Ransoto - Anodizing Exhaust Installation For Yamaha MT 07 - FZ 07

[@MotoRider2]

The white covering on the bracket that is mentioned in the video is just plastic. Make sure to peel it off. Also, if you're looking for this exhaust on Amazon it tends to go out of stock quite a bit. There are two alternatives that look the same. Although, I WON'T guarantee they are the exact same as the Ransoto/Anodizing version. This is the link to the actual Ransoto/ Anodizing exhaust - amzn.to/3fkJbe8 If that's out of stock try this...amzn.to/3DH5s4n Or this...amzn.to/3RzVcAR

[@FoamSquatch]

I like how you went back through the different sounds again. Sounds good with the baffle in, but man, without it...... that takes the cake.

[@MotoRider2]

Definitely. I really enjoy how it sounds

[@syruslife]

i kno the vid is 2 years old but mine just came today. I hope you eventually realized the white around the bracket is actually just a protective sticker for the chrome. apologies if its already been mentioned in the comments. thanks for the vid :)

[@MotoRider2]

Yep. Realized it as soon as the video was uploaded. Enjoy the exhaust.

[@MultiElement21]

My neighbours gonna love this exhaust

[@JustAMindlessDrone]

I've run this exhaust for almost 5 years. 100% tune your bike with power commander or a flash if you plan on keeping your bike for many years. The baffle needs to be out to get the HP gains. It's actually quite alot with the snorkel off. Very noticeable in the top/mid end, didn't notice any low down gains. The exhaust has started to rust. Also the exhaust isn't properly aimed away from the bike so soot builds on swing arm and spool on that side. I actually took the exhaust off last summer and put the breadbox stock exhaust back on and remapped for it. Though going to put it back on today as I don't tour much anymore. Sound does get annoying after 3-4 hours on the highway. Before you try to remove the exhaust nuts on an older bike might want to warm up the exhaust first or soak in a penetrating oil of some sort a day or two before. Last time I did the job the whole stud came out of the head and all the nuts have started to corrode over the years. I went thru ali express instead of just paying for re-seller on amazon. Saved quite alot but obviously take longer for shipping. Valuewise this is quite a deal but keep in mind running this pipe long term untuned long term will probably cause some damage. It was overheating alot sitting in traffic, also bike got very noticeably slower with tons of decel popping while untuned as well. If I ever would do this again, I'd get the flashing kit and go with a better exhaust like Akrapovic. Flashing kit gives you so many more options other then just fuel mapping like fan cut in/cut off, amount of engine braking, etc. Or just get the MT-09.

[@MotoRider2]

This is a great overview. Thanks for sharing. I agree that there should be some sort of tune. Whether you use a power commander or send it out to be tuned would be good. Mine is still in great shape after all these years. But I also wipe mine down after every ride. And yes, it's loud. After a few hours, it can get annoying, even with ear plugs.

[@omarcarrillos2727]

Thanks for all the info.

[@Ghostsoulless]

If anyone has this and wants a bit more noise without the unrefined sound of no db killer at all, you can take the end cap off the db killer. Gives a nice middle ground that’s loud but not obnoxious like no db killer is (imo). Think it has the best exhaust note this way

[@iUnloadMags]

Really well done video dude, I appreciate the quality 👌

[@MotoRider2]

Thank you. I'm glad you like it.

[@asaprocko9108]

facts

[@omarcarrillos2727]

It sounds good with baffle in. Thanks for all the info. In the description.

[@MotoRider2]

Yeah it does. In person it sounds ridiculous (in a good way) with it removed.

[@kxcrunner7]

Got mine today! We’ll definitely be using this to help with the install!

[@MotoRider2]

Awesome. You'll love the sound once it's installed.

[@RoamWithAli]

Thank you so much brother, its one of the best video of installation on KZbin. I have been looking for that Universal Joint Set but didn’t know which one was the right one. So thank you for putting the links in the description.

[@MotoRider2]

You're welcome. Glad it was helpful.

