Relearn TPMS on GM vehicles without a TPMS tool

If you would like to leave a donation here is a link ...
www.paypal.com/cgi-bin/webscr... This procedure was performed on a 2012 Chevy Cruze but its the same procedure for almost every GM car out there.
IF YOU HAVE ANY QUESTIONS JUST ASK!
** If the video was helpful, remember to give it a "thumbs up" and subscribe. **
If you would like to leave a donation here is a link ...
www.paypal.com/cgi-bin/webscr...
Follow me on INSTAGRAM
/ falcons_garage
Twitter.
/ falcons_shop
Garage's Facebook
/ falcons-performance-an...
Facebooks Hobbies
/ falconshobbies
My Gaming Channel.
/ @falconsgaming
Disclaimer:
Due to factors beyond the control of Falcons Garage, I cannot guarantee against improper use or unauthorized modifications of this information. Falcons Garage assumes no liability for property damage or injury incurred as a result of any of the information contained in my video. Use this information at your own risk. Falcons Garage recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Falcons Garage, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Falcons Garage

[@SuicidalNapk1n]

Though there are some other videos that explain this, yours is the best. The fact that we don't need that stupid tool is excellent. Thanks for this!

[@FalconsGarage]

Glad it helped

[@glenkorsen6864]

Thanks! Worked perfectly in my 2011 Camaro 2LT with TPMS installed in Scorpion snow tires from TireRack! Much appreciated.

[@major4415]

Glen Korsen would this be the same for my g8

[@BooklessT]

Love the fact that he's wearing a Ford cap! Good video, easy to follow.

[@johndeaton1786]

Thank you so much. You saved me a trip to the dealership.

[@rafaelmartinez5434]

Great video! Simple and straight to the point! Thanks!

[@so_DarlingAnn]

Thank you so much! This video helped me get rid of the flashing tire light. One of my tires wasn't showing up on the system even though I put air on it. I put air on it following the air pressure labeled on the tires and followed this video and worked wonders ^^

[@FalconsGarage]

Glad I was able to help!

[@cbjueueiwyru7472]

Thank you so much for this. Worked perfect! I was about to buy a TPMS tool when I came across your video.

[@moniquehampton8330]

]

[@zenspike8246]

Thank You Bro. You just saved me a lot of money. My wife's 2010 Chev Malibu just had a complete tire change. A day later the TPMS warning came on. She was on the freeway and in very dangerous snowy conditions. It showed her front left was out of air. When she called the tire company, Discount Tire, they told her that her sensor was bad. After viewing your video, I reset all 4 tires.... and bingo, resolved. These company's all want to charge you for replacement of the sensor. It's an industry rip off. Discount should have reset the system at the time of the change of tires, they know that. Just like re setting the oil life at an old change. Again, thanks Bro.... easy fix !

[@FalconsGarage]

Glad I could help!

[@jamesszalla4274]

The amber tire icon will generally flash if there are bad sensors. If it’s solid, it generally means tire pressure is low or the system needs to be reset. You can actually pick up a reset tool online for around $10.00. It’s a lot easier way to reset the system for a small investment. Additionally, some GM vehicles will reset themselves. Inflate the tires to the proper level and drive the vehicle 20-25 miles at 50+ MPH. Again, you can only reset the system if the amber tire icon is on steady. If it’s flashing, you have bad sensors or some other system failure beyond low tire pressure Discount is usually pretty thorough. Your wife’s system probably went into some kind of automatic relearn cycle after the tires were changed. Had a Ford Transit Connect van that would do that.

[@ryanmaggio6711]

Thank you Sr much appreciated, just got new rims and now I can turn my check engine light off, your the man!

[@FalconsGarage]

Glad I could help

[@blackmetalchevy]

This is probably the coolest thing ive learned about the cruze im glad its easy and no tools needed thanks for the video!!👍👍

[@FalconsGarage]

Glad it helped!

[@2Twinado1]

So you loosen the valve cover until the beep and retighten?

[@reycornell9447]

2011 Chevy Cruze LT: Thank you so much, this actually works! Only took a few minutes my low tire pressure light went off after i put air back in the tires that was alerting low pressure. Thanks bro

[@FalconsGarage]

GLAD i COULD HELP!

[@sheerasingh5961]

I have Chevrolet cruze 2011 LT but it doesn't have TPMS SENSOR...

