car that hadn't been paint corrected in 20 years ( yes 20 years, I know because it's a drag car and it's mine ) after doing a compound, mother's California gold cleaner wax, and then a final polish the car is almost flawless. It's very nearly like brand new. Talk it down all you want but this thing is a beast for the price.

[@perezism1979]

Really what you expect for the price it's a good ass polisher! Your complaining about the switch? Don't understand. To much details looked after for what you probably comparing to. I use it all the time and love it...

[@richymoreno2567]

Still holding up my dude? I am not a detailer or anything so won't use it every weekend but will do maybe every 3 to 6 months at least twice a year.

[@gopaulsalick507]

@@richymoreno2567 I personally have one of these and left it all original, (didnt tear it apart) got it for 50$ been holding up for almost a year already

[@richymoreno2567]

@@gopaulsalick507 nice man do you constantly use it? I just got one too this Friday the 64529 version!!! Can't wait to use it!!

[@gopaulsalick507]

@@richymoreno2567 i use it probably on 5-6 vehicles twice a year so far, the only issue I had was the power switch

[@richymoreno2567]

@@gopaulsalick507 what is the issue?

[@emmakrause1049]

*Good **MyBest.Tools** power and rpm😍 💯 😓 😀 😂 😉 😍control.*

[@lacro5686]

It's good to know the new Bauer polisher is not so good. It's too bad because they had a good tool that could be greatly improved with a few mods. Something many don't know is there was two different 6" Chicago Electric polishers. One was well made, but the other was not. They both were the same price, and one or the other were available at different times. The CE polisher is really a good machine especially with 5 easy mods: (1) Throw away the 6" backing pad and get a 5"and a 3". (2) Get the 5" counter weigh. The 5" Porter Cable CW fits perfectly. This reduces vibration, and is probably better for the tools longevity. (3) replace the gear case grease. I use Mobil 1 synthetic which comes in a tub. (4) Change the location of the switch from the side to the top. (5) Replace the short electric cord with a 15-25' cord. I have used the Porter Cable polisher for years, and find the CE polisher to be much better. It has a lot more power, and is difficult to stall. The PC requires running at 5-6 speed to prevent stalling. I run the CE at 4 speed, and it almost never stalls. MY PC is now my 3" polisher, and the CE is my 5"

[@n3ro209]

How do you know if you got the well made polisher or not? Also want to know how to change the location of the switch? Do you just rotate something?

[@lacro5686]

@@n3ro209 kzbin.info/www/bejne/nIW9n6WKmcurrqc kzbin.info/www/bejne/lWiTop-Ze7yimtk

[@hwytravler1962]

Where can you get the 3” head?

[@gjackson6569]

No real reason as to why he can't recommend it to anyone after he has successfully polished his vehicles with the polisher. For $79 it's not a bad polisher. If the variable speed control is a bit loose, simply use a small piece of duct tape to hold it in place so as to keep the speed from changing easily. Most users aren't going to spend a few hours breaking down the machine to change the grease or other parts. They simply want a cheap polisher that works. This one works and decently at that.

[@minecrafter4623]

I just bought it on sale for $40 so i hope it does the job and holds up for a while

[@dirtriderz6881]

FYI. They have updated the polisher to a new model number with noticeable changes to the body, speed adjustment, balancing weight and shroud. Could be worth revisiting as I believe it is much better quality from version one.

[@ljbrandt500]

new model #?

[@jershaus]

Why? Whats the bottom line that bothers you? Is it the switch? Price? Or the stalling?

[@Samuelfish2k]

J P He seems to throw a little hissy fit at the end of the video but gives absolutely no reason as to why...

[@ad1das41]

Nice review. I bought a few weeks back at a sale price. Worked just fine for polishing my vehicle and I’ve never polished before. If people want to be extremely picky or do it as a job then why not just buy a nice, expensive quality polisher. Did what I wanted yet indoor see myself using it anytime soon.

[@Jeff_Seely]

I think that Brian, like many of us, are comparing this tool to the previous tool Harbor Freight used to sell and was branded as Chicago Electric at nearly the same price. It wasn't perfect but is was significantly better than the Bauer polisher. He simply reviews tools that the consumer is considering for purchase. I actually really like this because of his professional experience and he also tears his down so we can see it without voiding our warranty. I think the review was spot-on and not "extremely picky" at all. But all that matters is that you like yours and I say, keep on polishing! I hope that you continue to enjoy it! When you are ready for another one, I recommend you watch his reviews first. He might help you be even happier that you already are with your current equipment. I am sure that that is his objective with these reviews.

