PICK UP SOME NEW GEAR: theterracrew.com/ FOLLOW THE MEDIA TEAM: @james_x_edge @xoarshiaaa @nelsonflores__ @blackhat.studios @gxspice @nicksilke @jlow_l @morganclarkedesign1
Пікірлер: 38
@Samophlan3 жыл бұрын
Need to school us on wheel hubs next. Front and rear. Along with brake assemblies.
@cmanuel819893 жыл бұрын
Need more of this. Want to learn and eventually build my own pre-runner.
@rosyboiztv49523 жыл бұрын
Nice, I always wondered how a full float axle set up worked!! Good informational video!!
@drtone3 жыл бұрын
Torino?!! .....what Pick-a Part yard has 50 year Torino there for snagging the 3rd menber, lolol. Great video, awesome !
@imFrawst3 жыл бұрын
You guys have the best friends everyone super nice and knowledgeable
@imFrawst3 жыл бұрын
You guys have the best friends everyone’s super cool and knowledgeable
@Gannjo933 жыл бұрын
Loved this video. Shows how much I don't know
@randywilliams43253 жыл бұрын
Just set up a Gm 12 bolt truck axle before watching this on my lunch break .
@anthonyolsen92993 жыл бұрын
Nice video..
@brandonruddick23063 жыл бұрын
I like that Datsun in the background
@stevewilcoxson71733 жыл бұрын
Thanks! I was thinking about a junkyard Explorer swap For my Ranger. But I did not know all of that.
@blkscorpion013 жыл бұрын
They have C-Clip eliminators if that was a worry you had about running an Explorer Axle
@stevewilcoxson71733 жыл бұрын
@@blkscorpion01 I didn't know that.. But will definitely look into doing that. Thanks.
@bird4dbk4203 жыл бұрын
🌵Awesome video 🍻🌵
@traviskarrle5033 жыл бұрын
super informational vid broham 🤙🏽😎
@coolman24313 жыл бұрын
unreal
@mrjivester3 жыл бұрын
So much good information. I should have gone with a full floater. Can I upgrade to a Full Floater from a semi-floater on my Currie F9 3.5" tube axle?
@guambomb6713 жыл бұрын
🤙
@davidmays33333 жыл бұрын
Nice job
@ruubguus43213 жыл бұрын
👍
@gafrers3 жыл бұрын
Needs to do the same about front solid axles next
@chuckiedodd933 жыл бұрын
That Z tho.
@DreamTruckStuff3 жыл бұрын
Who makes the best shafts
@felixpadilla52883 жыл бұрын
Is there a walk around on black hats 4thgen 4Runner ?
@christianborgwar6663 жыл бұрын
I want to see that as well.
@blackhatstudios24413 жыл бұрын
Sooooon! 🤙🏻🤙🏻🤙🏻
@usMarinecuv9023 жыл бұрын
Anyone have opinions on gear ratios and tire size? Obviously that depends on vehicle use, hp, rpm range, transmission, etc, but can anyone drop down what they're running? Right now I have a 2001 dodge dakota 4.7l v8. 230hp at 4,600 rpm and 290 tq at roughly 3,600 rpm. (From what I could find for a stock 01 4.7) I'm getting 4.10s installed and I'm running 33s. Right now it's a daily, but want to build out later.
@thezombikilla3 жыл бұрын
4.10 will be a good all around gear with your setup. If you go to bigger tires and want more offroad only use then something like 4.88 or 5.13 would do you good.
@usMarinecuv9023 жыл бұрын
@@thezombikilla yeah, I'll run this setup for a while and see how I like it. I'll definitely be moving up to 35s the next set of tires and run the 4.10s for a bit until I can decide if I'll stop at 35s or move to to 37s ha. For sure if I go 37s ill change to 4.88s, but I don't know if going to 4.56s for the 35s is worth it if I end up going 37s ha
@anthonyolsen92993 жыл бұрын
I have 500hp.. 3,000 rpm stall..35's on a 4 link truck.. I'm running 5:13.. so I still have decent road speed..and decent dirt manner
@aju33073 жыл бұрын
@@usMarinecuv902 i have a WJ with same engine/tranny as you. 37's on 1 tons with 3.73s, gonna move to 5.38s. previous axles i had 5.13s with 32s and was fairly happy with it.
@dhrracer3 жыл бұрын
Coatings and or finishes on gears? Oil choices?
@dobermanracing3 жыл бұрын
Cryo treat the gears and bearings. 85w140 redline gear oil.
@dhrracer3 жыл бұрын
@@dobermanracing Any body doing REM finishes? I had the opportunity a number of years ago to visit a number Nascar shops. Did not get to go into Penske's gear room but could see into and every gear (trans and axles) were REM finished. And all the teams were running a ball/convexed shaped splined axle at wheel end to enable to shim spindle for both toe and camber.