[@vladimirvladimir5734]

Thank you very much, you helped a lot. Buick Encore 2018.Hi from Belarus

[@4ever2high0]

Dude just say this and went to go try it and it worked.. I've had this 2011 cruze for about 6 months and always had that light on. And not registering my front right.. it was so annoying to see it every time I started my vehicle.. and now no moo. Thank you so much. 🤘

[@FalconsGarage]

AWESOME!!! Glad I was able to help!!

[@bradwjensen]

My sensor wasn't reading after some battery/cable work. I was going to re-set it like this video shows, so I filled the tires from 35ish to 49 psi and when I got back in the car the sensor was working again! :) Took about 10-15 PSI until it started working again because one of the tires I put a little less pressure in and that still wasn't working until I added a slight bit more pressure. No beeps or anything. Then I released air back down to 35 PSI and the sensor knew. :)

[@winboogie42]

Thx simple & sweet but enough detailed to understand what needs to be down & how.

[@Booker2663]

went to Belle Tire, they wanted to chage me $60 to relearn my TPM. VIdeo much appreciated!!...

[@lelyyarreoroc3384]

Thank you so much my car is doing the same the tires r good but the light won’t turn off I’m try this when I wake up ✨

[@330drs]

2012 GMC Acadia Denali, turn ignition on with engine off then press the LOCK and UNLOCK button on the key FOB for approximately five seconds until the horn sounds then follow the directions on the video.

[@68chevelle57]

Thank you so much for this information I definitely can use it without the machine

[@frankmurawski4952]

Worked great! Thanks so much!

[@carltonsmith3428]

Great video man very informative

[@bnkfoster]

great video boss. worked like a charm first time. thank you for sharing!

[@FalconsGarage]

Great to hear!

[@dominicsummonte1838]

I like his garage nice setup

[@albertvillar4732]

Great video - Thanks!!!

[@sageorozco4288]

Easy to follow & supper helpful!!!!

[@FalconsGarage]

Glad you think so!

[@chiefspacely]

lmaooo ‘did u notice it scared me’😹😹😹 thanks for the tips!

[@FalconsGarage]

LOL No problem!!

[@amarilisrecinos1547]

Thank you I’m going to pick up my car to reprogram myself to GMC Terrain 2010 I’ll come back to share my results

[@Crispy1960]

Thanks man! saved me some $$, and told this to my local tire store-they didn't know you could do this without the TPMS tool.

[@lawlor2925]

Ur a fkn genius! I knew there had to be a way to do this w.o the tool. They just want u to service it at a shop or buy it. Otherwise they'd put this in the owner's manual. Gracius mi amigo Edit. And oh I have a 2011 buick and it worked perfect

[@FalconsGarage]

Glad I could help you safe some money!

[@lawlor2925]

@@FalconsGarage yes thanks a lot. I dont ever go to a shop unless I deff can't figure it out. Thanks to heros like u lol

[@ernyloewen9997]

It helped me out thx

[@mcrispi2963]

Cool video, right to the point, thank you

[@mrbenjaminvincent]

Didn't work only thing happened was air out tire 2014 chevy cruze ls

[@robburke8867]

Thanks. Great info

[@vortex7748]

Nice

[@timothybosley7987]

Just finished an oil change and tire rotation and was surprised by the fact that it didn't automatically know where the tires had been moved to. Never had to do a manual relearn with my Ford. Didn't even know what a relearn tool was. Found your video and thought great, I can finish this up now so everything's good for my wife next time she drives her car. But it didn't work for me on a '15 Cadillac SRX.

[@FalconsGarage]

most fords wont tell you exactly what tire is low thats why they dont need reprograming ... and yeah Cadillac are more difficult.

[@marciabaxley1959]

Thanks so much

[@ericlavoie399]

thanks it work on my gmc terrian

[@FalconsGarage]

Awesome.. glad to help!

[@elloco7429]

Thank you.

[@eddiemason3998]

Thank you

[@antoniomendez3327]

Chingon bro

[@jorgiluis3433]

Awesome 👍

[@FalconsGarage]

Thanks 🤗

[@bigdog911paradio3]

Thank you brother

[@FalconsGarage]

No problem

[@buttsilike1209]

HA Dude you just saved me money...Thanks man........

[@FalconsGarage]

Glad I could help

[@titomolina7347]

thanks

[@SladesVWBeetle]

I'm going to be purchasing aftermarket rims. I am so happy you put this video up I have a 2013 Chevy Malibu but it appears to be the same situation. Do I have to get special valve stems for my new Wheels? I'm staying with original manufacture size. Just a fancier rim. Same size. I didn't know if the valve stems are special type?