[@ultra727]

Thank God I came across this video, I'm getting an R7 when they come out in Australia in 2 weeks. This will save me so much $$ 😄

[@MotoRider2]

Awesome. Glad it was helpful

[@WIRCinc]

Thank you sir. Just finished. Sounds pretty good. For less than 200, you cant beat that with a stick.

[@MotoRider2]

Awesome. Enjoy it.

[@boyanlu7927]

the holder bracket has a white protect film on it, you can just peel it off so it will become chrome, it is not painted white

[@MotoRider2]

Yep. thanks for the heads up. I realized that as the video was uploading and I placed a note about that in the description

[@trruplayaa01]

Good video man. I bought the same thing and that white thing on the clamp your talking about is just a plastic cover. Take it off and it will match with stainless look 👌

[@MotoRider2]

Thanks. I realized right after uploading the video about the white plastic cover. Took it off and it all looks good now.

[@blank.e4327]

Without baffle its sound much good

[@MotoRider2]

Yes it does.

[@nimashali9076]

For best performance, i highly recommend that you MAP ur ECU. Also change the Air filter to DNA. You will lose power by just changing the exhaust, i did a full remap and the bike was much more responsive.

[@MotoRider2]

Yeah. I'm no tech pro so flashing the ECU was the best bet for me. The snorkel was removed from the filter and runs really well this way.

[@jericmillarez941]

Nice video bro, about the white paint on the bracket, it’s actually just a wrap cover you need to peel off, i did that to mine.

[@MotoRider2]

Thanks. I noticed it was a plastic wrap right after uploading the video. Haha, ended up adding a note in the description after that.

[@AR-3618]

Great instructional video. Just got mine in the mail today, cant wait!

[@MotoRider2]

Thanks. Enjoy it.

[@addyedward6632]

Just did this step by step with your video. Many many many thanks!

[@MotoRider2]

You're very, very welcome

[@REBRIDGES1212]

Nice video! Just put mine on today that white on the strap should peal right off I did on mine it’s just a protective coating

[@MotoRider2]

Thanks. I realized that right after uploading the video. Peeled it off, and then left a note in the description mentioning that.

[@SkiPump]

Awesome video. Gonna order this exhaust soon for my 2020. I appreciate how easy this video is to follow!

[@MotoRider2]

Thanks. Glad it was helpful. It always frustrated me when "how-to" videos skip steps. So I wanted to make sure this didn't do that.

[@SkiPump]

@Yugo RC I just installed it over the weekend and got my ECU back from 2WDW today. Gonna try it out tomorrow!

[@mouradchibane1818]

Awesome detailed video!!! Perfect, thanks a lot!!

[@MotoRider2]

Thanks

[@harminder87]

I just installed the exhaust today ur video was great help man!! Appreciate The bike sounds really dope when rev matching!!

[@MotoRider2]

Awesome. Definitely sounds way better than stock. That's for sure.

[@petesmall4360]

thank you far making this video. helped make it an easy install.

[@MotoRider2]

Sure thing. I'm glad it was helpful

[@AICD1999]

The clamp is silver. That white is a protective over and comes off easily

[@MotoRider2]

Yep. I realized the moment I uploaded the video and let everyone know in the description.

[@avertaze6604]

This helped immensely when installing on my 2019. Now my wife doesn't make fun of me driving something that sounds like a moped anymore!

[@MotoRider2]

Yeah. The angry sewing machine sound had to go lol

[@sharkrape]

Super well put together video dude. 10/10

[@MotoRider2]

Thanks. Much appreciated

[@esosic]

Hey that white stuff is supposed to come off you got a nice chrome finish under there!

[@MotoRider2]

Yep. Realized that right after the video was recorded and posted. So I made a note about that in the description. Thanks

[@rogervalkenburg9328]

Great video and helped immensely when I installed one on my 700 Tracer, thanks.

[@MotoRider2]

Thanks. How's it looking and sounding on the Tracer?

[@rogervalkenburg9328]

MotoRider The exhaust sounds great; a great deep throated burble at idle & slow to medium acceleration, a real growl when the throttle is opened up. A little popping in the low gears on deceleration, quite normal I’m told and not harmful to the engine by my local Yamaha dealer. Having the ‘noise’ when accelerating actually makes gear changing easier & smoother; great going through the mountains😀

[@MotoRider2]

@@rogervalkenburg9328 - Awesome. if you get it tuned the "popping" will go away and the bike will actually pull a bit harder in the mid rang.

