How to use a engine support bar, suspend the engine in the car while you remove the subframe. VOTD

In this video I unbox, assemble and install the Harbor Freight engine support bar or brace. This allows you to hold the engine in place on the engine compartment area while you remove the sub-frame or other parts under the car or truck.
Harbor Freight PN: 96524
-------------------------------------------------
Disclaimer: • In this video I share ...
Basic car care KZbin channel: / rspiwin
How to search my videos: • How to find videos on ...
Visit my Website for special tools, my wish list and other helpful information: www.RobertDIY.com
Support Robert, become a Patron: / robertdiyafterdark

[@benthemusicalchemist]

My clutch gave out, so here I am lol Also, this is a great video. In my opinion not enough videos bother to remind people that these things come with instructions.

[@RobertDIY]

Ouch! 😉

[@patrikfernfors1932]

Thank you for all your work putting up helpful vids on your channel!!👌👍👍

[@RobertDIY]

My pleasure!

[@Plane2TheT]

Sweet! Cheers for the video, just bought one today, looking forward to it helping with future projects. 👍

[@RobertDIY]

Have fun!

[@schnrck]

thanks, answered my questions! subscribed!

[@RobertDIY]

Thanks for the sub!

[@willmill409]

Robert how did you know I needed this video so I can replace my sway bar and lower engine mounts on my 08 xc90 LOL thanks for another great helpful video!

[@RobertDIY]

😆 You are welcome

[@0x00zero]

let us know if the bar was long enoug to work on XC90.

[@luke2042]

Thanks for the video!

[@RobertDIY]

You are welcome

[@uniquehorn1480]

Thanks, Robert.

[@RobertDIY]

you are welcome.

[@chemicalspore]

Nice vid. I bought one of these. Gonna put it to work

[@RobertDIY]

Nice

[@fiveable]

Perfect timing since I need to pull my transmission!

[@RobertDIY]

Awesome!

[@fiveable]

@@RobertDIY this is Tom. We spoke on the phone this week. Hope you got the “grease” I sent via cashapp. 👍🏻

[@RobertDIY]

thanks.

[@ChrislhJJ]

Thanka you for your valueble info for helping us rookiea

[@RobertDIY]

you are welcome.

[@maxnguyen22]

Nice work

[@RobertDIY]

thanks

[@laladamac]

My boy Afro Man . Sheeyee good video 👌🏽

[@RobertDIY]

😒

[@ButchNackley]

I built one out of wood to replace a transaxle on an 88 Z24. It worked just fine, but I'm going to buy one of these for safety.

[@RobertDIY]

good plan.

[@0x00zero]

Head's up HFT bar purchased feb 23 was too short to span a V70XC except at the very front, maybe 1-2 inches in front of the front engine hanger. I was surprised to find this video with the bar spanning the car in the normal place.....this car must be narrower than V70 or else bars got shorter.

[@RobertDIY]

thanks for sharing.

[@TheBlackSaloon]

Mister Robert! I’m about to do the same operation, I’m curious won’t the passenger side of the motor pivot down since the engine bar isn’t directly over the point where the chain loops through? Once the subframe is removed that is, and the weight of the motor is just supported by the bar..

[@RobertDIY]

I did not position the bar straight across. Besides that, what are your options?

[@TheBlackSaloon]

@@RobertDIY Exactly what I figured, other wise if the bar was straight across the points you loop the chain through aren’t directly under the bar. So the bar being diagonal across the engine bay is the way to go? One end by the passenger headlight and one near the driver hood hinge more or less.

[@RobertDIY]

yes

[@lamonttwitty2585]

Would this work for an inline motor?

[@RobertDIY]

Mine is inline.

[@lamonttwitty2585]

@@RobertDIY I’m sorry that was a vague question. I meant to say would it still work for a inline longitudinal engine that the run from front to rear instead of left to right.

[@tegimr]

@@lamonttwitty2585 Both front wheel drive and traditional engine installations (4 WD and rear wheel drive). Much better than a cherry picker in that it stays with the frame as you may need to adjust the body.

[@nicko6710]

Take the lever off?

[@RobertDIY]

Huh?

[@nicko6710]

@@RobertDIY off the transmission.

[@RobertDIY]

yes, that would help.

[@OEFarredondo]

I been working on engines for a while. No matter how many times I use stuff like this I still think of how many ways I can kill myself

[@RobertDIY]

Oh my!

[@caseydrake2729]

Uuuip

[@RobertDIY]

LOL

[@philliprose415]

Once you pull the subframe I would place a jack with a block of wood on top under the engine oil pan just as an insurance policy!

[@RobertDIY]

ok