[@FalconsGarage]

yes you need to get valve stems with the chip on it to read the pressure .. im not sure if the original ones will fit aftermarket rims

[@SladesVWBeetle]

Oh crap! Well maybe I'll just spray my rims...LOL Do you also do this if if you do a tire/wheel rotation?

[@FalconsGarage]

yes.. because the sensor wont be on the same location as before .. and it will read the wrong tire

[@thecentralman]

Thank you for a great vid, now I don't have to pay extra for TPMS reset when I rotate my tires.

[@FalconsGarage]

Glad I could help!

[@MrsSunshine75]

Thank you, thank you, thank you!

[@FalconsGarage]

lol Glad I could help!

[@blue04mx53]

Hi, Do you know if this procedure still works on a 2018 Sonic ?

[@Icutmetal]

Golden info; I just rotated the tires on my 2500HD and wondered if there was a way around buying the TPMS tool. Thank you!

[@FalconsGarage]

Glad I could help

[@ImaLoneWolfintheWoods]

Did this work on your truck? What year is truck? Won't work in my 2015 1500

[@Icutmetal]

@@ImaLoneWolfintheWoods No it didn’t; tried it a few times, and every time I thought I had it, nope. Bought a Chinese TPMS reset device off eBay and it worked like a charm in less than 5min. I’ve got a 2018 2500HD.

[@ericlavoie399]

2010 GMC Terrain same

[@Lightningstorm2010]

I know this is a year later but how do I calibrate the compass. I have a 2016 Chevy Cruze 1LT

[@judas9966]

Is this what I need to do if one sensor is reading 1psi after I blew a tire and replaced it? I put a new one on and it still says 1 so I figured it just needed reset

[@JohnDoe-rs2pn]

I need this for the 2014 Buick LeSabre

[@velindoban7174]

I wanna ask. how if the GM cars using start stop engine buttone, which is do not using a key. how can you reset it?

[@jamesszalla4274]

I have a 2013 GMC Acadia. I simply inflated the tires to the proper level then drove about 30 miles on the highway at 65 MPH. System reset itself. Used to reset the system with the tool until I learned about this hack.

[@FalconsGarage]

yes, that also works .. Glad I could help!

[@kaye1118]

thanks! I hope this will work for me! the warning and light suddenly and randomely came on one day "service tire monitor system". I don't want to go to dealership or buy that tool. maybe I just need to put air in it or decrease the air? guess ill find out when it beeps lol

[@FalconsGarage]

could be a bad sensor.. but sometimes resetting helps

[@mikewhite3123]

Wide recently bought a Chevy from a used dealership and one tire said 28 pounds,but had over 90 in it lol don't know what stealership idiot did that,but this worked.

[@Travos69]

Well it didnt work for my 2016. The relearn started and front dr sd parking lamp came on. Went from 33 to 8 psi and no beep tried from 8 to 60psi and no beep. 😢

[@financeranger]

Tried on a 2014, no beep after letting 15lbs out or adding 15 back. Looks like I will buy a reset tool. Good news tho my home compressor had a better air gauge so relying on a service station reading was the problem and the air compressor that came with my ECO isn’t accurate either.

[@FalconsGarage]

If it didn’t work .... you might have a bad sensor. That would be my guess. The tool might be a little expensive compared to taking it to a firestone or dealer to get it done. They might charge you about $50 I’m assuming and the tools are usually over $100.

[@financeranger]

Falcon's Garage I might try the generic ones they are $20.

[@JoshuaCussins]

I dont think you can do the air process on 2014 plus. Does not work on 2014 GMC savana.

[@michaelAMaccarr]

Didn’t work on 2014 buick encore

[@jackmcminn2520]

Thanks for the video..how long do the sensors last should you replace them when buying new tires

[@FalconsGarage]

they almost never go bad .. so I would say don't replace unless they go bad

[@williamraysv]

Falcón do you have a video regarding power engine reduced? I've chevy cruze 2012 thanks in advance

[@FalconsGarage]

I dont but you need to get it scanned to see what other codes come with it

[@TacticalBuffoonary]

Will this work on a 2018 gmc savanna van?

[@JamesBondzX]

Does it work with new tpms, or has to be programmed?

[@girlperson1]

If you have one TPS sensor that's broke, will the system still allow you to complete the calibration process for the remaining 3 tires?

