Instruction on how to replace rear axle bearings and removing axle on a Jeep Cherokee XJ with a stock Chrysler 8.25 Differential www.autooneled... use code "Majorweakness " for discount on led bulbs
Пікірлер: 90
@davel3402 Жыл бұрын
This is a great video - Thanks to you I just replaced both rear axle bearings on my '99 Cherokee XJ. Trickiest bit was getting the new bearings/seals in - that took some hammering! This is a great guide for someone who hasn't done the job before, and really appreciated. Also it really helped that you identified the tools used and the Lucas Oil etc... I couldn't rent the slide-hammer/remover here in the UK, but I was able to buy them and it's still cheaper than a repair shop! - thank you!
@MajorWeakness Жыл бұрын
Glad it helped and your repair a success
@foxfloot Жыл бұрын
Thanks for this, doing this repair on my 99 next weekend
@MajorWeakness Жыл бұрын
Hope it helps
@pererikbertholdsson8645 Жыл бұрын
Really informative thx a lot, greetings from Sweden!!
@MajorWeakness Жыл бұрын
Thank you. Greetings from USA!
@Suberten Жыл бұрын
I was looking for a jeep xj rear axle replacement video and this one just pop up. Really nice and simple explained. Going to do mine tomorrow. thanks!
@MajorWeakness Жыл бұрын
Glad it helped
@98LS12102 ай бұрын
Thank you
@MajorWeakness2 ай бұрын
You are welcome
@Timw00d13 Жыл бұрын
Super helpful thanks so much for this!
@MajorWeakness Жыл бұрын
Glad it helped
@girlgolden84912 жыл бұрын
FREE tool rentals? That’s GROOVY!
@joshuazientara44522 жыл бұрын
Thank you for sharing.
@MajorWeakness2 жыл бұрын
You are welcome
@OliverParilla-k2k7 ай бұрын
Bieautiful video thenks 😊
@MajorWeakness7 ай бұрын
thanks
@darrellspinner7154Күн бұрын
Great video but let me ask , I have a 1984 jeep Cherokee pioneer with select-trac. I guess this video does not apply to the select-trac model ? the gearing in the differential housing was more complicated than in this video so I decided not to proceed any further. Thanks Spinner
@MajorWeaknessКүн бұрын
A 1984 cherokee had a different axle. Probably an AMC 35 or Dana 35. Mine in this video is a Chrysler 8.25
@bobsilver39833 ай бұрын
At a dealership near me is a 2006 Jeep Grand Cherokee with only 44,000 miles and the dealer says its on a lift and they have to replace rear end bearing because they heard howling while driving it. How could bearing go bad at 44,000 miles? Does this sound right? Other than that the Jeep is insanely nice.$11,500 for it.
@MajorWeakness3 ай бұрын
Could be age if the jeep sat in one spot for a long time or if it was pulled behind an RV where it has a lot of miles on the axle bit not registered on the computer
@GKirkland1 Жыл бұрын
I have 1997 Grand Cherokee Loredo. Is this process the same or do I have to press em on the axel shaft?
@MajorWeakness Жыл бұрын
See if you have a Chrysler 8.25 rear Differential. If you do then it's the same procedure
@nalvarez35053 ай бұрын
Exelent video thank you sir!
@MajorWeakness3 ай бұрын
You are welcome
@tristanhawkins175124 күн бұрын
Awesome video brotha thanks
@MajorWeakness24 күн бұрын
Thank you
@1stNightingale Жыл бұрын
Hi there, fantastic work, i'll be using your video as a walkthrough, but i have a Dana 35. Just wondering if you've done the inner seals as well and if they are the same as the outer?
@MajorWeakness Жыл бұрын
Thanks. I ve never done inner seals
@OvertravelX Жыл бұрын
Been a while since you've asked, but there isn't an inner seal on the rear. The gear oil runs all the way out to the end of the axle tubes to lubricate the bearing he just replaced. Hence the outer seal.
@danhambrick63312 жыл бұрын
Nice job Major.Cant wait to see this cross country trip you are taking.👍👍😁😁
@MajorWeakness2 жыл бұрын
It's definitely going to be interesting!
@chrisbragg30848 ай бұрын
Thank you for this DETAILED video and explanation of EVERYTHING YOUR TOUCHING in the video….you helped me get my sitting 91 cherokee drive (somewhat normal) again 🤣🙏🏻 thank you!
@MajorWeakness8 ай бұрын
Glad it helped!
@stephenpatton8690 Жыл бұрын
Spray the hell out of that thing! Wipe. Spray. Repeat
@Blairzboy11 ай бұрын
My 93 Cherokee had a Dana 35 that 12 point bolt holding the pin in was a 1/4 inch wrench everything else was the same
@MajorWeakness11 ай бұрын
I don't have any experience with the D35
@Spruce-Bug2 жыл бұрын
Fantastic video, Thank you!
@MajorWeakness2 жыл бұрын
Thank you
@Justin-s1m7l10 ай бұрын
How to put the rear brake drums
@MajorWeakness10 ай бұрын
Don't have a video on that
@cbrunnem610211 ай бұрын
worried about starting the bearing dry but stick your dirty fingers all in it and set the bearing in your dirty pants. dirt will kill a bearing extremely quickly.