[@lemello18]

@motorider the exhaust holder white part peels off to chrome under it.

[@MotoRider2]

Yep. Figured that out after the video was uploaded. There's a note about it in the description for others as well so they realize that.

[@justinwilkerson4697]

Sounds good!

[@MotoRider2]

Thanks

[@fantazykory]

You suppose to peel that white protective layer off. Lol🤪🤪

[@MotoRider2]

Hahaha. Found that out later. Too late to change the video now lol!!!

[@stefanplayngo5430]

Bro I hope you realized that that is white protective film over the muffler bracket and you had to peal it off :) Otherwise a very well detailed video

[@MotoRider2]

Yeah. As soon as the video was uploaded I realized that. Even posted an update about it in the description when the video was uploaded.

[@vikingplisken6241]

Great video helped alot after i have just installed one and it sounds like an absolute beast with this i didnt take off the db killer but its probably even better :D

[@MotoRider2]

Yeah. Has a deeper sound without the db killer. And of course, it's louder lol

[@j.m.b3987]

Appreciate your video thank you 👍🏾

[@MotoRider2]

My pleasure!

[@hbfilms357]

Good video man. Well done, I have the same exhaust on my bike

[@MotoRider2]

Thanks man. How's it been holding up for you?

[@hbfilms357]

So far so good!

[@mrh8409]

How do you remove the baffle besides taken the bolt out of the front?

[@MotoRider2]

There's a bolt right on the back tip (bottom) of the exhaust that comes right out. Super easy

[@Robocoppat]

What what's the final verdict as far as performance goes? Did you keep the db's out or put them in? It really sounds healthy. I just got a brand new 07. Looking forward to doing some work to it. I'm on the East coast as well. 👍😃

[@MotoRider2]

I did a follow up video a year later that goes into all of that. Here's the link... kzbin.info/www/bejne/mWnKepuladCoidE And congrats on the new 07. You'll enjoy it.

[@jimwilson9613]

Nice video. This helped me today when I installed mine. Did you notice any difference once you had the tune?

[@MotoRider2]

Yes. No popping when accelerating. And it seems the mid range seems to pull a little harder.

[@crazyman4207]

Where did you find gasket sealant that goes above 1000 degrees? Only copper gasket sealant i have found goes up to 700

[@MotoRider2]

I didn't. I just used the one in the video. I've had no problems with it up to this point. If there is a leak from the sealant wearing off, I'll just apply more of what I used.

[@antwonboonk3540]

What power commander tune would I upload for this exhaust?

[@MotoRider2]

Not sure. I had it sent out to 2 wheel dyno works to have the ECU flashed. That worked great!!

[@uncletorr]

Like Cody c said well put together vid. Did you reflash your ecm after. If not how does it run. People are back and forth about it and I almost don’t want to lose the engine braking. I’m used to it

[@MotoRider2]

Thanks. The ecu was flashed by 2 wheel dyno works. I liked the engine braking and was worried about it being eliminated with the tune. But the engine braking didn't go away after the tune. It just made it a bit smoother when letting off the throttle. Not that real jerky motion. As for how it runs, it runs great. No backfiring, and it pulls better in the mid-range.

[@uncletorr]

MotoRider My buddy was saying “2WDW” doesn’t do the flash for the 2020 mt07. Obviously they do I’ll look into it. Thanks for the reply ☝️

[@jwro1296]

Hi MotoRider, I purchased this exhaust after seeing your video. Question, Should i most def get it flashed before taking it out for a ride or can the flash wait? One more question, do you have the baffle in now or did you end up leaving it out? Thanks for the time!

[@MotoRider2]

I rode it a few times before getting flashed. There was definitely a loss in power and it would backfire with and without the db killer. So for me I didn't want to deal with that so I got it flashed right away. I'm not a mechanic so I couldn't tell you if not flashing it will hurt anything in the long run. All I can say is that the flash made a world of difference.