[@FalconsGarage]

no.. lets say you follow the procedures on the videos and will call the first tire we did tire #1 ans the last one we did will be tire #4 .. if the sensor is bad for tire #2 or #3 the system won let you go on to the rest of the tires until it reads the one is suppose to. Hope that made sense to you

[@bricksselfmade4.207]

Falcon's Garage ok I get it. So On my Chevy Cruze the reading for the tire sensor #1 doesn’t show but all other 3 sensor showing the tire pressure shows up.#1 sensor is broken and needs to be replaced

[@elmerpayes8859]

Hi do you know if I can do a manual relearn cramshaft sensor relearn? On a 2007 Chevy Silverado 1500?

[@FalconsGarage]

as far s i know you need a scanner for the relearn

[@kotaris01]

Does it work in all kind of cars?

[@brianhamric4170]

2013 Buick Verano and dash says learning but I deflate and nothing happens. Car says low tire pressure but light stays on and no beep. What am I missing ?

[@FalconsGarage]

IF the car is in learning mode but when you deflate nothing happens .. most likely your sensor is bad and needs to be replaced

[@brianhamric4170]

I did some research and turns out if you have a push button start you cannot trigger it with deflating. Only works with standard key start ignition.

[@supboy8939]

@@brianhamric4170 even for my Buick verano

[@mohamedothman1924]

Same thing happened in my 2014 Buick Verano it might be the sensor damaged. I didn’t change it yet I would to jump that stupid things for ever.

[@1Goldcutty]

Can you sync a camaro tps sensor to a pontiac g8 gt using same method???

[@FalconsGarage]

if they are the same part numbers.. yes

[@Laredo956]

I just changed my seat belts for my 2016 Cruz, and I'd like for the air bag light on the dashboard to turn off, what can I do to turn it off.? Or do I need to take it to a dealership.? Thanks in advance!

[@FalconsGarage]

you can try disconnecting the battery for about 5 minutes... but air bag lights wont always clear when the battery is disconnected... ...if not find somebody that has an ODB that reads air bad codes... and have them clear it for you ... maybe a autozone or oreillys ... hopefully they are using a bigger ODb and not the tiny one

[@MasterMotoTv]

Anytime you unplug air bags. Always make sure you disconnect your battery first

[@DennisEmahiserJr]

Can you recommend a good brand sensor that will work for a 2011 Aveo? Two different sensors didn't work. I don't have a key fob. I ended up taking it to the dealer and they get it cleared out, but when I went to leave, the light came back on. I'm thinking it's maybe a plug issue.

[@FalconsGarage]

I would use dealer sensors

[@DennisEmahiserJr]

@@FalconsGarage Thinking it may be a plug issue because two places showed that the sensor was working. Who knows!

[@albertortiz5177]

What about a 2015 Cadillac ATS?

[@kimberlyleforte6262]

Will this work on a 2020 chevy tracy Ltd? I just bought it (used) needed 2 put air n tires & manual sucked at helping a woman reset the light!! Thank you so so so much!!!!!!!

[@FalconsGarage]

the relearn yes ... but not sure if you can access the system the same way.

[@hogwildboi]

What if you start the relearn process on a 2009 Silverado and release air from the front left tire nothing happens so i go to the next tire and everything works correctly from there except i ended up on the tire i should've started with, what is that?

[@FalconsGarage]

then you have most likely a bad pressure sensor on that side

[@ParadiseIslandDun]

I have replaced all my tire sensors twice in Buick Regal 2011 ,due to a service TPMS alert. The indication light went off after reprogramming but comes back within a day. Tires inflated don’t know what else.

[@FalconsGarage]

could be the system it self having issues

[@staskornev]

For trax 2017 cant finish action with first left wheel and others. Ive droped out air but nothing ..no horn sound. Ive started drop air pressure about from 2,5. Whats wrong? please help.

[@FalconsGarage]

if you cannot get passed the first wheel is it most likely that that sensor is bad

[@ricardoramos588]

Hi there , how about to relearn tpms when you change wheel size and the light comes, on 2018 silverado, thanks in advance..

[@FalconsGarage]

not sure if the dash on that truck has a relearn button BUT first make sure that the new rims have TPS ... because most dont

[@ricardoramos588]

@@FalconsGarage ok, I'll check, thanks..

[@Hunter-nb5fc]

Falcon's Garage my new tires do have the sensors, how can I relearn my system? I have a 2017 Silverado.

