Pittsburg Harbor Freight Engine Support Bar 1000lb. Capacity - Review& Install

Harbor freight Pittsburg brand engine support bar is a good value for the money.
🎦 Ingersoll Rand 2235TiMax 1/2 Impact Gun - Review& Real Live Test
• Ingersoll Rand 2235TiM...
💰Save money on other vehicle maintenance and repairs :
Cheap Way To Check For Bent Valves Without Removing Cylinder Head
• Cheap Way To Check For...
How to properly gap spark plugs
• Car Misfiring? Running...
Proper way to install valve stem seals
• Proper Way to Install ...
Hot Tip: Broken Stud Removal
• Hot Tip: Use a Torch f...
Remove a Broken Stud Below the Surface
• Remove a Broken Stud B...
Oil Bearing Clearance measuring - simple to understand video
• Oil Bearing Clearance ...
How to properly gap and install piston rings
• Piston Rings Replaceme...
How to check cylinder head or block deck for warpage
• Cylinder Head Warpage ...
Why is it important to replace the timing belt at the manufacture’s intervals
• Check and Change Your ...
Fast & Easy way to lap “grind” intake and exhaust valves
• Seating Intake & Exhau...
Replace Front Exhaust Flex Pipe on most 4 or 6 cylinder cars - Cheap Way
• Replace Front Exhaust ...
Better Throttle Response in Minutes
• Better Throttle Respon...
⁉️QUESTIONS
If you have any questions or I missed something, comment below and I’ll answer and try to help you out
If you find this video helpful, like it and subscribe to my new channel. I’ll have tons of videos on all kinds of car and truck repairs in the
future.
⚠️Disclaimer:
The videos on Motorcarnut channel are posted with informational purpose only.
Information posted in this video does not guarantee any particular result. Use this information provided in the video with caution and at your own risk. It is the responsibility of the viewer to take this risk.
Motorcarnut is not responsible or liable for property damage, any loss damage, or injury related to or resulted from information posted in this video.

[@toroloko7257]

Just what I need. I have chains laying around so no problem

[@motorcarnut]

Thank you!

[@GarageVegaUS]

Thanks for showing how to use this, i already pulled my v6 engine a little up without the manifolds. I replaced a oil pan in a Chevy Venture 3.4 2002 .

[@motorcarnut]

Glad it helped, thanks for the comment

[@diycast6914]

How many inches did u have to raise it? Was it still a tight fit to remove and reinstall the pan? I may have to do this on my RWD van and am very reluctant to tackle this bear of a project

[@OldSchoolNoe]

Need one of these for motor mounts. I understand I can just jack up the engine and leave it on the jack......but now I see that this is a safety device in case the jack fails. Maybe I can just use my flat-top jack stands to place under the engine. Nah, might cause damage of the jack fails.

[@motorcarnut]

For the price and protection it’s a no brainier

[@sayekrahmankhankhan423]

can I use this to raise the engine? Or to lower it? I'm asking if it kinda would work like an engine hoist

[@motorcarnut]

It’s made to hold engine but it does raise and lower about 12 inches. It wouldn’t replace an engine hoist.

[@jordanwashington8950]

Did you buy a chain or you use the chains that was provided?

[@motorcarnut]

I use the ones that came with it and sometimes bigger ones too.

[@deebo2430]

Can i replace my head gasket using this tool?

[@motorcarnut]

Yes and a floor jack as well.

[@bleach_drink_me]

I got one of these, it's not terrible. A little dupont dry lube on the threads makes them feel a lot better and don't attract dirt. It's not perfect and the finish on mine had some bubbles out of the box, the welds aren't beautiful but they are holding ,for under $100 it's worth it. I also made and printed out of tpu those rubber spacers, just if I happen to lose one like someone did at my work.

[@motorcarnut]

Good tip! I agree for the price it’s fine, and I still use mine monthly

[@bleach_drink_me]

@@motorcarnut glad to see it has hung in there for you. I haven't used mine much. I try to avoid doing too much outside of work. Gotta relax and spend time with my wife and kids, you know. I have used it 3 times to change motor mounts on 2 and 1 to reseal a upper oil pan that requires the cross member to be lowered.

[@motorcarnut]

Thank you! And Amen to that , family first!