[@jwro1296]

@@MotoRider2 Thanks!

[@dakotabingham13]

So I have this same exhaust , and I have a power commander fc , any recommendations on what tune I should be used ? Got the bike with this set up and want to make sure it’s running properly .

[@MotoRider2]

No idea. I'll be sending the ecu out to be flashed.

[@normfry2187]

Hey, I’m getting a 2018 with this setup this week and wondering if you have any feedback on how it’s running or if you got it tuned. I wanna make sure my new bike is running properly. Thanks

[@eastcoastpikachu]

I havent installed my exhaust yet but notice in the baffle there is a cap you can unscrew does yours have the same if so have you tryed it with out the cap baffle installed?

[@MotoRider2]

Yep. If you watch until the end of the video you'll see what it sounds like with and without that cap (db killer). I run it without the db killer.

[@crazyman4207]

Bro🤣. That white out is a sticker to protect the chrome. Its silver underneath

[@MotoRider2]

Yep, realized that after the video was shot. I immediately left a note about that in the description section when the video was loaded.

[@fernandoperez2513]

Excelente descripción. Gracias!

[@MotoRider2]

De nada.

[@lukegreeley1056]

Hey man, did you have a metal reducer piece in the muffler that you needed to take out before attaching to the headers? Mine does, wondering how you got it out

[@MotoRider2]

Nope. I didn't have anything like that. The muffler slid right on to the pipes.

[@kurajek33]

Do you get some cartificate with it, i need to know cause if it don't contains any of that in europe i cant homologate it. PLS i need help.

[@MotoRider2]

Don't know what certificate you're talking about. Didn't get anything like that. It does come with a "db killer" which reduces the decibels though

[@josealbertoguzmansantoya1882]

Good video bro. when you put a full system exhaust you must tune the bike or is it not necessary?

[@MotoRider2]

I'm no pro so I couldn't answer that for sure. Some people say no, some say yes. I look at it this way, if the bike is programmed to run a stock exhaust then it's not programmed for this exhaust. So I'll be tuning it.

[@josealbertoguzmansantoya1882]

MotoRider thank you!!!. How do you fell the bike now? More power ? Less power? or the same like before and just change the sound?

[@MotoRider2]

@@josealbertoguzmansantoya1882 - Just installed the exhaust the other day and haven't ridden it much yet. I'll know how it feels when I take it out for a good ride. It definitely sounds WAY better though. It's really loud with the baffle out.

[@josealbertoguzmansantoya1882]

MotoRider perfect bro, you have to do other video riding with the new exhaust and tell us how do you fell the bike 👍🏻. I got a MT 07 too and I want to put the same exhaust 😍

[@antoniosimental8978]

Only one gasket came off (the one on the right). I tried putting the new gaskets on both sides but it would not fit with the gasket on the left. Am i tripping or is that how it is?

[@MotoRider2]

Both gaskets should come off. It could just be the gasket is stuck in there. You may have to get a tool in there to pull it out. Also, the pipes could be a little wider than the slots so they don't fit perfectly. A little muscle to push them closer together will help them fit. I had to do that slightly.

[@antoniosimental8978]

Also, it did not come with some pieces that you received but we made it work. Appreciate it!

[@MotoRider2]

@@antoniosimental8978 - Glad you got it to work out. I've heard that sometimes it doesn't come with everything.

[@kingpinestudios]

How can i pick one of these up? Seems to have been taken down

[@MotoRider2]

Yeah. With the craziness of the past year sometimes they're available and sometimes they're not. I'm guessing it's supply chain issues. Hopefully, they'll have some more soon. You'll probably have to keep checking to see if Amazon has them.

[@Mononoken]

Very pro video here. What ECU map did you use?

[@MotoRider2]

I send the ecu to 2 wheel dyno works. Had it back to me within a week. Runs great with their tune.

[@DL-sy5fv]

@@MotoRider2 what map did they use?

[@louvega8414]

Great vid, thanks!

[@MotoRider2]

Glad you liked it!

[@deivydasindriulis6229]

Hello just found your video, thank you for tutorial, wanna ask maybe you know did is fit 2020 yamaha mt07 model?? Thanks

[@MotoRider2]

Yeah, it should fit.