[@lindseydavis9418]

I changed one sensor on my 2012 Chevy Cruze and haven't had success with the relearn process shown. The service tire monitor system light is on now. Any suggestions?

[@FalconsGarage]

Assuming the sensor you out on is good. You might have to take it to the dealer or a tire shop to have them program it with the scanner. But really don’t see why this procedure wouldn’t help you if everything g is working properly.

[@lindseydavis9418]

@@FalconsGarage thank you!

[@lindseydavis9418]

I bought a scanner and that did the trick! Thanks again for the video and your response!

[@kevinrice5268]

What if don't blow on second sensor

[@AlfredoCrazyFreddyRivera]

What about a 2017 Malibu Premier same way, or different broski... ?

[@FalconsGarage]

as long as you can open the system from the dash is the same

[@sestren2503]

Does this work on a 2015 camaro? Everyone I talk to says you have to have the tool to do it, It's not push button start. Both left sensors display a pressure. Both right sensors just have - - where the pressure should be. What's up with mine?

[@FalconsGarage]

the procedure of how to programing them by adding or releasing pressure works on any car .. as far as to HOW TO OPEN UP THE LEARNING PROCESS . might be different on the camaro and even with a tool .. you still need to know how to access the learning program on your car

[@AirmanJH]

I was hopeful, but didn’t work on my 2014 Sierra. It said learning was active, but releasing the air didn’t work.

[@FalconsGarage]

they probably a bad sensor

[@AirmanJH]

@@FalconsGarage Don’t think the sensor bad. They all work fine other than showing the wrong location. By the way, this process worked perfectly on my Buick. So thank you!

[@shawnphillips1220]

I followed your steps. Held lock and unlock and car honks twice and says tire set up. My front headlight comes on but after letting out air, it doesn't honk. I tried it for about 10-15 seconds so probably not 10 psi. Should I try again or you think I'll need a reset tool? 2012 Buick Enclave.

[@FalconsGarage]

dont think its enough time .. but make sure you have a compressor handy

[@michaelAMaccarr]

Didn’t work on 2014 buick encore

[@Koldkillakid99]

How much does it usually cost to change one tire pressure monitor system? I also have a 2012 Chevy Cruze

[@FalconsGarage]

not sure .. dont work on tires

[@marionkarhatsu5255]

Didn't work on my 2013 Cruze.... do you need to start at a higher than normal pressure? I started at 38 psi and it never beeped on releasing the air... and I went down to 15 psi.... or does it mean that they TPMS isn't compatible with my vehicle after all (manufacturer says it is compatible)?

[@FalconsGarage]

if it didnt work .. maybe the sensor is bad

[@stevelozano9523]

I wished this would have worked but didnt on my 13 cadillac ats. They were all working until I changed the bcm then stopped working.

[@FalconsGarage]

Cadillac is usually a different ball game ... you most likely need a special scanner for it

[@LexieLou435]

I just bought my 2015 chevy Cruze. This light was on, it’s only showing 1 tires pressure- before it showed 2. The tires have air and aren’t low. Will this work for me?

[@FalconsGarage]

yes it should . but could also be that your sensors are bad!

[@ReverseEngineered]

works on 2012 chevy cruze as of Jan 2019

[@jagdiprandhawa1516]

Reverse Engineered i got 2015 chevy and it didn’t honk, I drained all the air 😐

[@bricksselfmade4.207]

Didn’t work on a 2013 Chevy Cruze i let out the air on 4 tires

[@bricksselfmade4.207]

Jagdip Randhawa did you get it fix and how?

[@jagdiprandhawa1516]

BricksSelfMade 4.20 nope.. i think i have faulty sensor, i just pay attention to it anymore

[@bricksselfmade4.207]

Jagdip Randhawa damn okay did you get a estimate by chance ?

[@jorgeescobar9902]

Para un Buick verano 2012

[@compassion3595]

Will this work if one of the sensors isn’t working? I have a 2015 Chevy Cruze

[@FalconsGarage]

no, if one sensor isnt working the procedure... will stop on that wheel and cannot continue

[@compassion3595]

Falcon's Garage thank you for your response. Just what I thought :( I have a Tpms reset tool which stops on one wheel and won’t continue. Which i find weird, because just before I went into relearn tire mode, that sensor was working fine and reading pressure. Ah well. Guess it’s back to the trusty tire pressure gauge in the trunk. That never fails.

