One of the Secrets to the Performance of Playing Low @ 140+db with Small Drivers!

[@pedroveliz4131]

The quality of the components in an amplifier are essential. I remember I got a demo at mad marks stereo in Bradenton Florida 20 years ago,the employee had 4 10 inch Jl w3 powered by a mmatts 1000 watts,it was phenomenal,it felt like a tornado in there literally! Back then that amplifier was $1000! God bless y’all!

[@snhongo1]

💯💯...I always wondered how a high end smaller amplifier will play clean and more powerful than a cheap but bigger amplifier....thats the secret....

[@SilkySmooth02]

He's 100% right on the amp, I used to swear by the old school MTX, Punch Power and Memphis D Class amps. With good power they used to push most subs to the MAX!

[@lifestyleofDAYUNGHOGG]

It probably was audiopipe for me

[@erickthomason9292]

Memphis 1000d is the truth for 25yrs

[@MadballBaby]

I really enjoy that I always learn something new on this channel! 💪🏾Thank you for sharing and keeping us informed.Md❤

[@milesbachelor8747]

This is why the Creator gave us two eyes and ears, to listen and watch. Stay tuned, more knowledge to come.

[@justlooking6898]

I see what yer sayin', lol---I always say 'Believe nothing you hear and only half of what you see' - - - concerning my previous workplace, lol---Take care---🙂🤗😏

[@rainbowsnowflake5754]

Always dropping the FACTS

[@ratherbe7]

Yes sir, I remember how the original Orion HCCA amps had total motor control over the subwoofers.

[@johnregister6437]

I liked the old hcca amps, but to get good power from them they had to be at a very low ohm load, which reduced the dampening factor, so they lost control of the woofers

[@michigansoundwizard]

This is it. Achievement of a Loud CarAudio system with efficiency REQUIRES an efficient electrical support infrastructure.

[@bossman6449]

Yes sir he’s not lying, I heard his truck from across the parking lot at Home Depot the other day 🦍🦍🦍

[@buckyflex1]

back in the day i didnt give 2 chits about electrical i wasnt about to spend $ on dumb shit like ofc wire, batteries, alternator etc that could be goin towards bigger subs $ amp. fast forward 20years and doin a build with proper electrical and and seeing my 8k amp run full tilt pushing 2 15s and my voltage in the steady 14s and zero dimming and seeing the dramatic increase in output im a firm believer

[@Adee4750]

What would you recommend for a 86 Chevy truck

[@rogerdavis2056]

It's the little things like that add up to the big numbers!

[@PaulBourque-l8t]

He's not wrong for sure. Back in the day, I rocked a pair of cheap Crunch 10s that everyone swore were 15s when they heard it. I over apmed everything.

[@didrickdickerson6569]

Good evening MB. I am requesting if all possible, can you do a review on the " Mojo 8's ". Thank you.

[@robj1862]

I'm sporting a 750 dampening factor now all I need is that MBE touch💪

[@josephd514]

So I have a 2016 chevy high country. 2 speakers in the back door 2 in the front. 2 on the dash (Bose) I’m going to run a 6ch amp. But the amp I chose to run, I’ve seen dyno tested. And pushed past its max. Ct sounds atv2-150.6d. 1500w 6ch. I’d go the same route for a sub amp. If it has been tested on a dyno and passed then that’s the amount I get. Idc if the amp cost $200 or $1000 if it doesn’t pass the test, then it isn’t purchased.

[@dcaudio1]

good video MB....i been preaching that for ever......

[@countryfriedfishing]

I got a box test for you. Try making a basic slot port box out of Advantech plywood flooring. Keep the slick side inside the box. I made a dual 6” box out of it once and it was loud as hll. The plywood is compressed and the slick side is just that,super slick.

[@rainbowsnowflake5754]

Use granite

[@countryfriedfishing]

@@rainbowsnowflake5754 I actually tried lining a box with marble once. We renovated a house and they used marble counter tops. I failed epically.

[@rainbowsnowflake5754]

@@countryfriedfishing I build car and home audio enclosures out of granite it not easy but it's rock solid lol

[@MattGuynn]

@@countryfriedfishing under this administration using advantech ?? 🤔🤔🤣🤣

[@countryfriedfishing]

@@MattGuynn Hell yeah. That other stuff just aint no good. But dont worry,,,im seeing lots of finger jointed studs recently. 😭🤣

[@EE0E7]

Does DD Audio have high damping for their amps? How would I be able to find that spec for amps to compare?

[@wehere9686]

In my trailblazer I have my amp grounded to the seatbelt bolt with a lock washer. I use lock washers for everything

[@greenbassboosts8872]

Done two builds on old early 2000s GM fwd platform. I had way bigger issues with the car not being able to produce enough power moreso than anything with the length of the power/ground wire. Emphasis on good electrical connections is good anyhow. For audio at higher wattages i run wire from alt to battery positive. Also ran an additional ground to batt negative to the alternator case. Additional ground batt negative to chassis as well. Upgrading the power positive wire to super gigantic huge wire is pretty useless without adding a bigger wire for the ground ... Otherwise you are just using the original grounds and limited by them.