@MajorWeakness11 ай бұрын
I've had to replace them 3 times since this video
@henrylewis608 Жыл бұрын
Buy on bag of gear oil and 2 bottles and you can fill the bag up. Great video tho. Looking doing this soon
@MajorWeakness Жыл бұрын
That's what I did on my other XJ!
@kennysmith9987 Жыл бұрын
Well idk if you’re luring me into false confidence but this looks super simple and I’m gonna attempt to do it myself
@MajorWeakness Жыл бұрын
Really not complicated. Hardest part is the seized bolts. Be very careful with heating bolts. Of course I cannot recommend using fire near your fuel areas!
@kevinritter4932 Жыл бұрын
Would the dana 35 in the rear of my 1990 yj be the same disassembly procedure?
@MajorWeakness Жыл бұрын
1990 could have c clips or not. I believe it was transition year. If it has c clips then should be similar
@CharlieRoamin3 ай бұрын
Very Good video - !!!!
@MajorWeakness3 ай бұрын
Thank you
@alecsithong Жыл бұрын
Excellent work Major! It was well done and clear to do. Thanks so much!
@MajorWeakness Жыл бұрын
Thank you. Glad it helped!
@JeffJones-om2nh2 жыл бұрын
Made it look super simple!! Thanks!!
@MajorWeakness2 жыл бұрын
Thanks
@losdelujoraulbotello4555 Жыл бұрын
Gracias a tu video voy a cambiarlo yo mismo comprare las herramientas apropiadas thanks a lot
@MajorWeakness Жыл бұрын
Glad it helped
@jdean1851 Жыл бұрын
THANX from 20f Idaho! Great job"
@MajorWeakness Жыл бұрын
Glad to be of help
@tnqualified6349 Жыл бұрын
Fantastic Video, Took about half an hour thanks to you. Thanks!
@MajorWeakness Жыл бұрын
Glad it helped!
@TalesoftheScales Жыл бұрын
How much would you charge for this ??
@MajorWeakness Жыл бұрын
About 500.00 but I'm not a professional mechanic
@mehmetdurmus90169 ай бұрын
Super
@MajorWeakness9 ай бұрын
Thanks
@RyanDickinson-m1g11 ай бұрын
Is it the same for both sides?
@MajorWeakness11 ай бұрын
Yes
@joeordinary209 Жыл бұрын
Regarding bearing prices, in Rockauto, the price range is from 5(Schaeffler/ FAG) -38(Mopar) usd each...still well known brands, any particular to avoid? Or to recommend?
@MajorWeakness Жыл бұрын
I have experience with National, Moog, brand. I can't vouch for others. You can't go wrong with the oem mopar if u are doing stock. Try Morrisb4x4 for other brands.
@joeordinary209 Жыл бұрын
@@MajorWeakness Thanks!
@isaacjanness7897 Жыл бұрын
SKF is another great option, they make lots of bearings for the industrial world
@MajorWeakness Жыл бұрын
@@isaacjanness7897 true!
@isaacjanness7897 Жыл бұрын
@MajorWeakness I've used SKF front hubs on my brother's Comanche, and I just replaced my clutch throwout bearing with and SKF. The quality is definitely noticeable just by looking at the parts right out of the box
@oomfh Жыл бұрын
I have a hum in my left front suspension. Replaced wheel bearing, U-joint and a partially seized caliper. Invested in a Steelman wireless chassisEar and determined I need an AXLE bearing. Have you replaced a front AXLE bearing on your Cherokee? If so, is the procedure, tools close to being the same? Thx
@MajorWeakness Жыл бұрын
www.quadratec.com/jeep-replacement-parts/cherokee-xj/xj-dana-30-front.php See diagram from link. It could be #10 or #2 making the noise. You might want to move the listener near #2 to see of louder. Somewhat a different procedure. I haven't changed on mine as of yet.
@ky06112 жыл бұрын
How do you know if the bearings are bad?
@MajorWeakness2 жыл бұрын
Normally you would hear a humming or grinding noise. Also if you hold the tire try to move and test for play that is another way.
@michaelfrench3435 ай бұрын
Great video very informative.
@MajorWeakness5 ай бұрын
Thanks
@moejr14 Жыл бұрын
What were your symptoms
@MajorWeakness Жыл бұрын
No noise symptoms. Just a leaky seal. Gear oil in my brake drum. Decided to replace bearings since I was about to drive across country
@ralphnabozny8494 Жыл бұрын
This guy is very good
@MajorWeakness Жыл бұрын
Thanks for watching
@dealinwithit1 Жыл бұрын
great vid
@MajorWeakness Жыл бұрын
Thank you
@Appalachian_Asshole Жыл бұрын
Those collapsible bottles are great but if you don't have them or a pump I'll drill a 20oz coke lid to fit about a foot hose in it that reaches almost to the bottom of the bottle and still have a few inches sticking out the top making a squeeze bottle pump hopefully someone finds that useful