[@ibrahimm218]

I have a 2011 honda odyssey and got my tires rotated now the low tire pressure sign went away but a new tpms sign came on

[@FalconsGarage]

you need to get them re-programmed

[@ibrahimm218]

@@FalconsGarage thanx for the reply they reprogrammed by themselves after driving for more than 30 minutes

[@twotoneprixflako956]

i have a 2014 camaro i have air on all my tires but the light its still on ! what could it be? bad sensors

[@FalconsGarage]

aither you have a bad sensor or they are not programmed .. also does it have the correct amount of air?

[@817mario]

Will the reset work even tho one of my sensors don’t show a psi number ? You think maybe that sensor is faulty ?

[@FalconsGarage]

if the sensor is good yes it will work .. but if its bad it wont work and it wont get passed the bad sensor, but if the sensor is good then it will work

[@817mario]

Falcon's Garage yea cause I tried it the other day and they all Honked except 1 and now none show ps1 at all. But before I reset it 3 we’re working except 1.

[@FalconsGarage]

Mario 817 I would say it’s bad then.

[@817mario]

Falcon's Garage I’ll try it again then I’ll just replace it. Thanks man

[@10milliBuddha.]

Would this work if I’m using a whole new rim and tire with a censor already on it? My old rim got bent

[@FalconsGarage]

as long as is a factory sensor.

[@JonathanLopez-ji1zx]

Mine shows PSI on all wheels except on one it’s blank ..? Does it need to be replaced or just relearn ?

[@blainedupre3392]

My 2019 Equinox is showing the same issue. Literally 1 month after I bought the vehicle, we brought it in for the first service, and this happened after the tire rotation (I'm assuming). I'm also assuming that the part isn't bad since it's still new... I'm going to play around with it and post an update.

[@thesteveman509]

Did not explain how reset. I filled the tires, however still getting warning tires pressures low

[@FalconsGarage]

lol .. what? i just explain everything on the video .. is you still getting the light most likely you have a bad sensor

[@ryandaniels2686]

So you keep releasing the air until you hear a beep? Sometimes it may take longer?

[@FalconsGarage]

yes.. and it dosent beep .. then there is something wrong with either the system or the sensor

[@smartass8084]

Does it matter what tire you start with ?? Can’t get any to beep 🤔

[@FalconsGarage]

Smart Ass yes it matters. Follow the pattern from the video

[@smartass8084]

Falcon's Garage I got it thanks !! I had drivers door open thinkn that was why shut it and it worked 🤔

[@lmezy25]

So it beeps when its thinks it has the right psi??? I have a 14 ltz and one tire shows low on the digital end but 32 with the tire pressure gauge

[@FalconsGarage]

no .. it beeps when it has sensed the sensor .. not at the right psi

[@lmezy25]

@@FalconsGarage if my max PSI on my tire indicates 50 what should I keep it at

[@FalconsGarage]

most cars are 35 .. but check your manual

[@kirbyroad5743]

I've got a 2012 silverado and I've tried this after replacing the wheels and tires. But no matter how much air I release the truck is not picking up the sensors. I can bleed it flat and no beep. My dash says it is in relearn mode and it beeps twice but it won't pick up the new sensors. I know they are good because the wheels came off another identical truck and were working fine. So what's up?

[@chrismann1621]

I think since it's a totally different sensor from either a new vehicle or new out of the box the initial learn procedure has to be done to the truck. They work on slightly different frequencies. I think your truck doesn't know its looking for your "new" sensors.

[@kirbyroad5743]

@@chrismann1621 yep bought a sensor programmer off of EBay for $15.00 and just point and push a button. Truck picks up the sensor and in 2 min. done.

[@Darjan_Spasojevic]

My 2022 trax, same set up didn't work.

[@NoahTheFacts]

Does anyone know if this works to learn 4 all new GM sensors on winter tires with separate rims? These are OEM sensors, not universal programmable sensors.

[@FalconsGarage]

should as long as they are factory sensors like you mentioned

[@NoahTheFacts]

Thanks!

[@NoahTheFacts]

Not sure what I’m doing wrong, but I can’t get the chirp out of the tire by letting air out. 2019 Buick Encore.

[@noirnyx1061]

My car wants 35 PSI. if I give it 40 and deflate it to 30-35 even though that's not 10-15 over will it still reset?

[@FalconsGarage]

It might it might not. But even if you go under 30 you can always add air back on to it.