[@REBRIDGES1212]

Fits for sure just put on mine!

[@blastedup1953]

Did you lose any low end power from the slip on ?

[@MotoRider2]

Before the flash it may have felt slightly less "powerful" but not much. Oh, and this is a full exhaust, not a slip-on.

[@kkush82]

How has this exhaust held up so far. Mine will be here this saturday. Won't get a tune for it until a month later. Will this hurt the bike. I use it daily to commute to work. Tia

[@MotoRider2]

It's held up great so far. I'll be doing a review on how it's held up soon. As for not having it flashed I couldn't tell you if it will hurt the bike. There are a lot of people who haven't. But in my opinion, a flash is worth it and it's not that expensive. It wakes the bike up and just runs better.

[@MotoRider2]

Just posted the 1-year review of this exhaust - kzbin.info/www/bejne/mWnKepuladCoidE

[@JAYJAY1787]

I've been seeing with the baffle in you won't need a tune , that baffle out sounds overwhelming but nice but still to much

[@MotoRider2]

It's definitely better with a tune for sure. Baffle out is loud, but I wear ear plugs so it doesn't bother me at all.

[@mr2goulart-mineiro113]

Very detailed video, thanks for posting. 👍 subscribed

[@MotoRider2]

Sure thing.

[@NES-6-25]

Do you still have your bike? What’s the year review of the exhaust?

[@MotoRider2]

Yep. Just posted that exact video...kzbin.info/www/bejne/mWnKepuladCoidE

[@DaniWhiteMoto]

What's the one month consensus? Looking at the same company for my FZ-09..

[@MotoRider2]

Very happy with it. Definitely worth getting a tune for it.

[@jdonfireofficialmusic5037]

Will it need a tune up?

[@MotoRider2]

I'd recommend getting the ECU flashed. It will run much better with it

[@DeXx_The_Reaper]

Sounds better with Db killer

[@sethhartman8804]

Someone on Amazon said it's leaving discoloration on the swing arm, is this true?

[@sethhartman8804]

Okay thanks man

[@MotoRider2]

I'd heard of that as well and was concerned when purchasing it. But so far I don't see anything. I've checked to see how hot the swing arm gets because the exhaust points at it a bit and it only gets "warm." I also just make sure to wipe down after riding. But so far, so good.

[@brovayurbee6102]

Do you need a tune after this process?

[@MotoRider2]

I'm no mechanic so I couldn't say if you "need" a tune. But I had it done and it makes a big difference in how the bike performs. And it's not that expensive so I'd say give it a go. Check out the review video on the exhaust you'll hear a bit more about this.

[@brovayurbee6102]

@@MotoRider2 will do, thanks.

[@bertobubba]

Nice joob dude

[@MotoRider2]

Thanks

[@miguelcarongaboury1991]

How we remove the baffle?

[@MotoRider2]

There's a screw on the bottom that you just unscrew.

[@miguelcarongaboury1991]

@@MotoRider2 ok thanks and nice video

[@michaelogg1254]

That’s an Amazon exhaust

[@MotoRider2]

That's one of the places you can get it

[@BriceTooNice]

mine rubs the swingarm

[@MotoRider2]

You should be able to bend it just a bit to reposition it

[@BriceTooNice]

@@MotoRider2 i tried but it was getting sketchy lol. I just got some layers of some heat resistance tape where its rubbing at for now

[@Miguel-ng5wm]

Mine don't match the headers wtf. I will have to bend them. And yeah it's the correct model.

[@MotoRider2]

Yeah. I've heard that happening here and there. In fact I made the mistake of testing to see how they fit before putting the new gaskets in. Hahaha, that was a mistake. I got them in pretty easily but couldn't get them out. Took a lot of muscle but was able to get it eventually.

[@mooiboyace]

These Chinese mufflers for the MT07 sound horrible

[@MotoRider2]

To each their own I guess. I'm pretty happy with mine

[@noahphelan2182]

Thank you for the video. It was super helpful for the install.

[@erock639]

Glad it was helpful.