Rewiring An Entire Car | Z2H8 Drag Car Camaro

[@ericnelson6982]

First time to the channel, everything you showed today was very impressive. I am an old man that cannot do much anymore because of my health has not been good. I built some Nova's and an 67 Camaro for myself. I spent a lot of time and effort building other people's cars to keep the bills paid. It is very nice seeing this build, I will check out some of your other video's. Keep at it, it will pay off when your finished.

[@YerkitRacingChannel]

Wiring and panels look amazing very clean install. Like the idea on the kabota switches!

[@DAPerform]

Thanks a lot!

[@chrissybert6543]

Very nice job! I'm getting ready to wire my 63 chevy II drag/street car your videos gave me so much confidence and all the products are great!

[@DAPerform]

That’s awesome to hear. It was a bit overwhelming but take your time and do your research and it’ll go seamless

[@vandettabuilds6641]

Terrific!!! You have done a fantastic job!!

[@Optimusprimerib]

Nice work, Hannibal!

[@DAPerform]

Thanks ?

[@mattsantoro1480]

Looks killer guys. Some OCD right there. Keep up the great work.

[@DAPerform]

Going for that clean look! Nothing worse than spaghetti wiring 😂

[@tbrad110]

Bro the headlight switch is genius.

[@DAPerform]

Cheap and easy hardest part was figuring out what wire goes to what

[@flackoscustoms5920]

Any chance you can go over the wiring? On the switch?

[@badmudderrutters7460]

FUCK YEA!!! Almost there Doug. Kind of pissed off KZbin never notified me of any new recent videos you made.

[@DAPerform]

Oh damn, make sure your notifications are on 🤘🏼

[@steventerry9462]

Awesome job

[@DAPerform]

Definitely means a lot, thank you for all the help! 🤘🏼

[@6.8SuperDutyDriver]

Good show!

[@powers6963]

Great video and clean install. Just about to install one of those Leash boards myself. Question - where did you find those small turn signal and high beam indicator lights in the dash? That's genius! Do you have a link by chance?

[@DAPerform]

Found them on Amazon. Inexpensive and they are also very small

[@backpackerdad6905]

Great build!! Hey what are using for your digital dash screen, and how are you feeding info to it? thanks.

[@DAPerform]

Holley 7” screen its feed is through a can bus wire in the engine harness

[@burtgummerVerified]

Update on the Ranger?

[@DAPerform]

Still kicking as my daily driver nothing but some routine maintenance

[@carsonpurcell2611]

If you dont mind me asking, what was the pin out for the headlight switch? Seams the easiest way to go for me but cant find a pin out diagram anywhere

[@DAPerform]

I’ve got it written down somewhere, It took me about 15 minutes to ring out each wire and what powers what. Find my Facebook page or Instagram and message me and Ill send you a picture of the wiring diagram I came up with

[@flackoscustoms5920]

Can I get it as well? I can email you

[@joshuajohnson3500]

Hey question, i have the same relay board and harness im new to this wiring stuff but im learning lol but anyway for the Relay output side of board #1(IGN) Relay with the red 10gauge wire what you hook that (IGN) wire too or what device? im using #2 relay for starter if you dont mind me asking. Im building a S/S c6 corvette with holley terminator x max

[@DAPerform]

The red and white wire coming off of the Holley harness goes to the ignition relay on the relay board I stepped does the wire from 10ga to 14 to a Deutsch connector and about 6 inches of the wire off of the harness

[@joshuajohnson3500]

@@DAPerform the 12v switched RED/White wire coming off the Holley Harness Gotcha thanks man

[@DAPerform]

@@joshuajohnson3500 that’s the one. The other red wire you need to connect to the battery or to a good clean power source. The switched power turned on the relay for the ecu injectors and coil packs

[@joshuajohnson3500]

@@DAPerform Gotcha thanks for that information and keep up the good work on your build bro

[@DAPerform]

@@joshuajohnson3500 I appreciate it thank you!

[@JMcPheeters72]

Quick question how did you wire in the hazard to that panel

[@DAPerform]

Just ran power to an auxiliary switch back to the hazard input on the relay board. The flashers are built in

[@pbclax1]

Where were you able to find that kubota switch?

[@DAPerform]

It’s not an actual Kubota brand, its a knock off but works the same and I’ve had no issues with it so far

[@pbclax1]

Awesome…Amazon?

[@DAPerform]

@@pbclax1 Amazon or eBay I can’t recall

[@burtgummerVerified]

This channel was so much more interesting when it was about the Holden Commodore...

[@DAPerform]

There’s future episodes and plans about the g8 coming soon

[@burtgummerVerified]

@@DAPerform I'm a sub. VE will be cool!!

[@lauraleedoro1844]

This is pretty cool. Increase your engagement easily --> p͎r͎o͎m͎o͎s͎m͎!!