[@Streetmodz-Joe]

I purchased one of these prior to watch this, I noticed that it VIBRATES LIKE MAD

[@AClark-jy2yf]

Can only HOPE/PRAY that Harbor Freight takes note and switches back to the Chicago brand or one of "like"/better quality. Glad I watched this video! Thanks and keep up the great, unbiased reviews! 🙏🇺🇸👍

[@johnhall20]

This is the best tool review I’ve ever seen on KZbin. Good content man.

[@qwicxs]

Works good for me been painting and polishing aircraft for 25 years. Doing spot in repairs etc. Its fine little loud if you have a skill and know what your doing it’s fine...

[@cacocorlino3666]

100% correct

[@BPoweredLove]

3:41 Bauer polisher. Pittsburgh micrometer. This man is all abouts them Harbor Freights!

[@EricK-vy7wt]

I just bought one of these 😂 now I find the video. Oh well it’s better than the one I had so I’ll keep it for now.

[@richymoreno2567]

Which one did you have?

[@ffas23]

Can the Switch be moved from the side to the top? I don’t like the switch on the left side of my Chicago Electric #62862 6” Dual Action Polisher. I thought I read a few years ago about someone moving the switch by turning the head on this unit. So far I haven’t found that video.

[@60trickpa]

Thank you for doing the work so we don't buy a bad product. You are awesome Brian.

[@DLCShark]

So you’re saying if I want an entry level DA polisher this isn’t worth the $59.99(it’s on sale)?

[@JoeBleaux69]

I don’t think he responds

[@robm.6825]

I bought one of these almost a week ago. POS! I took it apart to change the grease and found the gear case halves don't fit together properly (round boss machined off on one area, .030" on high on the other area), the castings were all jagged where the air vents are, the switch intermittently worked. All along with everything else you mentioned in this video. Glad I still have my receipt. It's going back and I'm getting a Griot's. You get what you pay for.

[@martinneps9387]

Now do both of these pad adapters come in the package when you purchase this machine the 3" in a 5" please comment back and do they give you any kind of pads with this machine thank you for this video very interesting I like the machine

[@dannysalinas4511]

But I'm worried about early premature wear and tear from not having a plastic cover on my bearing. Hold on let me cook these screws with my Dewalt. 😂 don't worry though I got it on a non static mat

[@gladstonewilliams4167]

Can you show us how you put the grease in and what type. Also, tell why the grease was replace. Thank you 🙏🏾

[@wormer66]

there is an updated unit 64529 that addresses all the problems mentioned in this video except the epoxy on the PCB ...

[@nolimitslim4701]

IS BETTER OR GOOD?

[@flat4wankel]

The reviews says otherwise. I just need it to do some minor car buffing for details. Still no go?

[@cacocorlino3666]

Its fine

[@nicodemus2192]

Who are the jealous dudes that give Brian's videos a thumbs down? He is one of the best.

[@apexdetail85]

Hey...a thumbs down helps the channel just as much. It is an interaction with the channel. YT's algorithm doesnt care either way.

[@nickb5091]

How would you say this compares to the “Ironton Dual Action Car Polisher - 5.7 Amp, 6in. Pad” from Northern Tool?

[@lizv912]

Can't thank you enough for such a detail forensic analysis. Just earned a new subscriber.

[@ricksgiggle8852]

How would you replace the brushes????? Who makes or sells them?

[@ericness9744]

I'm sure it probably is junk, however what we do not know is if you assembled it correctly. Next time do a test out of the box before a tear down.

[@jamesbiedlar590]

This channel rocks! No BS... only FACTS!!

[@jamesbiedlar590]

If I wanted any shit out of you...I would simply give your head a good squeeze.

[@MyGuyKirby]

Now that you have given them great constructive comments perhaps the next upgrade will improve. Till then, I'll recommend the Griot's Garage G6 unit for a perfect first buy or perhaps the Maxshine.

[@apexdetail85]

I agree.👍

[@tedsperling376]

Do you think the Porter Cable DA will be quieter? Maybe I’ll just pay the 40 bucks extra and get that. Thanks

[@jamesbiedlar590]

This guy does a good service for us. I thank him by hitting that like button, sharing the video, commenting when I can, lets get him to 100k where he belongs...yes?