[@angelverdusco1841]

Hey mb do you have any issues with your dd 4.200 overheating?

[@smurfeco2.358]

I'm running my m8000 at 2ohm it's asking for 3 grounds and powers . Going to power 2 9510L . Hopefully it sounds good compared to my surge audio

[@SuperSportAudioProduction]

I feel like playing low is a different range for everyone💯 you got people that think 30hz is low, you got people that think 25hz is low and you got people saying 18hz is low. What do you consider lows?

[@MattGuynn]

33 and under

[@bryce_fa5si]

Below 30hz is lows

[@subdynoman]

20 to 30 for me...I need that range. I like to have lower but it starts to hog power. In my rx8, I feel 135db from 20 to 60 feels well balance with the stock system upgraded to some infinity 6x9 and 6x8s.

[@bryce_fa5si]

@@subdynoman I just recently had the pleasure of sitting in a blow through Ford ranger by far the best Soundsystem I’ve ever had the pleasure to sit in said it did a 55 and let me tell you 55 is loud enough and low enough for me😂😂😂💀💀💀 I’m in the process of finishing my wall for my 415s

[@goyslop4289]

The system that truly got me into bass was 4 xfl 10s tuned at 28hz, dude would play chopped and screwed songs and the teen notes would suck the air out of your lungs.

[@RaYhEnRiX]

I still prefer multimeter. 😂 Personal preference. Knowledge acquired from MBE N km sticking with it

[@sonnyliston1573]

A 16 volt 500 farad supercapacitor bank would definitely help..

[@greenbassboosts8872]

Look into capacitors enough and you'll find they're just as expensive as lithium unless you go with unreliable cheap caps. Nobody seems to have a reliable answer for how a lay-person can build a balance board either kinda sucks but yea

[@tezd2200]

💯

[@dcaudio1]

MB speaking truth...i had a Audio control LC1500.1 with a damping of 600 and 2 ohm stable putting out around 1500-1700 watts but i wanted 1-ohm capability so i picked up a B2 Audio Rage 2500.1 v2....and immediately noticed a drop in quality of sound. The B2 is a great amp but it doesnt process the same as the AC amp....even though it has twice the power the sound is punchier and more geared toward hard hitting bass versus sound quality bass....truth be told im probably not getting much over 1000 watts on either amp.....which is plenty for me.....current set up is the B2 amp in 4 1506 subs ported tuned to 35......it slams. But i kind of prefer a more subtle smoother sound of the B2 Audio Rampage 8 (2) on the Rage amp....or even better the JL audio 8W7 on the audio control amp.....different animals all together for sure...its fun to have both.

[@blackhornet25]

Is that a radiator style box in your truck that looks like it has a sub on the side of it.

[@M.B.Enclosures]

@@blackhornet25 is a Draco..4 subwoofers no passive radiator

[@meerkhan4404]

Yep the shorter the wire the better then resistance better out come quicker response

[@squadboitv6284]

I never seen this video, how did it get by me!!!!???

[@Thats_X_]

db is bass you can hear? And the Htz is bass you can feel?

[@imnotshort4891]

Db (Decibels) is used to measure how loud sound is and Hz (Hertz) is used to measure the frequency of sound. Bass is usually 20-90 hz, and the bass you feel more than hear I believe is 30 hz and under.

[@Thats_X_]

@@imnotshort4891 appreciate it

[@speedybsracing3227]

Looks like the taramps I have had to go

[@ceciljones1248]

I have taramps and jp63 amplifier and overall jp63 amplifier has more control on my 99Dd 21 it's a lot cleaner sound than taramps I'm going to look for a amplifier that has a high damping on it for better control on my subwoofer

[@nicholasm2254]

Does 2 runs of 1/0 have a lower resistance of that seat bracket? Does 2 runs of 1/0 have a lower resistance that your frame? Without those answers the length of those grounds is meaningless. Also the connection to the seat bracket and the connection from the bracket to the frame also have resistance. Please stop making videos on electrical theory. You are way out of your depth.

[@TheBoofGod]

😂😂😂😂

[@SouthernFarmingTV]

Don't forget about ground bonding. Ground does not run like you think it does through a vehicle.. oh and should never ground using cable. Always use braid flat grounding straps with soldered conecctions

[@michaelvillarreal6574]

Not to mention a random bolt won’t go to the frame unless it’s a body mount bolt and even at that it’s insulated. Better off to drill hole to go straight to the frame or straight to the battery. I would like to see the bottom of that bolt to see if it’s just a seat bolt

[@nicholasm2254]

@michaelvillarreal6574 straight to the battery is a must for me. Way less corrosion and a much better connection.

[@michaelvillarreal6574]

⁠@@nicholasm2254if I can’t reach the battery I double the grounds to the frame for the battery and the same for the amps so it uses the frame as a distribution

[@ahood60]

🤣🤣🤣🤣 pure 🧢