[@danielalvarez9720]

What other grease other than wolfshead would you suggest using. Would any high temp lithium grease work? I already got this one as a gift so I can't return it or give it back.

[@mkircher88]

turns out there are 2 versions of this machine item 64528 & 64529 (check right below the bar code for item no.). The bad one you (and I) got is 64528. The other model is more consistent to the Chicago electric. Quick way to tell is the dots around the handle insert on the 64528, also the bad machine has the nicer SJ cord while the good machine has the cheaper SJT. Just exchanged mine and am much happier.

[@MrJagot]

looks like they only have 64528 online

[@gerardo2624]

Do you notice the difference? I purchased the 64529 and wondering if it’s better than what he says in the video about the 64528

[@mkircher88]

@@gerardo2624 check out this video: kzbin.info/www/bejne/jYGcoJyQmLmbg7c i would say its the same quality as the old Chicago electric machines.

[@mynsxt6]

They still sell the Chicago Electric version still, Bauer is introduced as their premium brand, I have the CE version and still use regularly

[@loopsandthreads5028]

mynsxt6 in my HF.. CE is no more... only Bauer is available.😢

[@apexdetail85]

Not here in Pa.

[@RanGer-498]

all the ce units are on close out. you can't find them in my area.

[@MrJohami32]

No, not any longer.

[@JT_70]

I just visited my local HF. They now only carry the Bauer. Rats!

[@kevintaylor1202]

Apex Detail... what is your opinion on the Rupes Mark 15 polishers? Are they good at actually making some corrections, or do they bog down just like the Harbor Freight and the Torqx lower line polishers. I have one of the Torqx and I am so over it bogging down if not held in a perfect sweet spot or on a flat surface. I am really looking to buy the Rupes if I can get some honest feedback on it. And btw. Love your channel!!!!

[@apexdetail85]

They are quality...but not for the price. They should be $125 cheaper...each...to start.

[@aarons7267]

I would choose maxshine m85s over this. Same body style but better quality

[@thedgepath1]

Can you get the smaller backing plate at HF?

[@randabuffer6562]

I got one today and have had great finishing using m205 with cg cutting and finishing pads. Is it a Rupes big foot?, nope! But it definitely gets the job done for a weekend warrior like myself 😎

[@richymoreno2567]

Been contemplating one too!! Should I go for it? Just going to use it on my cars 😁 and probably my dad's lol

[@randabuffer6562]

Richy Moreno yes!!!!

[@brotharuss]

What are your fav DA polishers for 3 and 5-6 in?

[@apexdetail85]

Flex and for the money...MaxShine.

[@Ark205]

@@apexdetail85 I have the Maxshine 15, I regret the purchase. Rotation of pad stops with very little pressure no matter how careful I am with the pad level. Even had a professional confirm it was the machine not my technique. Save your money and get a Flex or Rupes.

[@denisef1153]

I have a Bauer. It’s doing it’s job I learned by trial and error to use quality pads. Made all the difference. Of course not with the vibration.

[@mattbenedum8212]

Great review Brian!

[@jdmDC2ftw]

So what do you recommend for a diy-er that's prob going to polish 2-3 times a year

[@neoholland]

It is good at least for sanding???

[@jsk8drummer]

This video just seems overly whiny and n nit picky. Yeah it vibrates a bit. Doesn’t bother me in the slightest. I haven’t had an issue with bumping the speed dial nor does the switch bother me even though I’ll acknowledge it’s not the best. Overall it’s a decent little polisher that is plenty adequate to get the job done for any non-professional. For the price what more do you want. If you’re doing this for a living this polisher shouldnt even be in the discussion and you should know to invest in higher end tools.

[@yousufkhan02]

can you change the backing plate to a 5inch??? if so what brand???

[@barkingspider2007]

Looks just like the Porter-Cable in my garage. I wish they would get rid of the wrench needed to change out the pads. I have let friends and family "borrow" the PC. They always lose the wrench. It costs $6-8 to replace. I have 2 hanging on my wall just for the occasion. Thank you for the video. : )

[@hwytravler1962]

Where to get 3” backing plate

[@efthimios]

I have one it’s ok but I’m ready for something better - the on and off button is hard to move sometimes and it stops rotating of the label has any curves or high spots

[@5hift6ear]

Thanks for the heads up! Sorry if I missed it, but did you ever do a review of the Maxshine 8mm? It is $89 and I have been looking to add it to my arsenal.

[@gravitygear]

I'm waiting for the M8 review as well.

[@apexdetail85]

That one is on the list. I am working on it.👍

[@cacocorlino3666]

Hey Brian I dont know if you're aware but this machine glitches sometimes. First few times it happened I got scared that it was broken. You turn the switch on and nothing happens. You have to click it on and off a few times for it to turn on. This happens once every paint correction. I switch it on, it doesn't doesn't turn on, I look to see if it became unplugged, I see its plugged in and my heart drops thinking my machine broke during a customers paint correction 😂.

[@markpedroza516]

Balsy move to use this to correct customers car. Gnarly dude! lol

[@zachhale9881]

Will I have any problem using a 6 1/2 head on this 6 in polisher? It threads on fine.

[@streetboyz1096]

Does anyone know where I can get the Chicago one they used to sell? Under 100

[@carltonhocutt9918]

I have this unit, got it on sale for$60 bucks. I changed the grease like you mentioned but I used LUCAS RED "N" TACKY grease, it has a 540°F drop point. Is this grease too heavy (thick) for the polisher to operate smoothly. I know you mentioned WOLF'S HEAD but I had the LUCAS hanging around....

[@tunacatcher2003]

Hi! Whats that grease that you replace ? Can i apply that on my Flex 3401? thanks..

[@MrRudyc]

Brian, can you please explain how to distinguish between a hard clear coat and a soft one. Thank you very much.

[@apexdetail85]

Test in inconspicuous spot. If it corrects easily with fine abrasive and non aggressive pad.....soft clear.

[@MrRudyc]

@@apexdetail85 now why couldnt i think of that. Thank you much

[@keithknechg3217]

I was in the market for a da,saw HF ditched the older model...zero info on it.bailed and bought a maxshine....love it 8mm throw 900watts doesnt bog down but doesnt run away on me .

[@followthelaw8722]

he forgot to criticize the warning sticker on crooked too 🤦

[@alanwallace3253]

Thanks fir the video. I have an aged coating to cone off and be replaced with minor correction. I know it’s off topic but what were you using on that truck ? Do you still recommend IGL as well ?

[@donegotold8776]

I'm pretty sure the name change is strictly for profit !? The Chicago electric was a great selling polisher and you can use 20 and 25% coupons on CE brand but can't use on Bauer !!

[@MrJohami32]

I texted customer support and got a $30 off coupon code for the Bauer.

[@sdpikapp]

@@MrJohami32 how?

[@MrJohami32]

@@sdpikappcontact customer service on the Harbor Freight web site

[@eddiemoney9371]

Can you recommend an alternative? I should have bought the Chicago while they still had it. Is it available anywhere?

[@fredcalderon5813]

How much Red Head grease did you use to repack it?

[@Bobster986]

With all due respect, but where can you find a better DA for under $60 (with coupon)?

[@dopedetailing1226]

Bobster986 I said the same thing......I use this for headlight restoration works great !!!!!!

[@marioskosmidhs9454]

@@dopedetailing1226 agree sir. In europe i bought the same machine under a label , it cost me 45 euros......with 3years warranty. I put 5inch /3inch plates..............i do waxings, AIOs, 1 steps on small cars, headlights, bumpers, A,B pillars, very very easy with it. (most european cars in my country are small with many curves) Yes it vibrates a lot, yes it is loud...............also yes..........i had great great great results for the price and the investemet returned back multiple times. Yes my hand are hurt but............i wear hight quality bike gloves....and ........its ok...for 45euros.how i can go wrong?????????

[@marioskosmidhs9454]

notice that.my other option in my country is the das6pro(nice machine) but i sould spend 3-4+times the money i spend for this.

[@jf0314]

Great series on polishers! I really appreciate your work. Now that the Chicago Electric is replaced with this Bauer, what do you recommend for us garage enthusiasts? I used to work at a detailing shop as kid many moons ago, looking to get back into it now that I've picked up an old miata to play with.

[@alduin69]

Harbour Freight whyyyyy 😭 you threw away a decent polisher in exchange for cheap poopoo

[@Smileyguy-jy6xm]

Thanks so much for this Brian. Went to buy the CE and this was all they had. I'm a new enthusiast and only do my car. Used 1x so far. Hated the switch right off. I noticed the vibration but nothing to compare to since it was my 1st rodeo. I have some Gorilla epoxy. Can I just apply that? What DA would you recommend for a personal use ( probably 1 or 2x a year) guy like me?

[@carlosguerra6252]

I need to return mine it gets so hot and after just working one panel it made my hands tingly from the vibrations.

[@cacocorlino3666]

Mine doesn't vibrate at all

[@jmj_d5207]

Wow i just bought this since the long polisher is out of stock and lady said they havnt received any for months :,(

[@socksonfeet8125]

Would be helpful if you stated which Chicago electric model you are referring to, because I still see this model "Chicago Electric 7 In. 10 Amp Digital Variable Speed Polisher" is still available. Its $50. The Bauer is $80, I would much rather get the Chicago electric if it will last longer than the Bauer and at $30 cheaper.

[@tejinder_singh1987]

I just purchased it from canada. Tried in india for the first time for half an hour. Then packed it until new polishing job cane. Today reopened and it's not working. Won't turn on. Please help me. P.S. i use universal voltage converter 220V/240V AC to 110V/120V AC 50/60Hz

[@PinkWillowRanch2024]

I just want to say thank you for your videos. I am just getting over the fear of trying to polish. I have two jeeps and have always hand washed and waxed but never got that glowing shine. So using your videos to try and find the right buffer/polisher machine to get. Thank you!!

[@10OZDuster]

If it were cordless at that price would you buy it ?

[@blakechesbro3602]

just confused as i did not hear a bunch of negatives or red flags until your final assesment

[@tjcheng2574]

Where can you get the carbon brushes

[@frankpuleo2009]

The new grease did the trick like a different machine…omg😳

[@uhh1tsfuzzy]

is the 69924 the better version of this?

[@R0cketRed]

Mine wobbles a lot and of course I really went to use it over a month after buying it so I can't return. Does yours or anyone else experience the backing plate wobbling? I thought buying a new one would fix the issue but others have said it doesn't so now I'm very concerned. I tried hand bending the backing plate as straight as possible but it's not perfect by any means. Does anyone have a solution for me?

[@richardfox3924]

Yeah, add washer/ drill few holes counterbalance and change grease bether quietly also high recommand change backing plate to 5in lake country or forgot other name also have playlist this product mods people did.

[@marioskosmidhs9454]

Change the plate to a 5inch Lake Country + change the grease also if you can = a hole.new machine experience

[@robertswift6101]

I almost bought this one today,,was looking at and for the price I almost jumped on it

[@redhandedreviews3482]

the new one is awesome if....only if you replace the backing pad and grease...I went with the max shine 5 inch backing plate...runs smooth with new grease and backing plate

[@ljbrandt500]

what's the new one?

[@redhandedreviews3482]

@@ljbrandt500 lol its probably a 2 or 3 year mole ...ut it is the one you get today

[@bobp7542]

Can't recommend it you say ? Works for me quite nicely the two times a year I use it...For a full time pro...maybe not...

[@ld4974]

The are 19 reviews of this polisher on the HF website. All 5 star. I just bought it for $59 (with coupon). Will update once I play with it for a while.

[@richardfox3924]

Update?

[@richymoreno2567]

Update?

[@ld4974]

@@richymoreno2567 Forgot all about this post. In the end , I returned it and got a Porter Cable 7424xp. The Porter Cable is just better built and runs smoother, but it does cost $120.

[@richymoreno2567]

@@ld4974 appreciate the reply!!! The guy at harbor freight told me to return it if I don't like it which is cool lol I might give it a try on one car and see.

[@ld4974]

@@richymoreno2567 It does the job but did put a lot of stress on my hands after prolonged use. You may find it's not enough to throw another $60 at the problem. Good luck.

[@chrispompano]

9:44 "Shrimp Wrap"???!!!!..........sound's good to me right now!!!!!! LOL, Brian! Some of us do listen and hang-onto every word you say as scripture!!!!!!! Thanks for another great review. Been curious about this new buffer in the H.F. flyer and glad I bought the older 2nd version of the CE back in 2017, but never used it. I guess the saying goes: THEY DON'T MAKE'EM LIKE THEY USED TO.....

[@Sungodv]

...the shroud screws on the old grey model are soft and the heads strip easily I found out today on two out of three...other than that, I think it is built much better than these newer ones. Somebody say screw extractor?

[@Jeppedy]

Okay, so I watched the video... I saw you pointed out a couple of things, but nothing that screamed "DO NOT BUY!". What did I miss? What makes it worse than the CE version of this polisher?

[@apexdetail85]

If you like your hands going numb from vibration and ears ringing from the high pitch motor ....it is all yours. enjoy

[@MrJohami32]

Jeffrey I have put about 30 hours on the Bauer in about three weeks and he isn't wrong, it is loud. And I hate that damn switch!

[@tornado_dude2039]

i’ve used it for a couple days doing some cars and mine, for some odd reason, doesn’t vibrate a ton. it’s loud on the highest speed but nothing too bad. I do have hearing damage from marching band years ago so that might have something to do with it 😂

[@gregmannos]

Sounds like they wanted to make more profit by cutting quality in a lot of areas. Thanks Brian

[@davebeck3563]

I'll be buying one for sure.

[@Ike-yq3gf]

Thanks for the warning.. Hey had any one every heard sm arnold velocity 15 and 21mm throw polishers? If so what are your thoughts? Salesman stopped by the shop offering them. Never heard of it.

[@noahkraft6453]

Who makes comparable backing plates for this unit

[@marioskosmidhs9454]

Anyone, Lake country, Meguiars ,Griots

[@JJPetro]

You reviewed the HF 64528. You should take a look at the HF 64529. It appears to be a better build and quality.

[@johnlepkowski3831]

Other than an extra bearing and grease. There is slightly better machining. It's not a big update from cheep harbor freight unit. They bolted on a rat tail and front piece for grip to a angle grinder.

[@akaredcrossbow]

What was the cost for the Chicago electric? Did they cost the same? Thank You!

[@ferrante250]

akaredcrossbow I think I paid $69 for the Chicago one.

[@akaredcrossbow]

USMC F2fiddy Thank You! 👍🏻👍🏻

[@dustinpomeroy8817]

They were a little cheaper,but you could use 25 percent off on the CE,you can't on the Bauer line

[@daves.3278]

I got the Chicago electric Rotary polisher. It overheats like a mofo and it's 7 inch backing plate sucks haha I really gotta change the backing plate... Any recommendations?

[@alduin69]

The K-99 backing plate by 3D, great backing plate.

[@daves.3278]

@@alduin69 thanks Niko! What rotary do you use??

[@alduin69]

@@daves.3278 I use an olde DeWalt DWP849, absolute unit and workhorse, and is quite affordable.

[@daves.3278]

@@alduin69 sweet!

[@ModernDIYProjects]

I agree with your review. I have the older Chicago Electric and I did a review on that one before this Bauer version came out. I think the new one has all the problems of the old one (quirky side switch, noise, vibration) but to a greater degree. HF made a cheaper model with this new version, BUT gave it a supposedly new high end name so people would think it is an improvement. HF is slowly eliminating all the Chicago Electric and rebranding them Bauer so people think they are better tools than before. HF is getting very sneaky, Buyer Beware!

[@josetovar7289]

Has anyone ever told you that you look like the bald version of Michael from the Office? lmao

[@SouLAssassin_]

Jose Tovar lmao

[@dewandmcqueen523]

Honest and to the point. Thxs for saving me some cash.. APEX Rocks

[@Krugzug]

The circuit board can have conformal coating put on easily, just need to buy some conformal spray and cover it yourself. Nail polish can work too but keep away from surfaces like the switches and anything that needs to radiate heat.

[@RanGer-498]

IAt first I was like "no way I just purchased this and it's not that bad" after working on 3 cars with this unit I will say its BAD to me and I dont mean bad meaning good . good...my unit would turn on at times and not at all on other times I honestly did try to like this unit but with the on off switch working when it felt like the speed dial that just has no feeling and the noise I had to return this unit...seems like they took one step forward and 2 steps back with this one...this review is spot on.

[@Dee--Jay]

i dont understand... for the price.... its a good ass polisher. Does it get the job done? im sure it does. Is it a headache to use, no! Does it have a few flaws? yes but its cool

[@Jimmygonzalez999]

Can you review the new Bauer long throw polisher